Bobcat fault codes
Bobcat loaders and excavators show a service code on the display: M followed by four digits on M- and R-series machines, or a two-digit pair such as 03-09 on older ones. The first digits name the system, the last two the fault.
1,258 codes in 45 families51 stop now, 1,177 check soon, 30 info
1258 Bobcat codes - type a code, or a word from the problem.
- LOWVLTGLow battery voltageOther
- VRLOWVLTGVery low battery voltageOther
- VSE001-00Oil temp. sensor, signal above normal rangeReal condition
- VSP001-02Front pump press. sensor, incorrect signalOther
- VAL001-03Alternator potential, voltage above normalShorted high
- VSE001-03Oil temp. sensor, voltage above normalShorted high
- VSP001-03Front pump press. sensor, voltage above normalShorted high
- VAL001-04Alternator potential, voltage below normalShorted low
- VSE001-04Oil temp. sensor, voltage below normalShorted low
- VSP001-04Front pump press. sensor, voltage below normalShorted low
- VPV001-05Pump P/V (a), current below normalOpen circuit
- VRY001-05Glow plug relay, current below normalOpen circuit
- VSV001-05Breaker operating s/v, current below normalOpen circuit
- VPV001-06Pump P/V (a), current above normalShorted low
- VRY001-06Glow plug relay, current above normalShorted low
- VSV001-06Breaker operating s/v, current above normalShorted low
- VCO001-11Gauge panel errorOther
- 01-16Air filter not connectedOpen circuit
- 01-17Air filter pluggedReal condition
- VSP002-02Rear pump press. sensor, incorrect signalOther
- VSE002-03Fuel sensor, voltage above normalShorted high
- VSP002-03Rear pump press. sensor, voltage above normalShorted high
- VSE002-04Fuel sensor, voltage below normalShorted low
- VSP002-04Rear pump press. sensor, voltage below normalShorted low
- VAL002-05Accel. pedal switch, current below normalOpen circuit
- VPV002-05Pump P/V (b), current below normalOpen circuit
- VRY002-05Back buzzer relay, current below normalOpen circuit
- VSV002-05Relief press. up S/V (b), current below normalOpen circuit
- VAL002-06Accel. pedal switch, current above normalShorted low
- VPV002-06Pump P/V (b), current above normalShorted low
- VRY002-06Back buzzer relay, current above normalShorted low
- VSV002-06Relief press. up S/V (b), current above normalShorted low
- VCO002-11E-ECU errorOther
- 02-16Hydraulic charge filter not connectedOpen circuit
- 02-17Hydraulic charge filter pluggedLost message
- VSP003-02OWD press. sensor, incorrect signalOther
- VSE003-03Vehicle speed sensor, voltage above normalShorted high
- VSP003-03OWD press. sensor, voltage above normalShorted high
- VSE003-04Vehicle speed sensor, voltage below normalShorted low
- VSP003-04OWD press. sensor, voltage below normalShorted low
- VPV003-05Flow control P/V (g), current below normalOpen circuit
- VRY003-05Backup lamp relay, current below normalOpen circuit
- VSV003-05High speed S/V (c), current below normalOpen circuit
- VPV003-06Flow control P/V (g), current above normalShorted low
- VRY003-06Backup lamp relay, current above normalShorted low
- VSV003-06High speed S/V (c), current above normalShorted low
- 03-09Battery voltage lowShorted low
- 03-10Battery voltage highShorted high
- 03-11Battery voltage extremely highShorted high
- 03-14Battery voltage extremely lowShorted low
- 03-22Battery voltage out of range lowOther
- VSE004-01WIF sensor, signal below normal rangeReal condition
- VSE004-03WIF sensor, voltage above normalShorted high
- VSP004-03Px(front) press. sensor, voltage above normalShorted high
- VSE004-04WIF sensor, voltage below normalShorted low
- VSP004-04Px(front) press. sensor, voltage below normalShorted low
- VPV004-05Fan control P/V (j), current below normalOpen circuit
- VRY004-05Inching relay, current below normalOpen circuit
- VSV004-05Reverse fan S/V (d), current below normalOpen circuit
- VPV004-06Fan control P/V (j), current above normalShorted low
- VRY004-06Inching relay, current above normalShorted low
- VSV004-06Reverse fan S/V (d), current above normalShorted low
- 04-09Engine oil pressure lowOther
- 04-14Engine oil pressure extremely lowLost message
- 04-15Engine oil pressure shutdown levelOther
- 04-21Engine oil pressure out of range highOther
- 04-22Engine oil pressure out of range lowOther
- VSE005-03Spare speed, voltage above normalShorted high
- VSP005-03Pressure sensor issueOther
- VSE005-04Spare speed, voltage below normalShorted low
- VSP005-04Py(travel) press. sensor, voltage below normalShorted low
- VPV005-05Press. control 1 P/V (h), current below normalOpen circuit
- VRY005-05Low speed relay, current below normalOpen circuit
- VSV005-05Travel II pump confluence s/v, current below normalOpen circuit
- VPV005-06Press. control 1 P/V (h), current above normalShorted low
- VRY005-06Low speed relay, current above normalShorted low
- VSV005-06Travel II pump confluence s/v, current above normalShorted low
- 05-09Hydraulic charge pressure lowReal condition
- 05-14Hydraulic charge pressure extremely lowOther
- 05-15Hydraulic charge pressure shutdown levelReal condition
- 05-21Hydraulic charge pressure out of range highOther
- 05-22Hydraulic charge pressure out of range lowOther
- VSE006-03Spare, voltage above normalShorted high
- VSP006-03Boom up press. sensor, voltage above normalShorted high
- VSE006-04Spare, voltage below normalShorted low
- VSP006-04Boom up press. sensor, voltage below normalShorted low
- VPV006-05Press. control 2 P/V (i), current below normalOpen circuit
- VRY006-05High speed relay, current below normalOpen circuit
- VSV006-05Swing brake release S/V (k), current below normalOpen circuit
- VPV006-06Press. control 2 P/V (i), current above normalShorted low
- VRY006-06High speed relay, current above normalShorted low
- VSV006-06Swing brake release S/V (k), current above normalShorted low
- 06-10Engine speed highLost message
- 06-11Engine speed extremely highOther
- 06-13Engine speed no signalOther
- 06-15Engine speed shutdown levelReal condition
- 06-18Engine speed out of rangeOther
- VSE007-03Angle sensor (a), voltage above normalShorted high
- VSP007-03Bucket crowd press. sensor, voltage above normalShorted high
- VSE007-04Angle sensor (a), voltage below normalShorted low
- VSP007-04Bucket crowd press. sensor, voltage below normalShorted low
- VPV007-05Flow control P/V (c) 2-way rh-open, current below normalOpen circuit
- VRY007-05Starter relay, current below normalOpen circuit
- VSV007-05Option safety s/v, current below normalOpen circuit
- VPV007-06Flow control P/V (c) 2-way rh-open, current above normalShorted low
- VRY007-06Starter relay, current above normalShorted low
- VSV007-06Option safety s/v, current above normalShorted low
- 07-10Hydraulic oil temperature highOther
- 07-11Hydraulic oil temperature extremely highOther
- 07-15Hydraulic oil temperature shutdown levelOther
- 07-21Hydraulic oil temperature out of range highOther
- 07-22Hydraulic oil temperature out of range lowOther
- VSE008-03Angle sensor (b), voltage above normalShorted high
- VSP008-03Boom down press. sensor, voltage above normalShorted high
- VSE008-04Angle sensor (b), voltage below normalShorted low
- VSP008-04Boom down press. sensor, voltage below normalShorted low
- VPV008-05Flow control P/V (d) 2-way rh-close, current below normalOpen circuit
- VRY008-05Glow plug II relay, current below normalOpen circuit
- VSV008-05Cruise S/V (f), current below normalOpen circuit
- VPV008-06Flow control P/V (d) 2-way rh-close, current above normalShorted low
- VRY008-06Glow plug II relay, current above normalShorted low
- VSV008-06Cruise S/V (f), current above normalShorted low
- 08-10Engine coolant temperature highOther
- 08-11Engine coolant temperature extremely highOther
- 08-15Engine coolant temperature shutdown levelOther
- 08-21Engine coolant temperature out of range highOther
- 08-22Engine coolant temperature out of range lowOther
- VSP009-03Bucket dump press. sensor, voltage above normalShorted high
- VSP009-04Bucket dump press. sensor, voltage below normalShorted low
- VPV009-05Flow control P/V (e) rotating cw, current below normalOpen circuit
- VSV009-05Forward S/V (g), current below normalOpen circuit
- VPV009-06Flow control P/V (e) rotating cw, current above normalShorted low
- VSV009-06Forward S/V (g), current above normalShorted low
- 09-09Fuel level lowOther
- 09-21Fuel level out of range highOther
- 09-22Fuel level out of range lowOther
- B10BC-F0Drive right input not in neutralErratic or implausible
- B10B0-00Drive ISO/H pattern switch flipped while operatingOther
- C10B0-00Workgroup disabled due to window faultOther
- C10C0-F0Right swash plate not in neutralErratic or implausible
- U10A0-08Drive motor case drain hydraulic oil temperature sensor no communicationLost message
- U10B0-08Left joystick base message failureOther
- U10D0-08Remote control no communicationLost message
- B10A0-12Wiper output short to batteryShorted high
- B10D0-12Display switched power relay error onOther
- B10A0-14Wiper output short to ground or open circuitShorted low
