Genie fault codes
Genie scissor lifts show a fault code on the control box display, S-series booms flash a source-and-type code, and GTH telehandlers report Deutz engine SPN/FMI codes. From Genie service and repair manuals.
303 codes in 15 families126 stop now, 142 check soon, 35 info
303 Genie codes - type a code, or a word from the problem.
Covers Scissor lifts, Boom lifts, Telehandlers.
Where to look
- 01Scissors.
- 02Booms.
- 03GTH.
- 04Repair the cause, then cycle the key switch or power.
How to read Genie fault codes, in full
- Scissors: read the code on the platform LED display or the ground control LCD.
- Booms (ALC-500): the alarm beeps twice every 30 seconds; open the platform box and count the red LED flashes (source) then the yellow LED flashes (type).
- GTH: hold the d button 5 seconds with the engine running to show active codes; SERVICE replaces GENIE on the LCD.
- Repair the cause, then cycle the key switch or power.
How urgent is a Genie code?
- Stop now126 codes
- Shut down and fix before working on. Running on risks damage or the machine locks out.
- Check soon142 codes
- The machine may derate or limit a function. Find the cause before the next shift.
- Information35 codes
- A reminder or status message. Nothing is failing yet.
Pick your system
Find the part of the machine, then the family your code belongs to.
- Code range
- The first and last code in the family, as the machine shows them.
- Codes
- How many codes the family holds; each is explained on its page.
- Severity mix
- The share of stop, check and info codes. The dot after it is the most urgent one in the family.
Hydraulic coil and motor controller faults (H)42 codes
Controls and ECM faults (C)24 codes
Power device faults (P)18 codes
Switch and joystick faults at startup (U)23 codes
Sensor and limit switch faults (F)26 codes
Battery charger codes34 codes
Control system fault codes (ALC-500 red/yellow LED)60 codes
Platform load sense faults (S-60 HC)55 codes
Operational indicator codes12 codes
Engine faults (Deutz TD 2.9, SPN/FMI)9 codes
Most searched Genie codes
- brBrake release
- CHChassis mode operation
- CHrgCharger interlock
- LLOff level
- LoHtLift height limited
- ndNo drive
- ObSObstruction
- OLPlatform overload
- PHSPothole guard stuck
- E-0-0-1Charger: high battery voltage
- E-0-0-2Charger: low battery voltage before charge
- E-0-0-4Charger: defective battery
- F005Pothole limit switch shorted
- F008Overload transducer shorted high
- F009Overload transducer shorted low
- F010Platform height sensor shorted high
- F011Platform height sensor shorted low
- C021PCON not detected
- 24-17Angle sensor not calibrated
- C025Platform overload not calibrated
- U033PCON drive joystick not centred at startup
- F034Height sensor not calibrated
- U037Foot switch pressed at startup
- C053PCON-GCON software mismatch
- C055Drive controller hardware failure (DCON type 01)
- C058Drive controller voltage out of range (DCON type 04)
- H070Motor controller throttle: short to battery negative
- H072Motor controller throttle: short to battery positive
- 76-12Platform load cell overloaded
- SPN 94 / FMI 1Low fuel pressure
- SPN 97 / FMI 12Water in fuel prefilter
- SPN 100 / FMI 1Low oil pressure
- SPN 110 / FMI 0High coolant temperature
- SPN 111 / FMI 1Coolant level too low
- F129Tilt sensor mismatch (UTS)
- SPN 157 / FMI 3Rail pressure sensor signal high
- SPN 190 / FMI 12Crankshaft speed sensor: no signal
- SPN 523633 / FMI 11NOx conversion rate insufficient
- SPN 524025 / FMI 14Particulate filter regeneration not successful
Quick answers
How do I read Genie fault codes?
Scissors: read the code on the platform LED display or the ground control LCD. Booms (ALC-500): the alarm beeps twice every 30 seconds; open the platform box and count the red LED flashes (source) then the yellow LED flashes (type).
Which Genie codes mean stop now?
126 of the 303 Genie codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example OL, F008, F009, C021. 142 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.
What should I check first on a Genie code?
Most Genie codes here (75 of 303) read as real condition: the sensor reading is valid but outside the allowed range - the problem may be real. First test, as general workshop practice: check the real value with a separate gauge or thermometer before blaming the sensor.
Sources
Every code was read from these documents and written in our own words.
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, pp. 166-171
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, pp. 170-171
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, pp. 180
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, pp. 166-173
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, pp. 174-176
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, pp. 177-179
30 more sources
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, pp. 184-186
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, p. 183
- Genie S-60/S-65 Service and Repair Manual 1268492, pp. 104-105
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 105
- Genie S-60/S-65 Service and Repair Manual 1268492, pp. 141-142
- Genie S-60/S-65 Service and Repair Manual 1268492, pp. 145-146
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, p. 164
- Genie GTH-5519 (Deutz Tier 4i) Service and Repair Manual 1272852, Section 4 Fault Codes
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, pp. 183-187
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, p. 177
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, p. 180
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, p. 178
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 140
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, pp. 178-179
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 141
- Genie S-60/S-65 Service and Repair Manual 1268492, Control System Fault Codes
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 142
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 143
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 144
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 106
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 145
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 146
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 107
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, p. 170
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, p. 179
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, p. 171
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 108
- Genie S-60/S-65 Service and Repair Manual 1268492, p. 109
- Genie GS-1530/1930/2032/2632 etc. Service and Repair Manual 1272217GT (Rev E1), Section 4 Diagnostics, p. 172
Other makers
Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.
Post a request