EF Logo

JCB fault codes

JCB machines log engine and machine faults as DTCs, read on the instrument cluster or with JCB ServiceMaster. Engine codes follow the P-code pattern; JCB adds its own machine codes.

718 codes in 32 families16 stop now, 673 check soon, 29 info

718 JCB codes - type a code, or a word from the problem.

Covers Backhoe loaders, Telehandlers, Excavators.

Where to look

  1. 01Switch the key on and note any warning lamp or fault icon on the cluster.
  2. 02Connect the JCB diagnostic tool to the machine diagnostic socket.
  3. 03Read active and stored faults for each controller.
  4. 04Fix the cause, then clear the fault and re-test.
How to read JCB fault codes, in full
  1. Switch the key on and note any warning lamp or fault icon on the cluster.
  2. Connect the JCB diagnostic tool (ServiceMaster) to the machine diagnostic socket.
  3. Read active and stored faults for each controller (engine ECU, machine controller, hydraulics, transmission).
  4. Fix the cause, then clear the fault and re-test; a fault that returns needs the full procedure from the service manual.

How urgent is a JCB code?

Stop now16 codes
Shut down and fix before working on. Running on risks damage or the machine locks out.
Check soon673 codes
The machine may derate or limit a function. Find the cause before the next shift.
Information29 codes
A reminder or status message. Nothing is failing yet.

Pick your system

Find the part of the machine, then the family your code belongs to.

Code range
The first and last code in the family, as the machine shows them.
Codes
How many codes the family holds; each is explained on its page.
Severity mix
The share of stop, check and info codes. The dot after it is the most urgent one in the family.

Engine ECU (Dieselmax / Ecomax) - fuel system44 codes

Engine ECU (Dieselmax / Ecomax) - temperature sensors44 codes

Engine ECU (Dieselmax / Ecomax) - injectors53 codes

Engine ECU (Dieselmax / Ecomax) - speed sensors15 codes

Engine ECU (Dieselmax / Ecomax) - air system23 codes

Engine ECU (Dieselmax / Ecomax) - electrical39 codes

Engine ECU (Dieselmax / Ecomax) - ECU29 codes

Engine ECU (Dieselmax / Ecomax) - driver controls26 codes

Communication (CAN / telematics)74 codes

Engine ECU (Dieselmax / Ecomax) - aftertreatment22 codes

Aftertreatment ECU - SCR / DEF208 codes

Hydraulic controller (HECU)64 codes

Machine controller (MECU / DECU)61 codes

Transmission control (TCU)15 codes

Engine ECU (Dieselmax / Ecomax) - engine protection1 code

Most searched JCB codes

Quick answers

How do I read JCB fault codes?

Switch the key on and note any warning lamp or fault icon on the cluster. Connect the JCB diagnostic tool (ServiceMaster) to the machine diagnostic socket.

Which JCB codes mean stop now?

16 of the 718 JCB codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example P0087, P203F-7B, P204F, P0217. 673 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.

What should I check first on a JCB code?

Most JCB codes here (95 of 718) read as open circuit: no current flows, or the signal floats - a wire, pin or coil is broken. First test, as general workshop practice: key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

Which JCB codes are looked up most?

P0002 (rail pressure control error (too high)), P0016 (crank and cam position correlation fault), P0045 (turbo boost control solenoid (evrv) open circuit), P0087 (rail fuel pressure too low), P0088 (rail fuel pressure too high). Each page gives the meaning, the likely causes and the checks.

Sources

Every code was read from these documents and written in our own words.

35 more sources

Other makers

Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.