Bobcat · Fuel system
Bobcat Fuel level, pressure, temperature and water sensors fault codes
These are the sensors that watch the fuel before it reaches the injectors: tank level, fuel pressure at the filter and rail side, fuel temperature and the water-in-fuel probe in the filter. A code names the sensor and how it failed, whether out of range, open or reporting a real low or high condition.
Where this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
What do these codes mean?
Bobcat codes VSE002-03 to M9344 are all about the fuel level, pressure, temperature and water sensors. The most common failure type is lost message (5 of 35); 6 need an immediate stop. Start with this check: treat a pressure, water or level code as real until proven otherwise: check the fuel level, drain the water separator and confirm the filter is not blocked.
How urgent are they?
6 of 35 codes here mean stop now; 27 can wait until the shift ends, but find the cause before the next one; 2 are information only.
- Stop now6
- Check soon27
- Info2
What should I check first?
Treat a pressure, water or level code as real until proven otherwise: check the fuel level, drain the water separator and confirm the filter is not blocked.
Shared checks35 of 35
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Bobcat VSE002-03Fuel sensor, voltage above normal
The signal voltage from the fuel sensor is above the normal range. That usually means a signal wire shorted to supply, an open ground or a failed sensor.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to a supply wire
- Open sensor ground
- Sensor failed
Checks
- 1Check the sensor ground at the fuel sensor plug and its continuity back to the controller
- 2Test the signal wire for voltage with the plug off
- 3Swap in a known good sensor to see if the reading moves back into range
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat VSE002-04Fuel sensor, voltage below normal
The signal voltage from the fuel sensor is below the normal range. That usually means a short to ground, a missing sensor supply or a failed sensor.· Shorted lowShorted lowCheck soonCauses
- Sensor wire shorted to ground
- Open sensor supply or ground
- Sensor failed
Checks
- 1Check the 5 V supply and ground at the fuel sensor plug with the key on
- 2Test the signal wire to ground with the plug off
- 3Compare the reading with a known good sensor or the same input on a matching machine
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat VSE004-01WIF sensor, signal below normal range
The wif sensor signal is below its normal range. The controller treats the reading as unreliable until it is back inside the window.· Real conditionReal conditionCheck soonCauses
- Sensor reading a real low value
- Sensor drift or failure
- Signal wire shorted to ground or open
Checks
- 1Compare the wif sensor reading with a separate gauge or probe
- 2Check the sensor wiring for shorts to ground and open circuits
- 3Replace the sensor if the real value is normal but the reading stays low
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat VSE004-03WIF sensor, voltage above normal
The signal voltage from the wif sensor is above the normal range. That usually means a signal wire shorted to supply, an open ground or a failed sensor.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to a supply wire
- Open sensor ground
- Sensor failed
Checks
- 1Check the sensor ground at the wif sensor plug and its continuity back to the controller
- 2Test the signal wire for voltage with the plug off
- 3Swap in a known good sensor to see if the reading moves back into range
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat VSE004-04WIF sensor, voltage below normal
The signal voltage from the wif sensor is below the normal range. That usually means a short to ground, a missing sensor supply or a failed sensor.· Shorted lowShorted lowCheck soonCauses
- Sensor wire shorted to ground
- Open sensor supply or ground
- Sensor failed
Checks
- 1Check the 5 V supply and ground at the wif sensor plug with the key on
- 2Test the signal wire to ground with the plug off
- 3Compare the reading with a known good sensor or the same input on a matching machine
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat 09-09Fuel level low
Fuel level is low. It is a low-fuel warning, not an engine fault. The machine will run normally until the tank actually runs dry.· OtherOtherInfoCauses
- Sender wire or ground fault
- Gauge calibration error
- Fuel sender float stuck low
Checks
- 1Look at the tank with the dipstick or the filler neck and refuel if it is truly low
- 2Check the sender plug on top of the tank for corrosion and push the connector firmly together
- 3Remove the sender and check its resistance across the range as the float is moved
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 09-21Fuel level out of range high
The fuel level signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to supply
- Open sensor ground giving a floating high signal
- Sensor failed high
Checks
- 1Check the ground wire of the fuel level for continuity
- 2Look at the live reading on the display and see if it sits at the top of its scale
- 3Test the signal wire for stray voltage with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 09-22Fuel level out of range low
The fuel level signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Open signal wire or missing supply
- Sensor failed low
Checks
- 1Check the supply voltage at the fuel level plug with the key on
- 2Look at the live reading on the display and see if it sits at the bottom of its scale