- B10D0-14Display switched power relay error offShorted low
- C10A0-16Drive motor case drain hydraulic oil temperature out of range lowOther
- C10A0-17Drive motor case drain hydraulic oil temperature out of range highOther
- U10B0-49Left joystick base failureOther
- U10C0-49Right joystick base failureOther
- C10D0-54Drive pump not calibratedLost message
- C10C0-77Right swash plate commanded position not reachableOther
- U10D0-93Remote control loss communicationLost message
- C10A1-FADrive motor case drain hydraulic oil temperature highLost message
- C10A1-FBDrive motor case drain hydraulic oil temperature extremely highOther
- C10A1-FCDrive motor case drain hydraulic oil temperature reduced performanceOther
- B10B1-F0Drive input not in neutralErratic or implausible
- U10B1-08Left joystick grip message failureOther
- U10C1-08Right joystick grip message failureOther
- B10A1-12Washer fluid output short to batteryShorted high
- B10A1-14Washer fluid output short to ground or open circuitShorted low
- C10C1-16Right swash plate sensor out of range lowShorted low
- C10C1-17Right swash plate sensor out of range highShorted high
- U10B1-49Left joystick grip failureOther
- U10C1-49Right joystick grip failureOther
- U10B2-49Left joystick failureOther
- U10C2-49Right joystick failureOther
- VSP010-03Arm in press. sensor, voltage above normalShorted high
- B10B3-F0Drive x input not in neutralErratic or implausible
- U10B3-00Left joystick multipleOther
- U10C3-00Right joystick multipleOther
- VSP010-04Arm in press. sensor, voltage below normalShorted low
- VPV010-05Flow control P/V (f) rotating ccw, current below normalOpen circuit
- VSV010-05Reverse S/V (h), current below normalOpen circuit
- C10C5-F0Left swash plate not in neutralOther
- U10A5-08Pump case drain hydraulic oil temperature sensor no communicationLost message
- C10A5-16Pump case drain hydraulic oil temperature out of range lowOther
- C10A5-17Pump case drain hydraulic oil temperature out of range highOther
- C10C5-77Left swash plate commanded position not reachableOther
- C10A6-FAPump case drain hydraulic oil temperature highLost message
- C10A6-FBPump case drain hydraulic oil temperature extremely highOther
- C10A6-FCPump case drain hydraulic oil temperature highLost message
- VPV010-06Flow control P/V (f) rotating ccw, current above normalShorted low
- VSV010-06Reverse S/V (h), current above normalShorted low
- B10B6-F0Drive y input not in neutralErratic or implausible
- C10C6-16Left swash plate sensor out of range lowOther
- C10C6-17Left swash plate sensor out of range highOther
- B10B9-F0Drive left input not in neutralErratic or implausible
- 10-16Hydraulic implement filter not connectedOpen circuit
- 10-17Hydraulic implement filter pluggedLost message
- C11C0-11Left forward drive solenoid error offShorted low
- C11C0-12Left forward drive solenoid error onOther
- C11C2-11Left reverse drive solenoid error offShorted low
- C11C2-12Left reverse drive solenoid error onOther
- VSP011-03Arm out press. sensor, voltage above normalShorted high
- VSP011-04Arm out press. sensor, voltage below normalShorted low
- C11C4-11Right forward drive solenoid error offOther
- C11C4-12Right forward drive solenoid error onOther
- 11-05Seat bar sensor short to batteryShorted high
- VPV011-05Travel, current below normalOpen circuit
- VSV011-052 pump select S/V (i), current below normalOpen circuit
- 11-06Seat bar sensor short to groundShorted low
- VPV011-06Travel, current above normalShorted low
- VSV011-062 pump select S/V (i), current above normalShorted low
- C11C6-11Right reverse drive solenoid error offOther
- C11C6-12Right reverse drive solenoid error onOther
- VSP012-03Travel press. sensor(lh), voltage above normalShorted high
- VSP012-04Travel press. sensor(lh), voltage below normalShorted low
- VPV012-05Travel straight P/V (l), current below normalOpen circuit
- VSV012-05Bypass cut off S/V (j), current below normalOpen circuit
- VPV012-06Travel straight P/V (l), current above normalShorted low
- VSV012-06Bypass cut off S/V (j), current above normalShorted low
- 12-21Front auxiliary PWM switch out of range highShorted high
- 12-22Front auxiliary PWM switch out of range lowShorted low
- 12-23Front auxiliary PWM switch not in neutralErratic or implausible
- VSP013-03Travel press. sensor(rh), voltage above normalShorted high
- VSP013-04Travel press. sensor(rh), voltage below normalShorted low
- 13-05Fuel shut-off hold solenoid short to batteryShorted high
- 13-06Fuel shut-off hold solenoid short to groundShorted low
- 13-07Fuel shut-off solenoid open circuitOpen circuit
- 14-02Fuel shut-off pull solenoid error ONOther
- 14-03Fuel shut-off pull solenoid error OFFOther
- VSP014-03Swing press. sensor, voltage above normalShorted high
- VSP014-04Swing press. sensor, voltage below normalShorted low
- 15-02Traction lock pull solenoid error ONOther
- 15-03Traction lock pull solenoid error OFFOther
- VSP015-03Att(option) press. sensor, voltage above normalShorted high
- VSP015-04Att(option) press. sensor, voltage below normalShorted low
- VSP016-03Attachment 2 press. sensor, voltage above normalShorted high
- VSP016-04Attachment 2 press. sensor, voltage below normalShorted low
- 16-05Traction lock hold solenoid short to batteryShorted high
- 16-06Traction lock hold solenoid short to groundShorted low
- 16-07Traction lock hold solenoid open circuitOpen circuit
- VSP017-03Option pedal 1 press. sensor, voltage above normalShorted high
- VSP017-04Option pedal 1 press. sensor, voltage below normalShorted low
- 17-05Hydraulic lock valve solenoid short to batteryShorted high
- 17-06Hydraulic lock valve solenoid short to groundShorted low
- 17-07Hydraulic lock valve solenoid open circuitOpen circuit
- VSP018-03Option pedal 2 press. sensor, voltage above normalShorted high
- VSP018-04Option pedal 2 press. sensor, voltage below normalShorted low
- 18-05Spool lock solenoid short to batteryShorted high
- 18-06Spool lock solenoid short to groundShorted low
- 18-07Spool lock solenoid open circuitOpen circuit
- 19-02Bucket position solenoid error onOther
- 19-03Bucket position solenoid error offShorted low
- 20-02Two-speed solenoid error ONOther
- 20-03Two-speed solenoid error OFFOther
- 21-02Glow plug error onShorted high
- 21-03Glow plug error OFFOther
- 22-02Starter error ONOther
- 22-03Starter error OFFOther
- 23-02Rear base solenoid error onOther
- 23-03Rear base solenoid error offShorted low
- 24-02Rear rod solenoid error onOther
- 24-03Rear rod solenoid error offOther
- 25-02Rear auxiliary relief solenoid error onOther
- 25-03Rear auxiliary relief solenoid error offShorted low
- 26-02Front base solenoid error onOther
- 26-03Front base solenoid error offShorted low
- 27-02Front rod solenoid error onOther
- 27-03Front rod solenoid error offOther
- 28-02Diverter solenoid error onLost message
- 28-03Diverter solenoid error offShorted low
- 29-02High flow solenoid error ONShorted high
- 29-03High flow solenoid error OFFShorted high
- 30-28Controller memory failurePart or controller
- 31-28Interrupted power failurePart or controller
- 32-04ACS not communicating with bobcat controllerLost message
- 32-23ACS not calibratedPart or controller
- 32-31Tilt actuator faultOther
- 32-32Tilt actuator wiring faultOther
- 32-33Tilt handle wiring faultOther
- 32-34Tilt actuator not in neutralReal condition
- 32-35Tilt handle / pedal not in neutralErratic or implausible
- 32-36Lift actuator faultOther
- 32-37Lift actuator wiring faultOther
- 32-38Lift handle wiring faultOther
- 32-39Lift actuator not in neutralReal condition
- 32-40Lift handle / pedal not in neutralOther
- 32-41ACS no communicationLost message
- 32-49Lift actuator short to groundShorted low
- 32-50Tilt actuator short to groundShorted low
- 32-51Lift actuator short to batteryShorted high
- 32-52Tilt actuator short to batteryShorted high
- 32-53Lift handle / pedal short to groundShorted low
- 32-54Tilt handle / pedal short to groundShorted low
- 32-55Lift handle / pedal short to batteryShorted high
- 32-56Tilt handle / pedal short to batteryShorted high
- 32-57Lift actuator reduced performanceOther
- 32-58Tilt actuator reduced performanceOther
- 32-59Lift actuator wrong directionOther
- 32-60Tilt actuator wrong directionOther
- 32-61Handle lock short to groundShorted low
- 32-62Handle lock short to batteryShorted high
- 32-63Pedal lock short to groundShorted low
- 32-64Pedal lock short to batteryShorted high
- 32-65Sensor supply voltage out of rangeOther
- 32-66Battery voltage out of rangeOther
- 32-67Switch flipped while operatingOther
- 32-68Lift handle information errorOther
- 32-69Control pattern switch flipped while operatingOther
- 32-70Right drive handle short to groundShorted low
- 32-71Right drive handle short to batteryShorted high
- 33-23Main controller not programmedPart or controller
- 34-04Keyless panel no communication to Bobcat controllerLost message
- 35-02Two-speed fan error onOther
- 35-03Two-speed fan error offShorted low
- 36-48ACD multiple controllers presentOther
