J1939 · Turbo
SPN 1209 Fault Code
Engine exhaust gas pressure
What does SPN 1209 mean?
Pressure in the exhaust, read by a sensor ahead of the turbine or in the exhaust manifold. The ECM uses it for EGR, exhaust brake and turbo protection. How urgent it is depends on the FMI after SPN 1209 - pick it below. Check first: compare the exhaust pressure with the DPF differential pressure and boost under load.
- SPN 1209
- Engine exhaust gas pressure
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 1209 - pick it below.
What should I check first?
Compare the exhaust pressure with the DPF differential pressure and boost under load
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 1209?
You'll notice: Exhaust pressure ahead of the turbo is out of range, so the ECM sees a restriction or a sensor fault.
Find the number shown after SPN 1209 on your display.
- 2SPN 1209 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, PACCAR MX-13
- 3SPN 1209 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, PACCAR MX-13
- 4SPN 1209 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, PACCAR MX-13
- 10SPN 1209 FMI 10: Exhaust pressure before the turbine is out of calibration or responds too slowlyErratic or implausiblePACCAR MX-13
- 11SPN 1209 FMI 11: Exhaust pressure before the turbine is too highReal conditionPACCAR MX-13
- 16SPN 1209 FMI 16: Value is above the normal range, moderately severe levelReal conditionCummins ISX15
- 17SPN 1209 FMI 17: Exhaust pressure before the turbine is too lowReal conditionPACCAR MX-13
- 18SPN 1209 FMI 18: Value is below the normal range, moderately severe levelReal conditionCummins ISX15
Checks
0 of 5 done
When to stop
Make the machine safe before you start: on firm level ground, attachments down, key out.
How urgent SPN 1209 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Exhaust restriction after the turbo, such as a blocked DPF, damaged silencer or collapsed pipe
- VGT vanes stuck closed or a brake flap held shut, raising exhaust pressure
- Exhaust pressure sensor or its sensing line blocked with soot
- Sensor wiring fault: open, short or heat-damaged connector
Other Turbo codes
- SPN 641Variable geometry turbo (VGT) actuator
- SPN 3251DPF differential pressure
- SPN 642Variable geometry turbocharger actuator 2
- SPN 1127Turbocharger boost (intake manifold) pressure
- SPN 1172Turbo compressor inlet temperature sensor
- SPN 1176Turbocharger compressor inlet pressure
- SPN 1188Turbocharger wastegate actuator
- SPN 2629Turbocharger compressor outlet temperature
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 1209 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