- 3Test the signal wire to ground with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0909Fuel level too low
The fuel gauge sender says the tank is nearly empty. It is a low-fuel warning, not an engine fault.· Real conditionReal conditionInfoCauses
- Fuel pickup or tank slosh baffle issue
- Fuel sender float stuck low
- Sender wire or ground fault
- Gauge calibration error
Checks
- 1If the tank is full, check the sender float for freedom of movement in the tank
- 2Check the sender ground connection against bare metal on the frame
- 3Compare the gauge with the actual fuel by measuring how much fuel it takes to fill
- 4After refuelling, clear the code and see whether it returns while the gauge shows a full tank
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M0921Fuel level out of range high
The fuel level sender signal is above its valid range, so the gauge reading cannot be trusted.· OtherOtherCheck soonCauses
- Pushed-back pin or wet connector at the sensor
- Short to supply or to the fuel sender supply from the controller on the signal wire at the fuel level sender plug
- Internal failure of the fuel level sender that pegs it high
Checks
- 1Check the signal at the fuel level sender plug with the key on; it should sit within the normal 0.5-4.5 V span and never at full supply
- 2Look at the harness running along the fuel tank and its filler neck for chafing against a supply wire and for heat damage
- 3Disconnect the plug and probe the controller-side fuel sender supply from the controller; it should read about 5 V where there is one, and the signal pin should not follow battery voltage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0922Fuel level out of range low
The fuel level sender signal is below its valid range, so the gauge cannot be trusted. That usually means a wiring or sensor fault, not a real reading. The fuel gauge is unreliable until the circuit is fixed.· OtherOtherCheck soonCauses
- Loose or unplugged fuel level sender connector
- Signal wire grounded where the harness runs through the harness running along the fuel tank and its filler neck
- Lost fuel sender supply from the controller at the fuel level sender, or a broken signal wire
Checks
- 1Look for green corrosion, pushed-back pins or a missing seal inside the fuel level sender plug
- 2Measure the fuel sender supply from the controller at the unplugged fuel level sender connector with the key on; no voltage there means an open supply wire or a controller fault
- 3With the plug removed, a good fuel level sender signal wire should not read zero ohms to ground; a short means chafed insulation somewhere along the harness running along the fuel tank and its filler neck
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat P1131-13Fuel filter inlet pressure sensor open circuit
The controller sees an open circuit on the fuel filter inlet pressure sensor, meaning no current can flow through it. The function it drives does not work until the break is repaired.· Open circuitOpen circuitCheck soonCauses
- Pin backed out of the connector or plug not latched
- Wire broken inside its insulation near a bend or clamp
- Coil or element burnt open
Checks
- 1Check the connector at the fuel filter inlet pressure sensor is fully seated and its lock tab engaged
- 2Measure the resistance across the part with the plug off; infinite resistance confirms an open
- 3Check continuity of each wire from the plug back to the controller connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Bobcat M4510Water in fuel too high
The water in fuel reads above its warning level. The controller flags it so the operator can act before the machine reaches its shutdown limit.· Lost messageLost messageCheck soonCauses
- Real overload or overheat on the system
- Restricted flow or poor cooling
- Sensor reading high
Checks
- 1Verify the real value with a separate gauge or probe before replacing anything
- 2Check cooling, filters and flow in the system the water in fuel belongs to
- 3Check the sensor wiring if the real value turns out normal
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat M4511Water in fuel extremely high
The water in fuel is far above its normal level. The controller may reduce power or shut the machine down to protect it.· OtherOtherStop nowCauses
- Serious overheat or overpressure
- Blocked cooler or relief valve
- Sensor reading extremely high
Checks
- 1Stop the machine and let it cool before testing
- 2Verify the real value with a separate gauge or probe
- 3Check cooler, relief valve and airflow for blockage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M4521Water in fuel sensor out of range high
The water in fuel sensor signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to supply
- Open sensor ground giving a floating high signal
- Sensor failed high
Checks
- 1Check the ground wire of the water in fuel sensor for continuity
- 2Look at the live reading on the display and see if it sits at the top of its scale
- 3Test the signal wire for stray voltage with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M4522Water in fuel sensor out of range low
The water in fuel sensor signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Open signal wire or missing supply
- Sensor failed low
Checks
- 1Check the supply voltage at the water in fuel sensor plug with the key on
- 2Look at the live reading on the display and see if it sits at the bottom of its scale
- 3Test the signal wire to ground with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M4530Water in fuel sensor fault