- 37-02Two-speed secondary error onShorted high
- 37-03Two-speed secondary error offShorted low
- U100A-08Machine control message failureOther
- C100A-11ECU power short to groundShorted low
- P100A-11Starter output short to groundShorted low
- C100A-12ECU power short to batteryShorted high
- P100A-12Starter output short to batteryShorted high
- C100A-13ECU power open circuitOpen circuit
- P100A-13Starter output open circuitOpen circuit
- P100B-16Starter output error offShorted low
- P100B-17Starter output error onShorted high
- C101D-16Tilt rod pressure sensor out of range lowOther
- C101D-17Tilt rod pressure sensor out of range highOther
- L0102Standard panel button 1 error onLost message
- C102B-11Reverse fan short to groundShorted low
- C102B-12Reverse fan short to batteryShorted high
- C102B-13Reverse fan open circuitOpen circuit
- B102A-16Cab controller sensor supply voltage out of range lowOther
- B102A-17Cab controller sensor supply voltage out of range highOther
- C103A-11Ride control 1 short to groundShorted low
- C103B-11Ride control 2 short to groundShorted low
- C103C-11Bob-Tach engage short to groundShorted low
- C103D-11Bob-Tach disengage short to groundShorted low
- C103A-12Ride control 1 short to batteryShorted high
- C103B-12Ride control 2 short to batteryShorted high
- C103C-12Bob-Tach engage short to batteryShorted high
- C103D-12Bob-Tach disengage short to batteryShorted high
- C103A-13Ride control 1 open circuitOpen circuit
- C103B-13Ride control 2 open circuitOpen circuit
- C103C-13Bob-Tach engage open circuitOpen circuit
- C103D-13Bob-Tach disengage open circuitOpen circuit
- H0104Boom angle sensor no communicationLost message
- C104A-00Lift float failed to achieve floatOther
- C104B-00Lift float conditions not favorableOther
- C104C-00Lift float failed to maintain floatOther
- U109C-A2Lights controller voltage lowShorted low
- U109C-A3Lights controller voltage highShorted high
- U109C-08Lights controller communication errorLost message
- U109C-51Lights controller not programmedOther
- U109C-57Lights controller software incompatiblePart or controller
- M0116Air filter switch not connectedOpen circuit
- B116F-11Front left road light short to groundShorted low
- B116F-12Front left road light short to batteryShorted high
- B116F-13Front left road light open circuitOpen circuit
- M0117Air filter pluggedReal condition
- B117F-11Front right road light short to groundShorted low
- B117F-12Front right road light short to batteryShorted high
- B117F-13Front right road light open circuitOpen circuit
- M0144Air filter derate level 1Real condition
- M0145Air filter derate level 2Real condition
- W0176Input selection flipped while operatingOther
- L0202Standard panel button 2 error onOther
- H0204Arm angle sensor no communicationLost message
- M0216Hydraulic/hydrostatic filter not connectedOpen circuit
- M0217Hydraulic/hydrostatic filter pluggedLost message
- P0225-54Throttle pedal position sensor calibration requiredPart or controller
- L0302Standard panel button 3 error onOther
- H0304Bucket angle sensor no communicationLost message
- M0309System voltage too lowShorted low
- M0310System voltage too highShorted high
- M0311System voltage extremely highShorted high
- M0314System voltage extremely lowOther
- W0321Battery voltage out of range highOther
- M0322System voltage out of range lowOther
- W0322Battery voltage out of range lowOther
- L0402Standard panel button 4 error onOther
- H0405Angle sensor supply short to batteryShorted high
- H0406Angle sensor supply short to groundShorted low
- H0407Angle sensor supply open circuitOpen circuit
- M0409Engine oil pressure too lowReal condition
- M0414Engine oil pressure extremely lowOther
- M0415Engine oil pressure shutdownOther
- M0421Engine oil pressure out of range highOther
- M0422Engine oil pressure out of range lowOther
- M0509Hydraulic charge pressure lowOther
- M0510Hydraulic charge pressure highOther
- M0511Hydraulic charge pressure extremely highLost message
- M0514Hydraulic charge pressure extremely lowOther
- M0515Hydraulic charge pressure shutdownOther
- M0521Hydraulic charge pressure out of range highOther
- W0521Lift spool position sensor out of range highOther
- M0522Hydraulic charge pressure out of range lowOther
- W0522Lift spool position sensor out of range lowOther
- W0524Lift spool position sensor not in neutralOther
- W0525Lift spool position sensor unresponsiveOther
- W0595Lift spool position sensor inverted movementOther
- M0610Engine speed too highReal condition
- M0611Engine speed extremely highReal condition
- M0613Engine speed no signalOther
- M0615Engine speed shutdownReal condition
- A0618Wheel speed out of rangeOther
- M0618Engine speed out of rangeOther
- W0621Tilt spool position sensor out of range highOther
- W0622Tilt spool position sensor out of range lowOther
- W0624Tilt spool position sensor not in neutralOther
- W0625Tilt spool position sensor unresponsiveOther
- M0634Engine speed invalid dataOther
- W0695Tilt spool position sensor inverted movementOther
- H0705Aux 4 base short to batteryShorted high
- H0706Aux 4 base short to groundShorted low
- H0707Aux 4 base open circuitOpen circuit
- M0710Hydraulic oil temperature too highReal condition
- M0711Hydraulic oil temperature extremely highOther
- M0715Hydraulic oil temperature shutdownOther
- M0721Hydraulic oil temperature out of range highOther
- M0722Hydraulic oil temperature out of range lowShorted low
- H0732Aux 4 base overcurrentReal condition
- H0805Aux 4 rod short to batteryShorted high
- H0806Aux 4 rod short to groundShorted low
- H0807Aux 4 rod open circuitOpen circuit
- M0810Engine coolant temperature too highReal condition
- M0811Engine coolant temperature extremely highReal condition
- M0815Engine coolant temperature shutdownOther
- M0821Engine coolant temperature out of range highReal condition
- M0822Engine coolant temperature out of range lowReal condition
- M0826Engine coolant temperature pre shutdownOther
- H0832Aux 4 rod overcurrentOther
- H0905Direct to tank short to batteryShorted high
- H0906Direct to tank short to groundShorted low
- H0907Direct to tank open circuitOpen circuit
- M0909Fuel level too lowReal condition
- M0921Fuel level out of range highOther
- M0922Fuel level out of range lowOther
- H0932Direct to tank overcurrentReal condition
- C1002-16Sensor supply out of range lowOther
- C1002-17Sensor supply out of range highOther
- W1005Lift base solenoid short to batteryShorted high
- B1005-00Key switch multipleOther
- W1006Lift base solenoid short to groundShorted low
- W1007Lift base solenoid open circuitOpen circuit
- U1011-08Options keypad no communicationLost message
- C1015-F0Lift spool position sensor not in neutralErratic or implausible
- C1015-16Lift spool position sensor out of range lowShorted low
- C1015-17Lift spool position sensor out of range highShorted high
- C1015-56Lift spool position sensor inverted movementErratic or implausible
- U1015-62Throttle encoder signal failureOther
- C1015-93Lift spool position sensor unresponsiveOpen circuit
- M1016Hydraulic charge filter not connectedOpen circuit
- C1016-F0Tilt spool position sensor not in neutralOther
- C1016-16Tilt spool position sensor out of range lowOther
- C1016-17Tilt spool position sensor out of range highOther
- C1016-93Tilt spool position sensor unresponsiveOther
- M1017Hydraulic charge filter pluggedLost message
- C1029-11Hydraulic lock solenoid short to groundShorted low
- C1029-12Hydraulic lock solenoid short to batteryShorted high
- C1029-13Hydraulic lock solenoid open circuitOpen circuit
- C1030-00Two speed shift not allowedOther
- B1030-11Front work light (left side) short to groundShorted low
- B1030-12Front work light (left side) short to batteryShorted high
- B1030-13Front work light (left side) not connectedOpen circuit
- B1031-11Front work light (right side) short to groundShorted low
- B1031-12Front work light (right side) short to batteryShorted high
- B1031-13Front work light (right side) not connectedOpen circuit
- W1032Lift base solenoid overcurrentReal condition
- C1032-11Brake pull output short to groundShorted low
- C1032-12Brake pull output short to batteryShorted high
- C1032-13Brake pull output open circuitOpen circuit
- C1033-11Left brake hold output short to groundShorted low
- C1033-12Left brake hold output short to batteryShorted high
- C1033-13Left brake hold output open circuitOpen circuit
- C1034-11Right brake hold output short to groundShorted low
- B1034-12Rear work lights error onOther
- C1034-12Right brake hold output short to batteryShorted high
- C1034-13Right brake hold output open circuitOpen circuit
- B1034-14Rear work lights error offShorted low
- B1035-12Rear marker light short to batteryShorted high
- B1035-14Rear marker light short to ground or open circuitShorted low
- C1035-16Left brake pull relay error offShorted low
- C1035-17Left brake pull relay error onShorted high
- B1036-12Rear tail lights error onOther
