JLG · Status
JLG Cutouts, reduced speed, overload and status messages fault codes
These are messages in which the controller is not reporting a broken part but limiting the machine: reduced drive speed (creep and cutback), function cutouts and prevented functions, platform overload from the load sensing system, and general system status messages. They tell you which protection is active and why.
Where this code shows
Turn the key on and watch the fault lamp or platform display.
What do these codes mean?
JLG codes 001 to 2518 are all about the cutouts, reduced speed, overload and status messages. The most common failure type is real condition (6 of 17); none needs an immediate stop. Start with this check: read the message and note which function is limited.
How urgent are they?
None of the 17 codes here means stop now; 3 can wait until the shift ends, but find the cause before the next one; 14 are information only.
- Check soon3
- Info14
What should I check first?
Read the message and note which function is limited
Shared checks17 of 17
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Running at cutback1 code
JLG 0010Running at cutback: Out of transport position
Not a fault. The machine is running at cutback because the boom is out of its transport (stowed) position, so drive and function speeds are reduced. The operator notices the machine slower than normal while the boom is raised or extended.· OtherOtherInfoCauses
- Boom raised or extended past the stowed position, which is normal operation
- Transport or elevation switch not reading stowed when the boom is actually stowed
- Proximity sensor or switch target out of gap after a knock
- Transport switch harness damaged or connector loose
- Cutback configured for the market or model
Checks
- 1Lower and retract the boom fully to the stowed position and see whether the message clears
- 2Check the transport switch or proximity sensor and look for a damaged target or a gap that has moved
- 3Watch the transport input in the analyzer diagnostics while the boom is stowed; it should change state when the boom leaves the stowed position
- 4Inspect the wiring and connector at the switch for chafing, water and loose pins
- 5Confirm the cutback setting in the machine configuration if the behaviour is unexpected
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Running at creep4 codes
JLG 0012Running at creep: Creep switch open
The creep switch input reads open, so the controller holds the machine at creep speed. Normal speed returns once that input is in the state the machine expects.· OtherOtherInfoCauses
- Creep switch genuinely open for the current machine position
- Creep switch wire broken or its connector loose
Checks
- 1Read the creep switch input in the analyzer and operate the switch to see it change
- 2Check the switch wiring and plug if the input stays open with the machine in the normal position
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JLG 0013Running at creep: Tilted and above elevation
Boom functions are limited to creep speed because the machine is tilted beyond its set angle while the boom is above elevation. The operator finds the boom crawling and may not be able to continue until the machine is levelled.· OtherOtherInfoCauses
- Machine standing on a slope steeper than the tilt setting
- Chassis tilt sensor out of calibration
- Tilt angle configuration set too tight for the model
- Tilt sensor loose on its mount so it reads off
Checks
- 1Lower the boom and move the machine to firm level ground, then retry the function
- 2Read the tilt value in the analyzer and compare with a spirit level or inclinometer on the chassis
- 3Check that the tilt sensor is bolted down square and that its connector is clean and fully seated
- 4Recalibrate the chassis tilt sensor with the analyzer on level ground if the reading is off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JLG 0030Running at creep: Platform stowed
The controller is holding the machine at creep speed in connection with the platform stowed condition. Normal speed returns once the stowed input is in the state the machine expects.· OtherOtherInfoCauses
- Platform or boom really in the stowed position
- Stowed position switch misadjusted or stuck
Checks
- 1Check the stowed position input in the analyzer against the real position of the platform
- 2Adjust or replace the stowed switch and check its wiring if the input is wrong
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JLG 826Running at creep: Platform overloaded
The load sensing system finds the platform above its rated load, so the controller holds the machine at creep speed. Taking weight out of the platform normally brings normal speed back.· Real conditionReal conditionCheck soonCauses
- Platform genuinely carrying more than its rated load
- Load cells out of calibration so the weight reads high
Checks
- 1Take load off the platform and see whether the message clears
- 2Compare the weight shown in the analyzer with the real load
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Model changed - hydraulics suspended1 code
JLG 259Model changed - hydraulics suspended: Cycle EMS
The machine model setting was changed, so the controller suspends the hydraulic functions until power is cycled with the new setting loaded. It is a request to restart, not a hardware fault.· OtherOtherInfoCauses
- Machine model changed in the analyzer settings
- Personality or settings reloaded without restarting the machine
Checks
- 1Cycle EMS to load the new model setting
- 2Confirm in the analyzer that the model setting matches the machine plate, and correct it if wrong
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Remote contract management override1 code
JLG 681Remote contract management override: All functions in creep
A remote contract management command is holding every function at creep speed. The override comes from outside the machine, usually from the fleet or rental system, not from a faulty part.· OtherOtherInfoCauses
- Fleet or rental system set the override, for example for an expired or locked contract
- Telematics unit fitted and sending the command
Checks
- 1Contact the machine owner or fleet manager to have the override lifted
- 2If no such system is used, check the telematics module and its wiring for a false command
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Drive & boom prevented1 code
JLG 827Drive & boom prevented: Platform overloaded
The platform is overloaded enough that the controller blocks both drive and boom functions. Reducing the platform load is the first step before looking for a sensor fault.· Real conditionReal conditionCheck soonCauses
