Bobcat · Fuel system
Bobcat Fault Code M0909
Fuel level too low
What does Bobcat code M0909 mean?
The fuel gauge sender says the tank is nearly empty. It is a low-fuel warning, not an engine fault. Urgency: information - a reminder or status message. Check first: if the tank is full, check the sender float for freedom of movement in the tank.
Can I keep running with it?
Information
A reminder or status message. Nothing is failing yet.
What should I check first?
If the tank is full, check the sender float for freedom of movement in the tank
Then 3 more checksWhere this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
Checks
0 of 4 done
Causes
- Fuel pickup or tank slosh baffle issue
- Fuel sender float stuck low
- Sender wire or ground fault
- Gauge calibration error
How it failed
You'll notice: The controller reports that fuel is low.
Real conditionRead from how the source describes the code
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Fuel level, pressure, temperature and water sensors
3 other codes on this part are also real condition (VSE004-01, H9344, M9344). When they show together, start at the wiring and connector they share.
- VSE004-04WIF sensor, voltage below normalShorted lowCheck soon
- 09-09Fuel level lowOtherInformation
- 09-21Fuel level out of range highOtherCheck soon
- 09-22Fuel level out of range lowOtherCheck soon
- M0909Fuel level too lowReal conditionInformation
- M0921Fuel level out of range highOtherCheck soon
- M0922Fuel level out of range lowOtherCheck soon
- P1131-13Fuel filter inlet pressure sensor open circuitOpen circuitCheck soon
- M4510Water in fuel too highLost messageCheck soon
Show the other 26 codesHide the other codes
- VSE002-03Fuel sensor, voltage above normalShorted highCheck soon
- VSE002-04Fuel sensor, voltage below normalShorted lowCheck soon
- VSE004-01WIF sensor, signal below normal rangeReal conditionCheck soon
- VSE004-03WIF sensor, voltage above normalShorted highCheck soon
- M4511Water in fuel extremely highOtherStop now
- M4521Water in fuel sensor out of range highOtherCheck soon
- M4522Water in fuel sensor out of range lowOtherCheck soon
- M4530Water in fuel sensor faultOtherCheck soon
- M5810Fuel temperature highLost messageCheck soon
- M5811Fuel temperature extremely highOtherStop now
- M5815Fuel temperature shutdownOtherStop now
- M5826Fuel temperature pre shutdownOtherCheck soon
- H9110Fuel pressure at filter inlet too highLost messageCheck soon
- H9111Fuel pressure at filter inlet extremely highOtherStop now
- H9121Fuel pressure out of range highOtherCheck soon
- H9122Fuel pressure out of range lowOtherCheck soon
- H9309Fuel pressure lowLost messageCheck soon
- M9309Fuel pressure lowLost messageCheck soon
- H9314Fuel pressure extremely lowOtherStop now
- M9314Fuel pressure extremely lowOtherStop now
- H9321Fuel pressure out of range highOtherCheck soon
- M9321Fuel pressure out of range highOtherCheck soon
- H9322Fuel pressure out of range lowOtherCheck soon
- M9322Fuel pressure out of range lowOtherCheck soon
- H9344Fuel pressure derate level 1Real conditionCheck soon
- M9344Fuel pressure derate level 1Real conditionCheck soon
Related on Equipments Finder
Source
Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
This source lists M0909 and its meaning. The guidance on this page is general, not taken from it.
The source covers: M-Series loaders S450-S850 and T450-T870.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