- B1036-14Rear tail lights error offShorted low
- C1036-16Right brake pull relay error offShorted low
- C1036-17Right brake pull relay error onShorted high
- B1037-12Stop lamp short to batteryShorted high
- B1037-14Stop lamp short to ground or open circuitShorted low
- B1038-12Registration plate lamp short to batteryShorted high
- B1038-14Registration plate lamp short to ground or open circuitShorted low
- B1039-11Side lights short to groundShorted low
- B1039-12Side lights short to batteryShorted high
- B1039-13Side lights not connectedOpen circuit
- C1039-19High flow solenoid overcurrentReal condition
- C1040-11Lift actuator short to groundShorted low
- C1040-12Lift actuator short to batteryShorted high
- C1040-13Lift actuator open circuitOpen circuit
- B1040-14Buzzer error offShorted low
- C1040-19Lift actuator overcurrentReal condition
- C1040-77Lift actuator reduced performanceOther
- C1041-00Lift spool position sensor inverted movementOther
- B1041-12Backup alarm error onOther
- B1041-14Backup alarm error offShorted low
- C1042-00Lift actuator uncommanded motionOther
- B1042-12Horn relay short to batteryShorted high
- B1042-14Horn relay short to ground or open circuitShorted low
- C1045-11Tilt actuator short to groundShorted low
- C1045-12Tilt actuator short to batteryShorted high
- C1045-13Tilt actuator open circuitOpen circuit
- C1045-19Tilt actuator overcurrentReal condition
- C1045-77Tilt actuator reduced performanceOther
- C1046-00Tilt spool position sensor inverted movementOther
- C1047-00Tilt actuator uncommanded motionOther
- B1050-12HVAC output short to batteryShorted high
- B1050-14HVAC output short to ground or open circuitShorted low
- U1051-00Cab controller interrupted power failurePart or controller
- C1051-11Two speed solenoid short to groundShorted low
- C1051-12Two speed solenoid short to batteryShorted high
- C1051-13Two speed solenoid open circuitOpen circuit
- C1051-19Two speed solenoid overcurrentReal condition
- B1051-93HVAC inside sensor in errorOther
- U1052-00Power failureOther
- B1052-93HVAC device sensor in errorOther
- B1053-93HVAC coil sensor in errorOther
- B1054-11HVAC clutch output error offShorted low
- B1054-12HVAC clutch output error onOther
- B1054-13HVAC clutch output open circuitOpen circuit
- B1054-19HVAC clutch output overcurrentReal condition
- U1055-00Aux controller interrupted power failurePart or controller
- B1055-93HVAC water valve in errorOther
- U1056-00Rear auxiliary controller interrupted power failurePart or controller
- B1060-F0Lift pedal not in neutralErratic or implausible
- P1060-16Air filter out of range lowOther
- P1060-17Air filter out of range highOther
- U1060-46Workgroup calibration failedPart or controller
- U1060-87Workgroup calibration requiredLost message
- B1060-93Lift pedal in errorOther
- U1061-00Workgroup calibration passedPart or controller
- B1061-16Lift pedal sensor a out of range lowShorted low
- B1061-17Lift pedal sensor a out of range highShorted high
- P1062-00Air filter pluggedLost message
- B1062-16Lift pedal position sensor b out of range lowShorted low
- B1062-17Lift pedal position sensor b out of range highShorted high
- B1063-00Lift pedal sensor in errorOther
- P1063-00Air filter pluggedLost message
- B1064-F0Lift joystick not in neutralErratic or implausible
- B1065-F0Lift input not in neutralErratic or implausible
- U1065-00Drive calibration passedPart or controller
- B1070-F0Tilt pedal not in neutralOther
- B1070-09Tilt pedal failureOther
- C1070-11Rear auxiliary base solenoid short to groundShorted low
- C1070-12Rear auxiliary base solenoid short to batteryShorted high
- C1070-13Rear auxiliary base solenoid open circuitOpen circuit
- B1070-93Tilt pedal in errorOther
- U1071-00Cab controller software updatedPart or controller
- C1071-11Rear auxiliary base lock solenoid short to groundShorted low
- C1071-12Rear auxiliary base lock solenoid short to batteryShorted high
- C1071-13Rear auxiliary base lock open circuitOpen circuit
- B1071-16Tilt pedal sensor a out of range lowOther
- B1071-17Tilt pedal sensor a out of range highOther
- B1072-16Tilt pedal position sensor b out of range highOther
- B1072-17Tilt pedal position sensor b out of range lowOther
- B1073-00Tilt pedal sensor in errorOther
- B1074-F0Tilt joystick not in neutralOther
- B1075-F0Tilt input not in neutralOther
- U1075-00Lights controller interrupted power failurePart or controller
- C1075-11Rear auxiliary rod solenoid short to groundShorted low
- C1075-12Rear auxiliary rod solenoid short to batteryShorted high
- C1075-13Rear auxiliary rod solenoid open circuitOpen circuit
- C1076-11Rear auxiliary rod lock solenoid short to groundShorted low
- C1076-12Rear auxiliary rod lock solenoid short to batteryShorted high
- C1076-13Rear auxiliary rod solenoid open circuitOpen circuit
- C1080-FAHydraulic charge pressure highLost message
- C1080-FBHydraulic charge pressure extremely highOther
- U1080-00Drive controller in calibration modePart or controller
- C1080-F8Hydraulic charge pressure extremely lowOther
- B1080-09Seat bar failureOther
- C1080-F9Low hydraulic pump pressureOther
- B1080-16Seat bar out of range lowOther
- B1080-17Seat bar out of range highOther
- U1084-00Workgroup in calibration modePart or controller
- B1090-00Door openOther
- B1091-16Door sensor out of range lowOther
- U1092-A2Cab controller system voltage lowShorted low
- U1092-A3Cab controller system voltage highShorted high
- U1092-08Cab controller no communicationLost message
- U1092-51Cab controller not programmedOther
- U1092-57Cab controller software version errorPart or controller
- C1093-00Hydraulic case drain filter switch pluggedLost message
- U1093-A2Battery voltage lowShorted low
- U1093-A3Battery voltage highShorted high
- U1093-08Mid controller no communicationLost message
- U1093-51Mid controller not calibratedLost message
- U1093-57Mid controller software version errorPart or controller
- B1095-13Window sensor open circuitOpen circuit
- B1095-16Window sensor out of range lowOther
- B1095-17Window sensor out of range highOther
- B1095-95Window sensor failureOther
- U1097-A2Aux controller system voltage lowShorted low
- U1097-A3Aux controller system voltage highShorted high
- U1097-08Aux controller bus signal / message failureOther
- C1097-16Hydraulic charge pressure sensor out of range lowOther
- C1097-17Hydraulic charge pressure sensor out of range highOther
- U1097-51Aux controller not programmedOther
- U1098-A2Rear auxiliary controller system voltage lowShorted low
- U1098-A3Rear auxiliary controller system voltage highShorted high
- U1098-08Rear auxiliary controller communication errorLost message
- U1098-51Rear auxiliary controller not programmedOther
- U1098-57Rear auxiliary controller software version errorPart or controller
- B1100-9EBob-Tach engage button stuck onOther
- B1101-9EBob-Tach disengage button stuck onOther
- W1105Lift rod solenoid short to batteryShorted high
- W1106Lift rod solenoid short to groundShorted low
- W1107Lift rod solenoid open circuitOpen circuit
- B1110-F0Left primary not in neutralErratic or implausible
- U1110-08Bob-Tach angle sensor no communicationLost message
- B1111-F0Left secondary not in neutralErratic or implausible
- U1111-08Bucket angle sensor no communicationLost message
- U1112-08Lift arm angle no communicationLost message
- U1113-08Frame angle sensor no communicationLost message
- B1120-F0Right primary not in neutralErratic or implausible
- M1121Seat bar sensor out of range highOther
- B1121-F0Right secondary not in neutralErratic or implausible
- M1122Seat bar sensor out of range lowOther
- B1122-F0Detent not in neutralErratic or implausible
- M1128Seat bar sensor failureErratic or implausible
- P1131-13Fuel filter inlet pressure sensor open circuitOpen circuit
- W1132Lift rod solenoid overcurrentOther
- P1134-12Fuel lift pump short to batteryShorted high
- P1134-13Fuel lift pump open circuitOpen circuit
- C1150-13Right drive motor direction open circuitOpen circuit
- C1150-16Right drive motor direction out of range lowShorted low
- C1150-17Right drive motor direction out of range highShorted high
- C1155-13Left drive motor direction open circuitOpen circuit
- C1155-16Left drive motor direction out of range lowOther
- C1155-17Left drive motor direction out of range highOther
- B1177-12Left turn signal short to batteryShorted high
- B1177-14Left turn signal short to ground or open circuitShorted low
- C1182-A3Alternator voltage highShorted high
- U1185-00Radio no communicationLost message
- B1187-12Right turn signal short to batteryShorted high
- B1187-14Right turn signal short to ground or open circuitShorted low
- C1190-00System voltage out of range lowOther
- C1195-00System voltage extremely lowOther
- W1205Tilt base solenoid short to batteryShorted high
- W1206Tilt base solenoid short to groundShorted low
- W1207Tilt base solenoid open circuitOpen circuit
- M1210Air inlet temperature highLost message
- M1211Air inlet temperature extremely highOther