The controller reports a fault on the water in fuel without giving a more exact cause in the list. Treat it as a circuit or part failure.· OtherOtherCheck soonCauses
- Failed part
- Wiring or connector problem
- Controller input or output fault
Checks
- 1Check the plug and wiring of the water in fuel for damage and corrosion
- 2Test the part against its normal reading on a matching machine
- 3Have a dealer read the detailed code with the service tool
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M5810Fuel temperature high
The fuel temperature reads above its warning level. The controller flags it so the operator can act before the machine reaches its shutdown limit.· Lost messageLost messageCheck soonCauses
- Real overload or overheat on the system
- Restricted flow or poor cooling
- Sensor reading high
Checks
- 1Verify the real value with a separate gauge or probe before replacing anything
- 2Check cooling, filters and flow in the system the fuel temperature belongs to
- 3Check the sensor wiring if the real value turns out normal
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat M5811Fuel temperature extremely high
The fuel temperature is far above its normal level. The controller may reduce power or shut the machine down to protect it.· OtherOtherStop nowCauses
- Serious overheat or overpressure
- Blocked cooler or relief valve
- Sensor reading extremely high
Checks
- 1Stop the machine and let it cool before testing
- 2Verify the real value with a separate gauge or probe
- 3Check cooler, relief valve and airflow for blockage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M5815Fuel temperature shutdown
The fuel temperature has reached the level at which the controller shuts the machine down or cuts power to protect it.· OtherOtherStop nowCauses
- Condition that stayed in warning until it reached shutdown
- Blocked cooler, filter or line
- Sensor reading in shutdown range
Checks
- 1Do not keep working; fix the underlying fault first
- 2Check the warning codes for the same system that set before this one
- 3Verify the real value with a separate gauge before restarting
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M5826Fuel temperature pre shutdown
The fuel temperature has reached the pre-shutdown level, one step before the controller cuts power. Reduce load and look for the cause now. The list gives the same code a different name on M-Series excavators: "Fuel temperature in shutdown".· OtherOtherCheck soonCauses
- Cooling or flow problem getting worse
- Blocked cooler or low fluid
- Sensor reading high
Checks
- 1Reduce load and let the machine cool
- 2Check cooler, fluid level and airflow
- 3Verify the real value with a separate gauge
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat H9110Fuel pressure at filter inlet too high
The fuel pressure at filter inlet reads above its warning level. The controller flags it so the operator can act before the machine reaches its shutdown limit.· Lost messageLost messageCheck soonCauses
- Real overload or overheat on the system
- Restricted flow or poor cooling
- Sensor reading high
Checks
- 1Verify the real value with a separate gauge or probe before replacing anything
- 2Check cooling, filters and flow in the system the fuel pressure at filter inlet belongs to
- 3Check the sensor wiring if the real value turns out normal
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat H9111Fuel pressure at filter inlet extremely high
The fuel pressure at filter inlet is far above its normal level. The controller may reduce power or shut the machine down to protect it.· OtherOtherStop nowCauses
- Serious overheat or overpressure
- Blocked cooler or relief valve
- Sensor reading extremely high
Checks
- 1Stop the machine and let it cool before testing
- 2Verify the real value with a separate gauge or probe
- 3Check cooler, relief valve and airflow for blockage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat H9121Fuel pressure out of range high
The fuel pressure signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to supply
- Open sensor ground giving a floating high signal
- Sensor failed high
Checks
- 1Check the ground wire of the fuel pressure for continuity
- 2Look at the live reading on the display and see if it sits at the top of its scale
- 3Test the signal wire for stray voltage with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat H9122Fuel pressure out of range low
The fuel pressure signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Open signal wire or missing supply
- Sensor failed low
Checks
- 1Check the supply voltage at the fuel pressure plug with the key on
- 2Look at the live reading on the display and see if it sits at the bottom of its scale
- 3Test the signal wire to ground with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat H9309Fuel pressure low
The fuel pressure reads below its warning level. The controller flags it so the problem can be fixed before the machine reaches its shutdown limit.· Lost messageLost messageCheck soonCauses
- Real low value from leakage or restriction
- Worn pump or low fluid
- Sensor reading low
Checks
- 1Verify the real value with a separate gauge before replacing anything
- 2Check fluid levels and filters in the system the fuel pressure belongs to
- 3Check the sensor wiring if the real value turns out normal
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat M9309Fuel pressure low
The fuel pressure reads below its warning level. The controller flags it so the problem can be fixed before the machine reaches its shutdown limit.· Lost messageLost messageCheck soonCauses
- Real low value from leakage or restriction
