Deutz · Intake air and boost
Deutz Fault Code SPN 102 FMI 1
Engine - Charge air pressure sensor - Data below normal operational range (Most severe level)
What does Deutz code SPN 102 FMI 1 mean?
The charge air pressure sensor (in the intake manifold or charge air pipe) reports a value below the allowed range. This is a plausibility limit, so the low value may be genuine rather than a wiring fault. Urgency: check soon - the machine may derate or limit a function. Check first: inspect the sensor port, hose and seal for leaks.
- FMI 1
- Data below normal, most severe
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Inspect the sensor port, hose and seal for leaks
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- A boost leak, a dirty turbo or an air filter blockage can give genuinely low charge pressure under load
- Charge air pressure sensor drifting low or reading with an offset
- Oily intake manifold residue entering the sensor port
How it failed
You'll notice: Warning or derate: the boost reading is lost so the EMR4 limits fuelling; the machine feels down on power and may smoke, and a warning lamp can come on.
Real conditionRead from FMI 1: data below normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Intake air temperature and pressure sensors
9 other codes on this part are also real condition (SPN 105 FMI 0, SPN 105 FMI 1, SPN 107 FMI 0, SPN 108 FMI 0 and more). When they show together, start at the wiring and connector they share.
- SPN 102 FMI 1Engine - Charge air pressure sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 102 FMI 2Engine - Charge air pressure sensor - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 102 FMI 3Engine - Charge air pressure sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 102 FMI 4Engine - Charge air pressure sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 105 FMI 0Engine - Charge air temperature sensor - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 105 FMI 1Engine - Charge air temperature sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 105 FMI 3Engine - Charge air temperature sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 105 FMI 4Engine - Charge air temperature sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 105 FMI 11Engine - Charge air temperature sensor - Root cause not knownOtherCheck soon
Show the other 16 codesHide the other codes
- SPN 107 FMI 0Engine - Air filter differential pressure sensor - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 107 FMI 3Engine - Air filter differential pressure sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 108 FMI 0Engine - Ambient pressure sensor - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 108 FMI 1Engine - Ambient pressure sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 108 FMI 3Engine - Ambient pressure sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 108 FMI 4Engine - Ambient pressure sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 108 FMI 11Engine - Ambient pressure sensor - Root cause not knownOtherCheck soon
- SPN 171 FMI 0Engine - Ambient air temperature sensor - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 171 FMI 1Engine - Ambient air temperature sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 171 FMI 3Engine - Ambient air temperature sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 171 FMI 4Engine - Ambient air temperature sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 172 FMI 0Engine - Ambient air temperature sensor - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 172 FMI 1Engine - Ambient air temperature sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 172 FMI 2Engine - Ambient air temperature sensor - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 172 FMI 3Engine - Ambient air temperature sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 172 FMI 4Engine - Ambient air temperature sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 14
This source lists SPN 102 FMI 1 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