- H1221Right primary out of range highShorted high
- H1222Right primary out of range lowShorted low
- H1224Right primary not in neutralOther
- W1232Tilt base solenoid overcurrentOther
- M1305Fuel hold solenoid short to batteryShorted high
- W1305Tilt rod solenoid short to batteryShorted high
- M1306Fuel hold solenoid short to groundShorted low
- W1306Tilt rod solenoid short to groundShorted low
- M1307Fuel hold solenoid open circuitOpen circuit
- W1307Tilt rod solenoid open circuitOpen circuit
- H1324Left primary not in neutralOther
- W1332Tilt rod solenoid overcurrentOther
- M1402Fuel pull output error onOther
- M1403Fuel pull output error offOther
- M1407Fuel pull output open circuitOpen circuit
- H1421Lift base pressure out of range highOther
- H1422Lift base pressure out of range lowOther
- M1428Fuel pull output failureOther
- H1502Ride control relay error onOther
- M1502Traction lock pull output error onOther
- H1503Ride control relay error offShorted low
- M1503Traction lock pull output error offOther
- W1505Pedal lock short to batteryShorted high
- W1506Pedal lock short to groundShorted low
- M1507Traction lock pull output open circuitOpen circuit
- W1507Pedal lock open circuitOpen circuit
- M1528Traction lock pull output failureOther
- H1602Ride control output error onOther
- H1603Ride control output error offShorted low
- M1605Traction lock hold solenoid short to batteryShorted high
- W1605Handle lock short to batteryShorted high
- M1606Traction lock hold solenoid short to groundShorted low
- W1606Handle lock short to groundShorted low
- H1607Ride control output open circuitOpen circuit
- M1607Traction lock hold solenoid open circuitOpen circuit
- W1607Handle lock open circuitOpen circuit
- H1628Ride control output failureOther
- M1632Hydraulic bypass overcurrentLost message
- M1705Hydraulic lock valve solenoid short to batteryShorted high
- M1706Hydraulic lock valve solenoid short to groundShorted low
- M1707Hydraulic lock valve solenoid open circuitOpen circuit
- M1732Hydraulic lock valve solenoid overcurrentOther
- M1802Power beyond valve output error onOther
- M1803Power beyond valve output error offShorted low
- M1805Spool lock 1 short to batteryShorted high
- M1806Spool lock 1 short to groundShorted low
- M1807Spool lock 1 open circuitOpen circuit
- M1832Spool lock 1 overcurrentReal condition
- M1902Power beyond valve relay error onOther
- M1903Power beyond valve relay error offShorted low
- M1910Engine ambient temperature highOther
- M1911Engine ambient temperature extremely highOther
- M1921Engine ambient temperature out of range highOther
- M1922Engine ambient temperature out of range lowOther
- M2005Two-speed primary solenoid short to batteryShorted high
- M2006Two-speed primary solenoid short to groundShorted low
- M2007Two-speed primary solenoid open circuitOpen circuit
- W2021Lift handle sensor out of range highShorted high
- W2022Lift handle sensor out of range lowShorted low
- M2032Two-speed primary overcurrentOther
- M2102Glow plug output error onOther
- M2103Glow plug output error offOther
- H2105Reverse fan solenoid short to batteryShorted high
- H2106Reverse fan solenoid short to groundShorted low
- H2107Reverse fan solenoid open circuitOpen circuit
- M2107Glow plug output open circuitOpen circuit
- W2121Lift pedal sensor out of range highShorted high
- W2122Lift pedal sensor out of range lowShorted low
- M2128Glow plug output failureOther
- H2132Reverse fan solenoid overcurrentReal condition
- M2202Starter output error onOther
- M2203Starter output error offOther
- M2207Starter output open circuitOpen circuit
- W2221Tilt handle sensor out of range highOther
- W2222Tilt handle sensor out of range lowOther
- M2228Starter output failureOther
- M2302Starter relay error onOther
- M2303Starter relay error offOther
- H2305Rear base solenoid short to batteryShorted high
- H2306Rear base solenoid short to groundShorted low
- H2307Rear base solenoid open circuitOpen circuit
- W2321Tilt pedal sensor out of range highOther
- W2322Tilt pedal sensor out of range lowOther
- H2332Rear base solenoid overcurrentReal condition
- M2402Fuel pull relay error onOther
- M2403Fuel pull relay error offOther
- H2405Rear rod solenoid short to batteryShorted high
- H2406Rear rod solenoid short to groundShorted low
- H2407Rear rod solenoid open circuitOpen circuit
- H2432Rear rod solenoid overcurrentOther
- M2502Traction pull relay error onOther
- M2503Traction pull relay error offOther
- H2505Diverter solenoid #2 short to batteryShorted high
- H2506Diverter solenoid #2 short to groundShorted low
- H2521Angle blade control switch out of range highShorted high
- M2521Load sense sensor out of range highOther
- H2522Angle blade control switch out of range lowShorted low
- M2522Load sense sensor out of range lowOther
- H2524Angle blade control switch out of neutralErratic or implausible
- M2602Glow plug relay error onOther
- M2603Glow plug relay error offOther
- H2605Front base solenoid short to batteryShorted high
- H2606Front base solenoid short to groundShorted low
- H2607Front base solenoid open circuitOpen circuit
- H2632Front base solenoid overcurrentOther
- H2705Front rod solenoid short to batteryShorted high
- H2706Front rod solenoid short to groundShorted low
- H2707Front rod solenoid open circuitOpen circuit
- M2721Throttle primary sensor out of range highOther
- M2722Throttle primary sensor out of range lowOther
- H2732Front rod solenoid overcurrentOther
- H2805Diverter solenoid short to batteryShorted high
- M2805Diverter output short to batteryShorted high
- H2806Diverter solenoid short to groundShorted low
- M2806Diverter output short to groundShorted low
- H2807Diverter output open circuitOpen circuit
- M2807Diverter output open circuitOpen circuit
- M2821Throttle secondary sensor out of range highOther
- M2822Throttle secondary sensor out of range lowOther
- W2824Lift input not in neutralOther
- H2832Diverter output overcurrentLost message
- H2848Diverter multiple inputLost message
- M2899Throttle secondary sensor calibration requiredPart or controller
- H2905High flow solenoid short to batteryShorted high
- H2906High flow solenoid short to groundShorted low
- H2907High flow solenoid open circuitOpen circuit
- M2910Exhaust gas temperature highOther
- W2924Tilt input not in neutralOther
- H2932High flow solenoid overcurrentOther
- H3028Controller memory failurePart or controller
- H3128Interrupted power failureOther
- M3128Interrupted power failureOther
- W3128Interrupted power failureOther
- M3204Workgroup controller no communicationLost message
- M3223Throttle controller not calibratedPart or controller
- W3223ACS calibration requiredLost message
- W3224ACS calibration performedPart or controller
- W3225ACS (ahc) calibration failedPart or controller
- M3228Throttle controller failurePart or controller
- W3231ACS/AHC tilt actuator faultOther
- W3232AHC tilt actuator wiring faultOther
- W3233AHC tilt handle wiring faultOther
- W3234ACS/AHC tilt actuator not in neutralReal condition
- W3235ACS/AHC tilt handle not in neutralErratic or implausible
- W3236ACS/AHC lift actuator faultOther
- W3237AHC lift actuator wiring faultOther
- W3238AHC lift handle wiring faultOther
- W3239ACS/AHC lift actuator not in neutralReal condition
- W3240ACS/AHC lift handle not in neutralOther
- W3241AHC no communicationLost message
- W3249ACS lift actuator short to groundShorted low
- W3250ACS tilt actuator short to groundShorted low
- W3251ACS lift actuator short to batteryShorted high
- W3252ACS tilt actuator short to batteryShorted high
- W3253ACS lift handle/pedal short to groundShorted low
- W3254ACS tilt handle/pedal short to groundShorted low
- W3255ACS lift handle/pedal short to batteryShorted high
- W3256ACS tilt handle/pedal short to batteryShorted high
- W3257ACS lift actuator reduced performanceOther
- W3258ACS tilt actuator reduced performanceOther
- W3259ACS lift actuator wrong directionOther
- W3260ACS tilt actuator wrong directionOther
- W3261ACS handle lock short to groundShorted low
- W3262ACS handle lock short to batteryShorted high
- W3263ACS pedal lock short to groundShorted low
- W3264ACS pedal lock short to batteryShorted high
- W3265ACS sensor supply voltage out of rangeOther
- W3266ACS battery voltage out of rangeOther
- W3267ACS switch flipped while operatingOther
- W3268ACS lift handle information errorOther
- W3270ACS right hand drive short to groundShorted low
- W3271ACS right hand drive short to batteryShorted high
- W3274ACS left joystick X-axis out of rangeOther
- W3275ACS interrupted unswitched powerPart or controller
- W3276ACS CAN joystick information errorLost message
- W3277ACS remote control information errorOther
- W3295Workgroup calibration passedPart or controller
- W3296Workgroup calibration failedPart or controller
- W3297ACS (ahc) controller programmedOther
- W3298Workgroup in calibration modePart or controller
- M3299Throttle controller calibration in processPart or controller
