EF Logo

Cat · Engine control

Cat Engine speed sensors, ECM data and data link fault codes

This page covers engine speed and timing sensors, ECM and personality module data faults, filter restriction events, the J1939 data link update rate and the throttle lock mode switch. The engine ECM reads crankshaft and camshaft speed sensors to time injection.

More about these parts

The engine ECM holds a personality module (software and settings). The ECM logs an event when a filter bypass or restriction switch shows that a filter is plugged.

FaultStopCID 190FMI 08Cat · Engine speed sensors, ECM data and data link
Code shows hereFAULTCID 190FMI 08

Where this code shows

Turn the key on and check the cluster or monitor for a warning lamp.

What do these codes mean?

Cat codes E172 to CID 549 FMI 02 are all about the engine speed sensors, ECM data and data link. The most common failure type is erratic or implausible (5 of 11); 1 needs an immediate stop. Start with this check: check the J1939 data link wiring and terminating resistors between the ECMs for opens and shorts.

How urgent are they?

1 of 11 codes here means stop now; the other 10 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon10

What should I check first?

Check the J1939 data link wiring and terminating resistors between the ECMs for opens and shorts.

Shared checks

11 of 11

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Cat E172High air filter restriction

    The engine ECM detected restricted airflow after the engine had run for 3 minutes.· Real condition
    Check soon

    Causes

    • Plugged air filter element
    • Restricted intake ducting
    • Faulty restriction sensor

    Checks

    1. 1Repair any active diagnostic codes in the list before working on the event itself.
    2. 2Inspect the air filter element for dirt and oil.
    3. 3Inspect the intake hoses for collapse and leaks.
    4. 4Replace the air filter element, clear the event and run the engine for 3 minutes again.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Cat CID 190 FMI 08Engine speed sensor signal abnormal

    The ECM lost the primary speed/timing signal, intermittently or fully, for two seconds.· Erratic or implausible
    Stop now

    Causes

    • Open in the engine control harness to the crank sensor
    • Faulty primary speed (crankshaft) sensor
    • Engine ECM

    Checks

    1. 1Connect Cat ET, try to start the engine and confirm 190-8 is active.
    2. 2Remove the right engine access panel and test the harness for an open in the speed sensor circuit.
    3. 3Inspect the sensor and its connector for oil, damage or a bad air gap.
    4. 4Check whether 342-8 is also active; both together point at the harness or ECM.
    5. 5Replace the primary sensor, then the harness, and last the ECM.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Cat E236Return hydraulic oil filter plugged

    The transmission ECM detects a plugged hydraulic oil filter.· Other
    Check soon

    Causes

    • Restricted return filter
    • Faulty bypass switch
    • Bypass signal circuit shorted to ground

    Checks

    1. 1Check the return filter and replace it if it is dirty.
    2. 2Test the filter bypass switch with a meter to see whether it is stuck closed.
    3. 3Run open and short tests at each harness connection.
    4. 4Tag harnesses before removing any so they go back in the same routing.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Cat CID 247 FMI 09J1939 data link abnormal update rate

    The engine ECM noticed another controller stopped, or wrongly started, sending the J1939 speed request message.· Lost message
    Check soon

    Causes

    • Open CAN data link 1 or 2 terminating resistor
    • High resistance or open in the engine harness
    • Lower cab harness open or shorted
    • Another module failing to transmit

    Checks

    1. 1Connect Cat ET, start or try to start the engine and confirm 247-9 is active.
    2. 2With power off, test the CAN data link terminating resistance.
    3. 3Inspect and secure the connectors on both CAN links.
    4. 4Run open and short tests at each harness connection between modules.
    5. 5Replace the faulty harness or resistor, then clear and recheck.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Cat CID 253 FMI 02Personality module incorrect

    The engine ECM found incorrect software.· Erratic or implausible
    Check soon

    Causes

    • Incorrect flash file loaded in the engine ECM
    • Replacement ECM not programmed for the machine
    • Interrupted software flash

    Checks

    1. 1Program the engine ECM with the correct software for the machine.
    2. 2Turn the ignition off for at least 30 seconds and back on.
    3. 3Recheck codes in Cat ET; if it has cleared the flash file was the cause.
    4. 4If it remains active, replace the engine ECM and program it.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Cat CID 261 FMI 11Engine timing not identifiable

    The ECM saw the primary and secondary speed sensors disagree by more than 8 crankshaft degrees.· Other
    Check soon

    Causes

    • Fuel injection pump timing wrong
    • Speed sensor signals out of step with each other
    • Primary or secondary speed sensor fault logged as 190-8 or 342-8

