EF Logo

Deutz fault codes

Deutz engines with the EMR4 controller report a fault as an SPN and FMI, a Deutz KWP code and a blink code on the warning lamp. These are from the official Deutz EMR4 code list.

619 codes in 28 families38 stop now, 567 check soon, 14 info

619 Deutz codes - type a code, or a word from the problem.

Covers Telehandlers, Lifts, Loaders, Rollers.

Where to look

  1. 01Read the active and stored faults with Deutz SerDia on the engine diagnostic plug.
  2. 02Where no tool is at hand, many Deutz engines flash the blink code from the engine…
  3. 03Note the SPN and FMI.
  4. 04Fix the cause, clear the stored faults in SerDia, then run the engine and confirm the…
How to read Deutz fault codes, in full
  1. Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug; the list shows SPN, FMI and the Deutz text.
  2. Where no tool is at hand, many Deutz engines flash the blink code from the engine lamp when the diagnostic button is pressed; match the flashes to the blink code column.
  3. Note the SPN and FMI: the SPN names the component, the FMI says how it failed (3 is too high or shorted to supply, 4 is too low or shorted to ground, 5 is open circuit).
  4. Fix the cause, clear the stored faults in SerDia, then run the engine and confirm the code does not return.

How urgent is a Deutz code?

Stop now38 codes
Shut down and fix before working on. Running on risks damage or the machine locks out.
Check soon567 codes
The machine may derate or limit a function. Find the cause before the next shift.
Information14 codes
A reminder or status message. Nothing is failing yet.

Pick your system

Find the part of the machine, then the family your code belongs to.

Code range
The first and last code in the family, as the machine shows them.
Codes
How many codes the family holds; each is explained on its page.
Severity mix
The share of stop, check and info codes. The dot after it is the most urgent one in the family.

Intake air and boost47 codes

Coolant, oil and fuel sensors24 codes

EGR37 codes

High-pressure fuel system22 codes

Injectors and combustion57 codes

ECU hardware45 codes

Throttle and operator inputs22 codes

Exhaust aftertreatment (SCR)158 codes

Relays and outputs25 codes

Cooling and fan22 codes

Exhaust aftertreatment (DPF/DOC)89 codes

CAN communication and shutdown71 codes

Most searched Deutz codes

Quick answers

How do I read Deutz fault codes?

Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug; the list shows SPN, FMI and the Deutz text. Where no tool is at hand, many Deutz engines flash the blink code from the engine lamp when the diagnostic button is pressed; match the flashes to the blink code column.

Which Deutz codes mean stop now?

38 of the 619 Deutz codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example SPN 100 FMI 0, SPN 100 FMI 1, SPN 100 FMI 3, SPN 100 FMI 4. 567 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.

What should I check first on a Deutz code?

Most Deutz codes here (102 of 619) read as real condition: the sensor reading is valid but outside the allowed range - the problem may be real. First test, as general workshop practice: check the real value with a separate gauge or thermometer before blaming the sensor.

Which Deutz codes are looked up most?

SPN 91 FMI 3 (machine - position accelerator pedal (sensor 1) - voltage above normal or shorted to high source), SPN 91 FMI 4 (machine - position accelerator pedal (sensor 1) - voltage below normal or shorted to low source), SPN 91 FMI 11 (machine - position accelerator pedal (sensor 1) - root cause not known), SPN 94 FMI 1 (engine - fuel low pressure sensor - data below normal operational range (most severe level)), SPN 94 FMI 3 (engine - fuel low pressure sensor - voltage above normal or shorted to high source). Each page gives the meaning, the likely causes and the checks.

Sources

Every code was read from these documents and written in our own words.

42 more sources

Other makers

Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.