- W3299Workgroup calibration requiredPart or controller
- M3304Deluxe panel (mseries) no communicationLost message
- W3304Main controller no communicationLost message
- R3327IQ touch CAN errorLost message
- R3334IQ touch CAN RX errorLost message
- R3335IQ touch CAN TX errorLost message
- M3372Display software incompatiblePart or controller
- M3373Display software outdatedPart or controller
- M3404Deluxe panel no communicationLost message
- M3505Hydraulic fan short to batteryShorted high
- M3506Hydraulic fan short to groundShorted low
- M3507Hydraulic fan open circuitOpen circuit
- M3532Hydraulic fan overcurrentReal condition
- A3623ACD not programmedOther
- H3648ACD multipleOther
- H3702Power Bob-Tach up solenoid error onShorted high
- M3702Hyd exchange output error onOther
- M3703Hyd exchange output error offShorted low
- M3705Two speed secondary short to batteryShorted high
- M3706Two speed secondary short to groundShorted low
- M3707Two speed secondary open circuitOpen circuit
- M3732Two speed secondary overcurrentReal condition
- M3805Auxiliary hydraulic lock short to batteryShorted high
- M3806Auxiliary hydraulic lock short to groundShorted low
- M3807Auxiliary hydraulic lock open circuitOpen circuit
- M3832Auxiliary hydraulic lock overcurrentReal condition
- H3904Left joystick in errorOther
- M3904Jog shuttle no communicationLost message
- R3904Jog shuttle no communicationLost message
- W3904Left joystick no communicationLost message
- D3905Left joystick X-axis not in neutralErratic or implausible
- W3905Left joystick X-axis not in neutralOther
- D3907Left joystick Y-axis not in neutralErratic or implausible
- H3912Left joystick thumb switch not in neutralErratic or implausible
- H3913Left joystick grip no communicationLost message
- H3916Left joystick not connectedOpen circuit
- H3928Left joystick failureOther
- H3948Left joystick multipleOther
- W4004Right joystick no communicationLost message
- W4005Right joystick X-axis not in neutralErratic or implausible
- D4007Right joystick Y-axis not in neutralErratic or implausible
- W4007Right joystick Y-axis not in neutralOther
- H4013Right joystick grip no communicationLost message
- H4016Right joystick not connectedOpen circuit
- H4028Right joystick failureOther
- M4028Wrong ECU detectedOther
- H4048Right joystick multipleOther
- M4109Alternator lowShorted low
- M4110Alternator highShorted high
- M4204Keyless entry no communicationLost message
- M4228Wrong DCU detectedOther
- M4304Keyless start panel no communicationLost message
- R4304Keyless start panel no communicationLost message
- M4404Auxiliary no communicationLost message
- H4423Auxiliary not programmedOther
- M4472Secondary controller software incompatiblePart or controller
- M4473Secondary controller software outdatedPart or controller
- H4497Secondary controller programmedOther
- M4510Water in fuel too highLost message
- M4511Water in fuel extremely highOther
- M4521Water in fuel sensor out of range highOther
- M4522Water in fuel sensor out of range lowOther
- M4530Water in fuel sensor faultOther
- A46215v sensor supply out of range highShorted high
- H46215 volt sensor supply out of range highOther
- M46215v sensor supply out of range highOther
- A46225v sensor supply out of range lowShorted low
- H46225 volt sensor supply out of range lowOther
- M46225v sensor supply out of range lowOther
- A47218v sensor supply out of range highOther
- H4721Sensor supply 1 out of range highOther
- M47218v sensor supply out of range highOther
- W4721Sensor supply out of range highOther
- A47228v sensor supply out of range lowOther
- H4722Sensor supply 1 out of range lowOther
- M47228v sensor supply out of range lowOther
- W4722Sensor supply out of range lowOther
- M4802Front light relay error onOther
- M4803Front light relay error offShorted low
- H48215v sensor supply out of range highOther
- H48225v sensor supply out of range lowOther
- M4902Rear light relay error onLost message
- M4903Rear light relay error offShorted low
- VS5001-03Thumb wheel (rh), voltage above normalShorted high
- VS5001-04Thumb wheel (rh), voltage below normalShorted low
- M5002Front light output error onOther
- VS5002-03Thumb wheel (lh), voltage above normalShorted high
- VS5002-04Thumb wheel (lh), voltage below normalShorted low
- M5003Front light output error offShorted low
- VS5003-03Accel pedal sensor, voltage above normalShorted high
- VS5003-04Accel pedal sensor, voltage below normalShorted low
- W5004Lift float failed to maintain floatOther
- VS5004-03Parking brake press. sensor, voltage above normalShorted high
- VS5004-04Parking brake press. sensor, voltage below normalShorted low
- VS5005-03Dial, voltage above normalShorted high
- VS5005-04Dial, voltage below normalShorted low
- M5007Front light output open circuitOpen circuit
- M5028Front light output failureOther
- M5102Rear light output error onOther
- M5103Rear light output error offShorted low
- M5107Rear light output open circuitOpen circuit
- M5128Rear light output failureOther
- M5202Press to operate switch error onShorted high
- M5205Offset base solenoid short to batteryShorted high
- M5206Offset base solenoid short to groundShorted low
- M5207Offset base solenoid open circuitOpen circuit
- M5221Press to operate switch out of range highOther
- M5222Press to operate switch out of range lowOther
- M5232Offset base solenoid overcurrentOther
- M5305Press to operate light short to batteryShorted high
- M5306Press to operate light short to groundShorted low
- M5307Offset rod solenoid open circuitOpen circuit
- M5332Offset rod solenoid overcurrentOther
- M5405Spool lock 2 short to batteryShorted high
- M5406Spool lock 2 short to groundShorted low
- M5407Spool lock 2 open circuitOpen circuit
- M5421Offset control switch out of range highOther
- M5422Offset control switch out of range lowOther
- M5424Offset control switch out of neutralOther
- M5432Spool lock 2 overcurrentOther
- M5505Auxiliary base solenoid short to batteryShorted high
- M5506Auxiliary base solenoid short to groundShorted low
- M5507Auxiliary base solenoid open circuitOpen circuit
- M5532Auxiliary base solenoid overcurrentReal condition
- M5605Auxiliary rod solenoid short to batteryShorted high
- M5606Auxiliary rod solenoid short to groundShorted low
- M5607Auxiliary rod solenoid open circuitOpen circuit
- M5632Auxiliary rod solenoid overcurrentOther
- H5705Angle blade aux 4 base short to batteryShorted high
- H5706Angle blade aux 4 base short to groundShorted low
- H5707Angle blade aux 4 base open circuitOpen circuit
- M5721Auxiliary control switch out of range highOther
- M5722Auxiliary control switch out of range lowOther
- M5724Auxiliary control switch out of neutralOther
- H5732Angle blade aux 4 base overcurrentOther
- H5805Angle blade aux 4 rod short to batteryShorted high
- H5806Angle blade aux 4 rod short to groundShorted low
- H5807Angle blade aux 4 rod open circuitOpen circuit
- M5810Fuel temperature highLost message
- M5811Fuel temperature extremely highOther
- M5815Fuel temperature shutdownOther
- M5826Fuel temperature pre shutdownOther
- H5832Angle blade aux 4 rod overcurrentOther
- M5902DPF regeneration switch error onOther
- M6002DPF inhibit regen switch error onOther
- M6021Left control switch out of range highOther
- M6022Left control switch out of range lowOther
- M6024Left control switch out of neutralOther
- M6102Remote parked regeneration switch error onOther
- M6121Right control switch out of range highOther
- M6122Right control switch out of range lowOther
- M6124Right control switch out of neutralOther
- M6202Tailgate fan 1 error onOther
- M6203Tailgate fan 1 error offShorted low
- M6204Load moment sensor in errorOther
- M6221Overload warning sensor out of range highReal condition
- M6222Overload warning sensor out of range lowReal condition
- M6228Tailgate fan 1 failureOther
- M6302Tailgate fan 2 error onOther
- M6303Tailgate fan 2 error offOther
- M6328Tailgate fan 2 failureOther
- M6402Switched power relay error onOther
- M6403Switched power relay error offShorted low
- M6505ECU power short to batteryShorted high
- M6506ECU power short to groundShorted low
- M6507ECU power open circuitOpen circuit
- M6604ECU no communicationLost message
- M6702HVAC output error onOther
- M6703HVAC output error offShorted low
- M6707HVAC output open circuitOpen circuit
- M6728HVAC output failureOther
- M6802HVAC relay error onOther
- M6803HVAC relay error offShorted low
- M6904DCU no communicationLost message
- M6905Dump valve short to batteryShorted high
- M6906Dump valve short to groundShorted low
- M6907Dump valve open circuitOpen circuit
- M6932Dump valve overcurrentReal condition
- M7002Switched power output error onOther
- M7003Switched power output error offShorted low
- M7007Switched power output open circuitOpen circuit
- M7028Switched power output failureOther
- M7102Electric fan output error onOther
- M7103Electric fan output error offShorted low
- M7107Electric fan output open circuitOpen circuit
- M7202Electric fan relay error onOther
