EF Logo

SPN and FMI fault codes (J1939)

Every modern diesel reports faults the same way: an SPN that names the part or reading, and an FMI that says how it failed. Find the SPN for what is at fault, then the pair for the exact failure.

216 codes, plus 107 SPN + FMI pairs28 stop now, 176 check soon, 12 info

216 SPN codes - type a code, or a word from the problem.

Covers Trucks, Excavators, Loaders, Generators.

Where to look

  1. 01Connect a J1939-capable scan tool to the 9-pin diagnostic port.
  2. 02Read active faults first, then stored faults, and note the SPN and FMI of each.
  3. 03Check freeze-frame data for the conditions when the fault set.
  4. 04Fix the root cause.
  5. 05Clear fault memory and road-test to confirm it does not return.
How to read J1939 fault codes, in full
  1. Connect a J1939-capable scan tool to the 9-pin diagnostic port.
  2. Read active faults first, then stored faults, and note the SPN and FMI of each.
  3. Check freeze-frame data for the conditions when the fault set.
  4. Fix the root cause; result codes like SPN 1569 and SPN 5246 go away once the cause is fixed.
  5. Clear fault memory and road-test to confirm it does not return.

How urgent is a J1939 code?

Stop now28 codes
Shut down and fix before working on. Running on risks damage or the machine locks out.
Check soon176 codes
The machine may derate or limit a function. Find the cause before the next shift.
Information12 codes
A reminder or status message. Nothing is failing yet.

Pick your system

Find the part of the machine, then the family your code belongs to.

Code range
The first and last code in the family, as the machine shows them.
Codes
How many codes the family holds; each is explained on its page.
Severity mix
The share of stop, check and info codes. The dot after it is the most urgent one in the family.

EGR11 codes

Air intake17 codes

5 more in Air intake

Aftertreatment - DPF46 codes

34 more in Aftertreatment - DPF

Sensors7 codes

Fuel system30 codes

18 more in Fuel system

Lubrication6 codes

Turbo16 codes

4 more in Turbo

Cooling12 codes

Electrical10 codes

Engine speed/timing13 codes

1 more in Engine speed/timing

Aftertreatment - SCR/DEF48 codes

36 more in Aftertreatment - SCR/DEF

Most searched J1939 codes

SPN + FMI pairs

The combinations looked up most, each with the causes of that exact failure.

FMI codes 0 to 31

The failure mode after every SPN, the same for every engine maker.

FMI 0Data above normal, most severeValue is far above its allowed range; the worst-case high alarm.
FMI 1Data below normal, most severeValue is far below its allowed range; the worst-case low alarm.
FMI 2Erratic or incorrect dataSignal jumps around or disagrees with other readings, often a loose connection or failing sensor.
FMI 3Voltage above normal or shorted highCircuit voltage is higher than it should be, typically a short to supply or an open on a pull-up signal.
FMI 4Voltage below normal or shorted lowCircuit voltage is lower than it should be, typically a short to ground or a lost supply.
FMI 5Current below normal or open circuitAn output or load draws less current than expected, so the wire or the load is open.
FMI 6Current above normal or grounded circuitAn output draws too much current, so the wire or the load is shorted.
FMI 7Mechanical system not respondingA commanded actuator or valve is not moving or not giving the expected result.
FMI 8Abnormal frequency, pulse width or periodA speed or PWM-type signal has the wrong frequency or timing.
FMI 9Abnormal update rateData or a message from another module arrives late, slowly or not at all.
FMI 10Abnormal rate of changeThe reading changes faster or slower than a real physical value could.
FMI 11Root cause not knownThe ECM sees a fault but cannot say which of several causes is responsible.
FMI 12Bad intelligent device or componentA smart module or sensor reports an internal failure.
FMI 13Out of calibrationThe device needs calibration or its calibration data is wrong.
FMI 14Special instructionsA maker-defined condition; read the engine maker's fault tree for what to do.
FMI 15Above normal, least severeValue is above range at the earliest, mildest warning level.
FMI 16Above normal, moderately severeValue is above range at the middle warning level, often with a derate.
FMI 17Below normal, least severeValue is below range at the earliest, mildest warning level.
FMI 18Below normal, moderately severeValue is below range at the middle warning level, often with a derate.
FMI 19Network data errorA value received over the data link is flagged as bad by the sending module.
FMI 20Data drifted highReading is still in range but has crept upward from its expected value.
FMI 21Data drifted lowReading is still in range but has crept downward from its expected value.
FMI 22ReservedNot given a meaning in the lists consulted; do not rely on it.
FMI 23ReservedNot given a meaning in the lists consulted; do not rely on it.
FMI 24ReservedNot given a meaning in the lists consulted; do not rely on it.
FMI 25ReservedNot given a meaning in the lists consulted; do not rely on it.
FMI 26ReservedNot given a meaning in the lists consulted; do not rely on it.
FMI 27ReservedNot given a meaning in the lists consulted; do not rely on it.
FMI 28ReservedNot given a meaning in the lists consulted; do not rely on it.
FMI 29ReservedNot given a meaning in the lists consulted; do not rely on it.
FMI 30ReservedNot given a meaning in the lists consulted; do not rely on it.
FMI 31Condition existsThe fault condition is present but the maker gives no finer detail; look at the SPN itself.

Quick answers

How do I read J1939 fault codes?

Connect a J1939-capable scan tool to the 9-pin diagnostic port. Read active faults first, then stored faults, and note the SPN and FMI of each.

What do SPN and FMI mean?

The SPN (suspect parameter number) names the part or value at fault; the FMI (failure mode identifier) says how it failed. FMI 3 is "voltage above normal or shorted high", FMI 4 "voltage below normal or shorted low". The same 32 FMI numbers apply to every engine maker, so read the SPN for where to look and the FMI for the first test.

Which J1939 codes mean stop now?

28 of the 216 J1939 codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example SPN 100, SPN 110, SPN 111, SPN 157. 176 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.

What should I check first on a J1939 code?

Most J1939 codes here (131 of 216) read as lost message: a module stopped hearing another on the data link, or the data came late or garbled. First test, as general workshop practice: key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

Which J1939 codes are looked up most?

SPN 27 (egr valve position), SPN 81 (dpf intake pressure), SPN 91 (accelerator pedal position), SPN 94 (fuel delivery (low-side) pressure), SPN 95 (fuel filter differential pressure). Each page gives the meaning, the likely causes and the checks.

Sources

Every code was read from these documents and written in our own words.

4 more sources

Other makers

Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.