- Worn pump or low fluid
- Sensor reading low
Checks
- 1Verify the real value with a separate gauge before replacing anything
- 2Check fluid levels and filters in the system the fuel pressure belongs to
- 3Check the sensor wiring if the real value turns out normal
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat H9314Fuel pressure extremely low
The fuel pressure is far below its normal level. The controller may reduce power or shut the machine down to protect it.· OtherOtherStop nowCauses
- Loss of fluid or pressure
- Pump or supply failure
- Sensor reading extremely low
Checks
- 1Stop the machine and check fluid levels first
- 2Verify the real value with a separate gauge
- 3Check the supply line and pump before suspecting the sensor
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M9314Fuel pressure extremely low
The fuel pressure is far below its normal level. The controller may reduce power or shut the machine down to protect it.· OtherOtherStop nowCauses
- Loss of fluid or pressure
- Pump or supply failure
- Sensor reading extremely low
Checks
- 1Stop the machine and check fluid levels first
- 2Verify the real value with a separate gauge
- 3Check the supply line and pump before suspecting the sensor
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat H9321Fuel pressure out of range high
The fuel pressure signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to supply
- Open sensor ground giving a floating high signal
- Sensor failed high
Checks
- 1Check the ground wire of the fuel pressure for continuity
- 2Look at the live reading on the display and see if it sits at the top of its scale
- 3Test the signal wire for stray voltage with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M9321Fuel pressure out of range high
The fuel pressure signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to supply
- Open sensor ground giving a floating high signal
- Sensor failed high
Checks
- 1Check the ground wire of the fuel pressure for continuity
- 2Look at the live reading on the display and see if it sits at the top of its scale
- 3Test the signal wire for stray voltage with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat H9322Fuel pressure out of range low
The fuel pressure signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Open signal wire or missing supply
- Sensor failed low
Checks
- 1Check the supply voltage at the fuel pressure plug with the key on
- 2Look at the live reading on the display and see if it sits at the bottom of its scale
- 3Test the signal wire to ground with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M9322Fuel pressure out of range low
The fuel pressure signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Open signal wire or missing supply
- Sensor failed low
Checks
- 1Check the supply voltage at the fuel pressure plug with the key on
- 2Look at the live reading on the display and see if it sits at the bottom of its scale
- 3Test the signal wire to ground with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat H9344Fuel pressure derate level 1
The fuel pressure has set derate level 1, meaning the controller cuts engine power in a first step to protect the engine. Fix the restriction before it steps up to level 2.· Real conditionReal conditionCheck soonCauses
- Element or line restricted
- Service overdue
- Sensor reading a false restriction
Checks
- 1Check the service state of the part this code names
- 2Replace the element if it is dirty or overdue
- 3Clear the code and watch whether it returns under load
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M9344Fuel pressure derate level 1
The fuel pressure has set derate level 1, meaning the controller cuts engine power in a first step to protect the engine. Fix the restriction before it steps up to level 2.· Real conditionReal conditionCheck soonCauses
- Element or line restricted
- Service overdue
- Sensor reading a false restriction
Checks
- 1Check the service state of the part this code names
- 2Replace the element if it is dirty or overdue
- 3Clear the code and watch whether it returns under load
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Treat a pressure, water or level code as real until proven otherwise: check the fuel level, drain the water separator and confirm the filter is not blocked.
- 2Unplug the sensor and look for moisture and bent pins; reseat it and clear the code to see whether it comes straight back.
- 3With the key on, measure the 5 V reference and ground at the sensor plug; a missing reference points to the harness or controller, not the sensor.
- 4Check the suction side for air leaks at the lift pump, fittings and filter head, since air gives low-pressure codes without any sensor fault.
- 5Compare the reading on the service screen with the physical condition (a full tank reading empty, for example) before replacing a sensor.
Causes
- Sensor plug corroded or a pin backed out, so the signal floats
- Wiring chafed to the frame or to a supply wire along the tank and filter run
- Real condition behind the code: air leak, blocked filter, water in the bowl or low fuel
- Sensor failed or contaminated by water or debris
Most common here: lost message (5 of 35)
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
When to stop
You'll notice: The fuel gauge reads wrong, a fuel or water warning shows, or the engine is derated or runs rough when the pressure or water condition is real.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
- Bobcat S205 Operation & Maintenance Manual, service codes list
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