- M7203Electric fan relay error offShorted low
- M7304Remote control no communicationLost message
- W7304Remote control no communicationLost message
- M7316Remote control not connectedOpen circuit
- H7404Main controller no communicationLost message
- L7404Main controller no communicationLost message
- R7404Main controller no communicationLost message
- M7423Main controller not programmedOther
- R7423Display not programmedOther
- M7472Main controller software incompatiblePart or controller
- M7473Main controller software outdatedPart or controller
- R7492Main controller authentication failedPart or controller
- M7497Main controller software updatedPart or controller
- D7501Drive/drive+ CAN joystick information errorLost message
- D7502Drive controller needs programmingOther
- D7504Drive no communication from drive controllerLost message
- M7504Drive no communicationLost message
- W7504Drive controller no communicationLost message
- D7505Drive left joystick X-axis not in neutralOther
- D7506Drive+ steering valve cartridge stuckOther
- D7507Drive left joystick Y-axis not in neutralOther
- D7508Drive right joystick Y-axis not in neutralOther
- D7509Drive ISO/H pattern switch short to ground or batteryShorted low
- D7510Drive improper joysticks installedOther
- D7511Drive left speed sensor not connectedOpen circuit
- D7512Drive right speed sensor not connectedOpen circuit
- D7513Drive+ right front wheel angle sensor stuckOther
- D7514Drive+ left front wheel angle sensor stuckOther
- D7515Drive+ right rear wheel angle sensor stuckOther
- D7516Drive+ left rear wheel angle sensor stuckOther
- D7517Drive left swash plate not in neutralOther
- D7518Drive right swash plate not in neutralOther
- D7519Drive left joystick X-axis out of range highShorted high
- D7521Drive left joystick Y-axis out of range highShorted high
- D7522Drive right joystick Y-axis out of range highShorted high
- D7523Drive+ right front wheel angle sensor out of range highShorted high
- D7524Drive+ left front wheel angle sensor out of rane highOther
- D7525Drive+ right rear wheel angle sensor out of range highOther
- D7526Drive+ left rear wheel angle sensor out of range highOther
- D7527Drive left swash plate out of positionOther
- D7528Drive right swash plate out of positionOther
- D7529Drive left joystick X-axis out of range lowShorted low
- D7531Drive left joystick Y-axis out of range lowShorted low
- D7532Drive right joystick Y-axis out of range lowShorted low
- D7533Drive+ right front wheel angle sensor out of range lowShorted low
- D7534Drive+ left front wheel angle sensor out of range lowOther
- D7535Drive+ right rear wheel angle sensor out of range lowOther
- D7536Drive+ left rear wheel angle sensor out of range lowOther
- D7537Drive 5 volt sensor supply 1 out of range lowOther
- D7538Drive+ sensor supply 2 out of range lowOther
- D7539Drive left swash plate sensor out of range highOther
- D7540Drive left swash plate sensor out of range lowOther
- D7541Drive right swash plate sensor out of range highOther
- D7542Drive right swash plate sensor out of range lowOther
- D7543Drive left forward drive solenoid error onOther
- D7544Drive left reverse drive solenoid error onOther
- D7545Drive right forward drive solenoid error onOther
- D7546Drive right reverse drive solenoid error onOther
- D7547Drive+ right front steer extend short to batteryShorted high
- D7548Drive+ left front steer extend short to batteryShorted high
- D7549Drive+ right rear steer extend short to batteryShorted high
- D7550Drive+ left rear steer extend short to batteryShorted high
- D7551Drive+ steer pressure short to batteryShorted high
- D7552Drive backup alarm error onOther
- D7553Drive left forward drive solenoid error offOther
- D7554Drive left reverse drive solenoid error offOther
- D7555Drive right forward drive solenoid error offOther
- D7556Drive right reverse drive solenoid error offOther
- D7557Drive+ right front steer extend short to groundShorted low
- D7558Drive+ right front steer retract short to groundShorted low
- D7559Drive+ left front steer extend short to groundShorted low
- D7560Drive+ left front steer retract short to groundShorted low
- D7561Drive+ right rear steer extend short to groundShorted low
- D7562Drive+ right rear steer retract short to groundShorted low
- D7563Drive+ left rear steer extend short to groundShorted low
- D7564Drive+ left rear steer retract short to groundShorted low
- D7565Drive+ steer pressure short to groundShorted low
- D7566Drive backup alarm error offOther
- D7567Drive no communication from bobcat controllerLost message
- D7568Drive+ angle sensors not calibratedLost message
- D7569Drive battery voltage out of range highOther
- D7570Drive interrupted power (also occurs after software updates)Part or controller
- D7571Drive battery voltage out of range lowOther
- D7572Drive drive pump not calibratedLost message
- D7573Drive ISO/H pattern switch flipped while operatingOther
- D7574Drive right wheel speed uncommanded motionOther
- D7575Drive left wheel speed uncommanded motionOther
- D7576Drive no communication from ACS controllerLost message
- D7577Drive left speed sensor out of range highOther
- D7578Drive right speed sensor out of range highOther
- D7579Drive left speed sensor out of range lowOther
- D7580Drive right speed sensor out of range lowOther
- D7581Drive+ right front steer retract short to batteryShorted high
- D7582Drive+ left front steer retract short to batteryShorted high
- D7583Drive+ right rear steer retract short to batteryShorted high
- D7584Drive+ left rear steer retract short to batteryShorted high
- D7585Drive 5 volt sensor supply 1 out of range highOther
- D7586Drive+ sensor supply 2 out of range highOther
- D7587Drive software update requiredPart or controller
- D7588Drive/drive+ switched power stuck onOther
- D7589Drive switched power error offShorted low
- D7590Drive drive calibration performedPart or controller
- D7591Drive left swashplate sensor reversedOther
- D7592Drive right swashplate sensor reversedOther
- D7593Drive unresponsive right speed sensorOther
- D7594Drive unresponsive left speed sensorOther
- D7595Drive left speed sensor reverse directionOther
- D7596Drive right speed sensor reverse directionOther
- D7597Drive controller programmedOther
- D7598Drive controller in calibration modePart or controller
- D7599Drive controller in angle calibration modePart or controller
- H7604Left hand panel no communicationLost message
- M7604Left display panel no communicationLost message
- L7672Standard panel programming errorOther
- A7701Key switch activeOther
- M7748Key switch multipleOther
- A7901E-stop activeOther
- H7902Door unlock error onShorted high
- M7902Forestry door closedOther
- H7903Door unlock error offShorted low
- M7974Door openOther
- A8002Output a error onOther
- H8002ACD output a error onOther
- A8003Output a error offShorted low
- H8003ACD output a error offOther
- M8004Cooling fan controller no communicationLost message
- A8005Output a short to batteryShorted high
- M8005Cooling fan short to batteryShorted high
- A8006Output a short to groundShorted low
- M8006Cooling fan short to groundShorted low
- A8007Output a open circuitOpen circuit
- M8021Cooling fan out of range highShorted high
- M8022Cooling fan out of range lowShorted low
- M8025Cooling fan unresponsiveOpen circuit
- M8027Cooling fan CAN errorLost message
- M8028Cooling fan failureLost message
- M8029Cooling fan wiring faultLost message
- M8030Cooling fan controller faultPart or controller
- A8032Output a overcurrentReal condition
- A8102Output b error onOther
- H8102ACD output b error onOther
- A8103Output b error offOther
- H8103ACD output b error offOther
- A8105Output b short to batteryShorted high
- A8106Output b short to groundShorted low
- A8107Output b open circuitOpen circuit
- A8132Output b overcurrentOther
- A8202Output c error onOther
- H8202ACD output c error onOther
- A8203Output c error offOther
- H8203ACD output c error offOther
- A8205Output c short to batteryShorted high
- A8206Output c short to groundShorted low
- A8207Output c open circuitOpen circuit
- M8228AdBlue/DEF sensor mismatchOther
- A8232Output c overcurrentOther
- A8302Output d error onOther
- H8302ACD output d error onOther
- M8302Wait to start lamp error onShorted high
- A8303Output d error offOther
- H8303ACD output d error offOther
- M8303Wait to start lamp error offShorted low
- A8305Output d short to batteryShorted high
- A8306Output d short to groundShorted low
- A8307Output d open circuitOpen circuit
- A8332Output d overcurrentOther
- A8402Output e error onOther
- H8402ACD output e error onOther
- M8402DeSOx service requestedOther
- A8403Output e error offOther
- H8403ACD output e error offOther
- A8405Output e short to batteryShorted high
- A8406Output e short to groundShorted low
- A8407Output e open circuitOpen circuit
- A8432Output e overcurrentOther
- M8450DeSOx required but inhibitedOther
- A8502Output f error onOther
- H8502ACD output f error onOther
