EF Logo

Cat fault codes

Cat machines log a diagnostic code as a component number (CID) and a failure mode (FMI), and an event as E and a number. These are the 924H wheel loader and C6.6 engine codes from its maintenance manual; read them on the monitor or with Cat ET.

74 codes in 6 families11 stop now, 59 check soon, 4 info

74 Cat codes - type a code, or a word from the problem.

Covers Wheel loaders.

Where to look

  1. 01Turn the key on and check the cluster or monitor for a warning lamp, then open the…
  2. 02Connect Cat ET to the machine's service port and choose the right ECM.
  3. 03Open the active codes list first, then the logged codes, and note each CID, FMI or E code.
  4. 04Repair the active code that is lowest in the chain first, such as a 5 V or 8 V supply…
  5. 05After the repair clear the logged codes in ET and run the machine to confirm nothing…
How to read Cat fault codes, in full
  1. Turn the key on and check the cluster or monitor for a warning lamp, then open the service or diagnostics screen if fitted.
  2. Connect Cat ET to the machine's service port and choose the right ECM (engine, transmission or machine).
  3. Open the active codes list first, then the logged codes, and note each CID, FMI or E code.
  4. Repair the active code that is lowest in the chain first, such as a 5 V or 8 V supply code, before the sensors it feeds.
  5. After the repair clear the logged codes in ET and run the machine to confirm nothing returns.

How urgent is a Cat code?

Stop now11 codes
Shut down and fix before working on. Running on risks damage or the machine locks out.
Check soon59 codes
The machine may derate or limit a function. Find the cause before the next shift.
Information4 codes
A reminder or status message. Nothing is failing yet.

Pick your system

Find the part of the machine, then the family your code belongs to.

Code range
The first and last code in the family, as the machine shows them.
Codes
How many codes the family holds; each is explained on its page.
Severity mix
The share of stop, check and info codes. The dot after it is the most urgent one in the family.

Power supply10 codes

Engine sensors17 codes

Fuel system19 codes

Engine control11 codes

Transmission check9 codes

Event codes8 codes

Most searched Cat codes

Quick answers

How do I read Cat fault codes?

Turn the key on and check the cluster or monitor for a warning lamp, then open the service or diagnostics screen if fitted. Connect Cat ET to the machine's service port and choose the right ECM (engine, transmission or machine).

Which Cat codes mean stop now?

11 of the 74 Cat codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example CID 168 FMI 00, CID 190 FMI 08, E360, E361. 59 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.

What should I check first on a Cat code?

Most Cat codes here (17 of 74) read as shorted high: the signal sits at or near the supply voltage - more than a working sensor can send. First test, as general workshop practice: key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

Which Cat codes are looked up most?

CID 41 FMI 03 (8 v sensor supply voltage high), CID 91 FMI 03 (throttle position sensor voltage high), CID 91 FMI 04 (throttle position sensor voltage low), CID 100 FMI 03 (engine oil pressure sensor voltage high), CID 100 FMI 04 (engine oil pressure sensor voltage low). Each page gives the meaning, the likely causes and the checks.

Sources

Every code was read from these documents and written in our own words.

Other makers

Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.