JLG fault codes
JLG machines with the JLG Control System flash a two-part code (2-5, 3-3) on the platform and ground controls and log a numbered DTC (0010, 2211) in the analyzer. Both are listed here, from JLG service manuals 3120840 and 3121298.
259 codes in 13 families28 stop now, 215 check soon, 16 info
259 JLG codes - type a code, or a word from the problem.
Covers Boom lifts, Scissor lifts.
Where to look
- 01Turn the key on and watch the fault lamp or platform display.
- 02For the full detail connect a JLG Analyzer at the ground control or platform…
- 03Write down the Help message, not just the flash code.
- 04Fix the cause, then pull out and reset the red EMS button at the ground station to…
- 05If it returns right away, check the Help message again, as the wiring or part named…
How to read JLG fault codes, in full
- Turn the key on and watch the fault lamp or platform display: the lamp flashes the first digit, pauses, then the second (2 flashes then 1 flash = 2-1).
- For the full detail connect a JLG Analyzer at the ground control or platform connection point and open the Help screen to read the text message and DTC.
- Write down the Help message, not just the flash code: one flash code covers many different faults (3-3 alone covers dozens of outputs).
- Fix the cause, then pull out and reset the red EMS button at the ground station to clear latched faults.
- If it returns right away, check the Help message again, as the wiring or part named in it is the real target.
How urgent is a JLG code?
- Stop now28 codes
- Shut down and fix before working on. Running on risks damage or the machine locks out.
- Check soon215 codes
- The machine may derate or limit a function. Find the cause before the next shift.
- Information16 codes
- A reminder or status message. Nothing is failing yet.
Pick your system
Find the part of the machine, then the family your code belongs to.
- Code range
- The first and last code in the family, as the machine shows them.
- Codes
- How many codes the family holds; each is explained on its page.
- Severity mix
- The share of stop, check and info codes. The dot after it is the most urgent one in the family.
Platform / ground controls51 codes
Status17 codes
Load sensing19 codes
Engine15 codes
Electrical22 codes
Outputs (valves and coils)112 codes
- Throttle, fuel actuator and LP gas solenoids3352 – 3313215 codes
- Main lift, swing and tower lift valves and current334 – 3342521 codes
- Telescope and jib lift valves3415 – 3319018 codes
- Platform level and platform rotate valves3-4 – 341424 codes
- Drive, steer and flow control valves8639 – 3341918 codes
- Drive brake, traction lock, oscillating axle and dump valves3-5 – 3342416 codes
Controller22 codes
Hydraulic1 code
Most searched JLG codes
- 2-1Footswitch or keyswitch fault
- 2-2Drive or steer selection fault
- 2-3Boom function selection fault
- 2-5Function prevented by cutout
- 2-8Hydraulic filter bypassed
- 3-3Driver (output) short or open circuit
- 4-2Engine over temperature
- 4-3Engine fault
- 4-4Battery supply problem
- 6-6CAN bus failure
- 9-9Controller (module) problem
- 0010Running at cutback - out of transport position
- 212Keyswitch faulty
- 213Footswitch faulty
- 331Brake - short to battery
- 332Brake - open circuit
- 438High engine temperature
- 441Battery voltage too low - system shutdown
- 442Battery voltage too high - system shutdown
- 445Battery voltage low (warning)
- 662CAN bus failure - platform module
- 813Chassis tilt sensor not calibrated
- 2211Footswitch interlock tripped
- 4310No alternator output
- 4311Low oil pressure
- 9921Ground module failure - high side driver cutout faulty
- 9922Platform module failure - HWFS code 1
Quick answers
How do I read JLG fault codes?
Turn the key on and watch the fault lamp or platform display: the lamp flashes the first digit, pauses, then the second (2 flashes then 1 flash = 2-1). For the full detail connect a JLG Analyzer at the ground control or platform connection point and open the Help screen to read the text message and DTC.
Which JLG codes mean stop now?
28 of the 259 JLG codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example 4-2, 6-6, 9-9, 331. 215 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.
What should I check first on a JLG code?
Most JLG codes here (44 of 259) read as shorted low: the signal sits at or near zero volts - less than a working sensor can send. First test, as general workshop practice: key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Sources
Every code was read from these documents and written in our own words.
Other makers
Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.
Post a request