- A8503Output f error offOther
- H8503ACD output f error offOther
- A8505Output f short to batteryShorted high
- A8506Output f short to groundShorted low
- A8507Output f open circuitOpen circuit
- A8532Output f overcurrentOther
- M8541DPF automatic regeneration activeOther
- M8542DPF automatic regeneration activeOther
- M8543DPF regeneration requiredOther
- M8551DPF regeneration needed inhibit activeOther
- M8552DPF regeneration needed - inhibit activeOther
- M8553DPF remote parked regeneration required - remote regeneration kit requiredLost message
- M8554DPF service regeneration required - contact bobcat dealerReal condition
- M8555DPF service requiredOther
- M8560DPF service regeneration activeReal condition
- M8561DPF service regeneration activeOther
- M8562DPF service regeneration activeOther
- M8563DPF service regeneration activeOther
- M8564DPF service regeneration activeOther
- A8602Output g error onOther
- H8602ACD output g error onOther
- A8603Output g error offOther
- H8603ACD output g error offOther
- A8605Output g short to batteryShorted high
- A8606Output g short to groundShorted low
- A8607Output g open circuitOpen circuit
- M8615Engine speed derate shutdownOther
- M8625Engine speed derate unresponsiveOther
- A8702Output h error onOther
- H8702ACD output h error onOther
- A8703Output h error offOther
- H8703ACD output h error offOther
- A8705Output h short to batteryShorted high
- A8706Output h short to groundShorted low
- A8707Output h open circuitOpen circuit
- M8715Torque derate shutdownOther
- M8725Torque derate unresponsiveOther
- A8802Reverse solenoid error onOther
- A8803Reverse solenoid error offShorted low
- M8804Telematics not connectedOpen circuit
- H9110Fuel pressure at filter inlet too highLost message
- H9111Fuel pressure at filter inlet extremely highOther
- M9111Fuel filter extremely pluggedLost message
- M9117Fuel filter pluggedLost message
- H9121Fuel pressure out of range highOther
- H9122Fuel pressure out of range lowOther
- H9144Fuel filter derate level 1Real condition
- M9144Fuel filter derate level 1Real condition
- H9145Fuel filter derate level 2Real condition
- M9145Fuel filter derate level 2Real condition
- H9202Fuel lift pump output error onShorted high
- M9202Fuel lift pump error onShorted high
- H9203Fuel lift pump output error offShorted low
- M9203Fuel lift pump error offShorted low
- H9287Fuel lift pump protection time-outLost message
- M9287Fuel pump failure time exceededReal condition
- H9309Fuel pressure lowLost message
- M9309Fuel pressure lowLost message
- H9314Fuel pressure extremely lowOther
- M9314Fuel pressure extremely lowOther
- H9321Fuel pressure out of range highOther
- M9321Fuel pressure out of range highOther
- H9322Fuel pressure out of range lowOther
- M9322Fuel pressure out of range lowOther
- H9344Fuel pressure derate level 1Real condition
- M9344Fuel pressure derate level 1Real condition
- R9604Radio no communicationLost message
- M9701Turbo prime sequence activeOther
Covers Skid steers, Track loaders, Mini excavators.
Where to look
- 01On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
- 02On standard-display R-series, use the jog shuttle to select Service Codes.
- 03On M2 machines with the deluxe panel, turn the jog shuttle to Service Codes.
- 04Note the code and the machine serial number, then look it up in the operation manual…
- 05After the repair, restart the machine and watch the panel to confirm the code does…
How to read Bobcat fault codes, in full
- On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
- On standard-display R-series, use the jog shuttle to select Service Codes.
- On M2 machines with the deluxe panel, turn the jog shuttle to Service Codes; with the standard instrument panel press the information button to reach the open-book-and-wrench screen and cycle through the active codes.
- Note the code and the machine serial number, then look it up in the operation manual or the Bobcat fault code search at bobcat.com.
- After the repair, restart the machine and watch the panel to confirm the code does not return.
How urgent is a Bobcat code?
- Stop now51 codes
- Shut down and fix before working on. Running on risks damage or the machine locks out.
- Check soon1,177 codes
- The machine may derate or limit a function. Find the cause before the next shift.
- Information30 codes
- A reminder or status message. Nothing is failing yet.
Pick your system
Find the part of the machine, then the family your code belongs to.
- Code range
- The first and last code in the family, as the machine shows them.
- Codes
- How many codes the family holds; each is explained on its page.
- Severity mix
- The share of stop, check and info codes. The dot after it is the most urgent one in the family.
Filters25 codes
Fuel system57 codes
Engine105 codes
Engine starting33 codes
Engine controls14 codes
Electrical156 codes
- System, battery, alternator and controller voltageLOWVLTG – D757135 codes
- ECU power, switched power and key switchB10D0-12 – M774819 codes
- Sensor supply voltages (5 V, 8 V and other)32-65 – D758626 codes
- Front work, road lights and turn signalsB116F-11 – M502822 codes
- Rear light relays, outputs and lights controllerU109C-08 – M512810 codes
- Horn, buzzer, backup alarm, wipers and washerVRY002-05 – D756615 codes
- HVAC climate control outputs and sensorsB1050-12 – M680316 codes
- Rear work, marker, tail, stop and plate lampsB1034-12 – B1039-1313 codes
Operator presence163 codes
- Lift and tilt handle, pedal and joystick inputs32-33 – W326847 codes
- Left joystick and drive joystick inputsU10B0-08 – H760435 codes
- Right joystick and drive pattern switchB10BC-F0 – D757332 codes
- Seat bar, press to operate, cab door and door lockC10B0-00 – M797424 codes
- Control switches, remote control and jog shuttleU10D0-08 – M731625 codes
Hydraulics281 codes
- Lift and tilt spool position sensors and lift floatC104A-00 – W500425 codes
- Hydraulic oil and case drain temperaturesVSE001-00 – M072225 codes
- Hydraulic charge pressure, workgroup and load sensing pressure05-09 – M622227 codes
- Lift and tilt actuators32-31 – W326040 codes
- Lift and tilt spool solenoids, ride control and valves19-02 – M693238 codes
- Bob-Tach controls and boom, arm and bucket angle sensorsVSE007-03 – H370223 codes
- E145/E165 pump, flow control and travel valvesVPV001-05 – VSV012-0638 codes
- E145/E165 pressure sensorsVSP001-02 – VSP018-0439 codes
- E145/E165 inputs, relays and attachment valvesVSV001-05 – VS5005-0426 codes
Safety interlocks54 codes
Controller99 codes
Auxiliary hydraulics157 codes
Drive114 codes
Most searched Bobcat codes
- 01-17Air filter plugged
- 03-09Battery voltage low
- 04-09Engine oil pressure low
- 04-15Engine oil pressure shutdown level
- 05-09Hydraulic charge pressure low
- 05-15Hydraulic charge pressure shutdown level
- 06-13Engine speed no signal
- 07-10Hydraulic oil temperature high
- 08-10Engine coolant temperature high
- 08-15Engine coolant temperature shutdown level
- 11-05Seat bar sensor short to battery
- 11-06Seat bar sensor short to ground
- 14-03Fuel shut-off pull solenoid error OFF
- 15-03Traction lock pull solenoid error OFF
- 16-06Traction lock hold solenoid short to ground
- 17-06Hydraulic lock valve solenoid short to ground
- 17-07Hydraulic lock valve solenoid open circuit
- 22-03Starter error OFF
- M0117Air filter plugged
- M0217Hydraulic/hydrostatic filter plugged
- M0309System voltage too low
- M0322System voltage out of range low
- M0409Engine oil pressure too low
- M0415Engine oil pressure shutdown
- M0509Hydraulic charge pressure low
- M0515Hydraulic charge pressure shutdown
- M0613Engine speed no signal
- M0710Hydraulic oil temperature too high
- M0810Engine coolant temperature too high
- M0815Engine coolant temperature shutdown
- M0909Fuel level too low
- M1121Seat bar sensor out of range high
- M1122Seat bar sensor out of range low
- M1403Fuel pull output error off
- M1606Traction lock hold solenoid short to ground
- M1706Hydraulic lock valve solenoid short to ground
- M2006Two-speed primary solenoid short to ground
- M2203Starter output error off
- M2899Throttle secondary sensor calibration required
Quick answers
How do I read Bobcat fault codes?
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu. On standard-display R-series, use the jog shuttle to select Service Codes.
Which Bobcat codes mean stop now?
51 of the 1,258 Bobcat codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example 04-15, 05-15, 08-15, 14-03. 1,177 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.
What should I check first on a Bobcat code?
Most Bobcat codes here (238 of 1258) read as shorted low: the signal sits at or near zero volts - less than a working sensor can send. First test, as general workshop practice: key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Sources
Every code was read from these documents and written in our own words.
Other makers
Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.
Post a request