- Platform overloaded with people or material
- Load sensing calibration lost or a cell reading high
Checks
- 1Remove load until the message clears and drive and boom return
- 2If the platform is empty, read each cell value and recalibrate the system
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Lift up & tele out prevented1 code
JLG 828Lift up & tele out prevented: Platform overloaded
The platform is overloaded, so the controller blocks boom lift up and telescope out, the moves that increase the load on the structure. Lift down and telescope in normally still work so the platform can be lowered.· Lost messageLost messageCheck soonCauses
- Platform overloaded
- Load sensing system reading high from a damaged cell or lost calibration
Checks
- 1Use lift down and telescope in to bring the platform to a safe position, then remove load
- 2If it is empty, check the cell values and calibration in the analyzer
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Boom prevented1 code
JLG 2514Boom prevented: Drive selected
Boom functions are blocked because a drive function is selected, so the operator must release drive before moving the boom.· Real conditionReal conditionInfoCauses
- Drive stick off centre while a boom function is selected
- Drive stick not returning to neutral
Checks
- 1Release the drive stick and select the boom function again
- 2Check the drive stick returns to centre and reads neutral in the analyzer
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Drive prevented3 codes
JLG 2516Drive prevented: Above elevation
Drive is blocked because the boom is raised above the elevation limit. Lowering the boom restores drive.· Real conditionReal conditionInfoCauses
- Boom above the permitted elevation for driving
- Elevation sensor or switch reading wrongly
Checks
- 1Lower the boom below the limit and try drive again
- 2Compare the elevation input in the analyzer with the real boom angle
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JLG 2517Drive prevented: Tilted & above elevation
Drive is blocked because the machine is tilted and the boom is above the elevation limit at the same time. Lowering the boom or levelling the machine restores drive.· Real conditionReal conditionInfoCauses
- Machine on a slope with the boom raised
- Tilt or elevation sensor reading wrongly
Checks
- 1Lower the boom and move to level ground
- 2Check the tilt and elevation readings in the analyzer against reality
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JLG 2518Drive prevented: Boom selected
Drive is blocked because a boom function is selected, so the operator must release the boom stick before driving.· Real conditionReal conditionInfoCauses
- Boom stick off centre while drive is selected
- Boom switch not returning to neutral
Checks
- 1Release the boom stick and select drive again
- 2Check the boom control returns to neutral and reads zero in the analyzer
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Other codes4 codes
JLG 001Everything OK
The analyzer shows this Help line when the controller has no active fault: the modules are talking and no input or output check has failed. It is a status line, not a fault, so nothing needs repairing.· OtherOtherInfoCauses
- Normal healthy state with no fault active
- An earlier fault cleared itself or was cleared with the EMS button
Checks
- 1If the machine still misbehaves, open the fault log in the analyzer, since this line only shows the live state
- 2Confirm the analyzer is connected to the module you meant to read
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JLG 2-5Function prevented by cutout
Not a failure. The controller blocks a function on purpose because a cutout is set: drive while elevated, boom while driving, or drive while tilted and above elevation.· OtherOtherInfoCauses
- Drive selected while the boom is above elevation with drive cutout configured
- Boom function selected while driving with the no-simultaneous-drive cutout active
- Chassis tilted past the set angle while above elevation
- Function cutout configuration digit set for CE or a special market
Checks
- 1Read the Help message: DRIVE PREVENTED or BOOM PREVENTED
- 2Lower or stow the boom, level the machine, then try again
- 3Check configuration digit 16 (function cutout) matches the machine spec
- 4Confirm the tilt switch and elevation (transport) switch read correctly in diagnostics
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JLG 211Power cycle
The controller reports that power was cycled, or that it needs a power cycle before it carries on. The manual lists it as a message with no further fault text.· OtherOtherInfoCauses
- Key or red EMS button switched off and on
- Supply interrupted by a loose battery lead or poor connection
Checks
- 1Cycle the key and EMS once and see whether the message comes back
- 2If it returns by itself, check the battery terminals and the main ground for looseness
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JLG 2513Generator motion cutout active
A cutout is active that stops machine motion while the generator is in use, so drive and boom will not move until the generator mode is switched off.· OtherOtherInfoCauses
- Generator or auxiliary power mode left switched on
- Generator mode input stuck active
Checks
- 1Switch the generator mode off and see whether motion returns
- 2Check the generator input state in the analyzer and the switch wiring
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Read the message and note which function is limited
- 2Check whether the limit input in the analyzer matches the real position of the boom or platform
- 3Remove load from the platform and see whether an overload message clears
- 4Look for other active codes first, since a restriction often follows a fault
- 5Clear the cause and cycle EMS to confirm the limit is released
Causes
- A limit switch, tilt or boom position input that has reached its limit
- Platform loaded beyond its rating or load cells reading wrongly
- An active fault elsewhere that makes the controller restrict functions
- Operator working outside the allowed envelope
Most common here: real condition (6 of 17)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: The machine still runs but a function is slowed, cut out or prevented, and a message or flash code says so.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- JLG 600S/660SJ Service and Maintenance Manual 3121298, section 6 (Table 6-8 Fault Code List)
- JLG 600S/600SJ/660SJ/600A/AJ Service and Maintenance Manual 3120840, section 6 (Tables 6-3, 6-5)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