    Checks

    1. 1Check for 190-8 or 342-8 first and fix them before working on timing.
    2. 2If only 261-11 is active, test the fuel injection pump timing.
    3. 3If timing is correct, replace the injection pump.
    4. 4If timing is off, adjust it and verify machine operation.
    5. 5Clear logged codes and run the engine under load to confirm.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Cat CID 268 FMI 02Engine control module data incorrect

    The ECM found configuration parameters not programmed, such as flash files or injector trim codes.· Erratic or implausible
    Check soon

    Causes

    • Wrong parameters in the ECM flash file
    • Injector trim codes not entered after an ECM or injector change
    • Interrupted software flash

    Checks

    1. 1Program the ECM with the correct engine software.
    2. 2Clear logged fault codes after programming is complete.
    3. 3Verify machine operation with the engine under load.
    4. 4If the code returns, check that injector trim codes match the injectors fitted.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Cat E329Transmission filter plugged

    The transmission ECM detects a plugged transmission filter and logs the event.· Real condition
    Check soon

    Causes

    • Restricted transmission oil filter
    • Faulty bypass switch
    • Harness shorted to ground

    Checks

    1. 1Repair any active diagnostic codes in the list before chasing the event.
    2. 2Inspect the transmission filter and replace it if plugged.
    3. 3Test the transmission filter bypass switch with a meter to see whether it is stuck closed.
    4. 4Test the transmission harness for a short to ground on the bypass signal wire.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Cat CID 342 FMI 08Secondary engine speed sensor signal abnormal

    The ECM lost the secondary speed/timing signal for two seconds.· Erratic or implausible
    Check soon

    Causes

    • Open in the engine control harness to the cam sensor
    • Faulty secondary (camshaft) speed sensor
    • Engine ECM

    Checks

    1. 1Start the engine with Cat ET connected and confirm 342-8 is active.
    2. 2Switch off and test the secondary speed sensor circuit for an open.
    3. 3Inspect the cam sensor connector for oil or loose pins.
    4. 4Compare with 190-8; if only 342-8 is active the primary signal is fine.
    5. 5Replace the secondary sensor, then repair the harness or replace the ECM if needed.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Cat E362Engine overspeed

    The engine ECM saw engine speed above 3000 rpm for more than 0.6 seconds.· Real condition
    Check soon

    Causes

    • Machine overrun downhill driving the engine
    • Wrong gear selection
    • Engine speed sensor fault

    Checks

    1. 1Connect Cat ET and check E361 and other diagnostic codes first.
    2. 2Check whether other active diagnostic codes exist and repair them.
    3. 3Review operating practice and gear selection on grades.
    4. 4The manual treats E362 as informational once nothing else is active.
    5. 5Reduce engine speed and operation and re-check.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Cat CID 549 FMI 02Throttle lock mode switch data erratic

    The engine ECM sees an erratic, intermittent or incorrect signal from the throttle lock mode switch.· Erratic or implausible
    Check soon

    Causes

    • Throttle lock enable switch faulty
    • Open or shorted engine wiring harness
    • Open or shorted lower cab wiring harness
    • Engine ECM (rare)

    Checks

    1. 1Connect Cat ET and watch the throttle lock switch status while pressing the switch.
    2. 2Check the switch connector in the cab for pin contact and corrosion.
    3. 3Run open and short tests on the engine and lower cab harness sections of the circuit.
    4. 4Replace the switch if the harness is good, then rerun and confirm the code clears.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

Shared checks

Checks, in order

  1. 1Check the J1939 data link wiring and terminating resistors between the ECMs for opens and shorts.
  2. 2Inspect each speed sensor and connector for oil, damage and the correct air gap.
  3. 3Check battery voltage first, because low supply voltage can corrupt ECM data.
  4. 4Replace the filter named in the event and clear it in Cat ET.
  5. 5Operate the throttle lock mode switch and watch its state in Cat ET for erratic changes.
  6. 6Test the sensor circuits for open and short with a multimeter.
  7. 7Flash the correct personality file with Cat ET and recheck the codes.

Causes

  • J1939 data link wiring or terminator fault
  • Damaged speed sensor or wrong air gap
  • Wrong or corrupt flash file
  • Dirty or plugged filter element

Most common here: erratic or implausible (5 of 11)

Watch the live value on the service tool while you flex the harness and tap the connector.

When to stop

You'll notice: A hard start or no-start, a rough engine or a jumping tachometer.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.