JCB · Engine ECU (Dieselmax / Ecomax) - air system
JCB Turbo boost control, intake throttle, EGR valve and air filter fault codes
The ECU controls turbo boost through an electronic vacuum regulator (EVRV) and a variable nozzle or wastegate, and compares the result with the boost sensor. The electric throttle actuator on the intake controls air flow for regeneration and EGR.
More about these partsLess
It has a motor, a position sensor and an H-bridge driver in the ECU. The EGR valve lets exhaust gas back into the intake to cut NOx, and a gas temperature sensor lets the ECU check the EGR cooling.
Where this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
What do these codes mean?
JCB codes P0045 to P2528 are all about the turbo boost control, intake throttle, EGR valve and air filter. The most common failure type is shorted high (3 of 23); none needs an immediate stop. Start with this check: check charge air pipes, clamps and the cooler for leaks.
How urgent are they?
None of the 23 codes here means stop now; all 23 can wait until the shift ends, but find the cause before the next one.
- Check soon23
What should I check first?
Check charge air pipes, clamps and the cooler for leaks
Shared checks23 of 23
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
JCB P0045Turbo boost control solenoid (EVRV) open circuit
The ECU sees an open circuit in the turbo boost control solenoid, so boost cannot be regulated.· Open circuitOpen circuitCheck soonCauses
- Open circuit in the boost control solenoid (EVRV) coil
- Broken wire or backed-out pin at the solenoid connector near the turbo
- Heat damage to the harness insulation next to the exhaust
- Corroded connector with high resistance in the control line
- ECU solenoid driver failure, only after wiring and solenoid pass
Checks
- 1Measure the solenoid coil resistance across its two pins with the connector unplugged
- 2Check both control wires for continuity back to the ECU
- 3Inspect the harness for heat damage and the connector for water or corrosion
- 4Run the boost solenoid output test and listen for the click
- 5Wiggle the harness while watching live data for the fault to drop in and out
- 6Look for oil or soot ingress inside the solenoid plug
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB P110CThrottle actuator temperature warning
Throttle actuator temperature warning. This is a status step recorded by the intake throttle actuator logic, so look for the underlying fault that triggered it rather than for a failed part.· OtherOtherCheck soonCauses
- The underlying fault behind this step is still present
- The fault was repaired but the stored status has not been cleared yet
Checks
- 1Read the other active codes first, this status follows from them
- 2After repair, clear the codes and run the machine to confirm the status does not return
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P110DThrottle actuator hardware fault
Throttle actuator hardware fault. The controller logged a fault on the throttle actuator hardware, which affects how the intake throttle actuator works until the cause is found.· OtherOtherCheck soonCauses
- Throttle actuator hardware or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the throttle actuator hardware and look for a value that is stuck or implausible
- 2Check the throttle actuator hardware connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P110EThrottle actuator obstruction fault
Throttle actuator obstruction fault. The controller logged a fault on the throttle actuator obstruction, which affects how the intake throttle actuator works until the cause is found.· OtherOtherCheck soonCauses
- Throttle actuator obstruction or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the throttle actuator obstruction and look for a value that is stuck or implausible
- 2Check the throttle actuator obstruction connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P110FThrottle actuator calibration fault
Throttle actuator calibration fault. The controller logged a fault on the throttle actuator calibration, which affects how the intake throttle actuator works until the cause is found.· Part or controllerPart or controllerCheck soonCauses
- Throttle actuator calibration or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the throttle actuator calibration and look for a value that is stuck or implausible
- 2Check the throttle actuator calibration connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
JCB P140AEGR 2 valve control fault
EGR 2 valve control fault. The controller logged a fault on the EGR 2 valve control, which affects how the EGR valve and gas temperature sensor works until the cause is found.· OtherOtherCheck soonCauses
- EGR 2 valve control or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the EGR 2 valve control and look for a value that is stuck or implausible
- 2Check the EGR 2 valve control connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P140BEGR 2 position sensor fault
EGR 2 position sensor fault. The controller logged a fault on the EGR 2 position sensor, which affects how the EGR valve and gas temperature sensor works until the cause is found.· OtherOtherCheck soonCauses
- EGR 2 position sensor or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the EGR 2 position sensor and look for a value that is stuck or implausible
- 2Check the EGR 2 position sensor connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P140CEGR 2 zero position fault
EGR 2 zero position fault. The controller logged a fault on the EGR 2 zero position, which affects how the EGR valve and gas temperature sensor works until the cause is found.· OtherOtherCheck soonCauses
- EGR 2 zero position or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the EGR 2 zero position and look for a value that is stuck or implausible
- 2Check the EGR 2 zero position connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0234Turbo overboost
Boost pressure is above target (about 4 psi over for 5 seconds). The machine may go into limp mode.· OtherOtherCheck soonCauses
- Turbo wastegate or variable vane actuator sticking so boost cannot be released
- Boost control solenoid (EVRV) failing or its vacuum or air line leaking, stuck in the boost position
- Boost pressure sensor reading too low, so the ECU asks the turbo for more
- Carbon build-up in the turbine vanes
- Blocked or crushed pipe between the actuator and its control source
Checks
- 1Log boost pressure against commanded boost under load and note when it exceeds the target
- 2Check the wastegate or vane actuator moves freely by hand and with the actuator test
- 3Run the boost solenoid output test and listen for the click
- 4Inspect the actuator hose or line for kinks, splits and blockage
- 5Compare the boost sensor reading with a known gauge at the manifold
- 6Check the turbo for oil leaks and for shaft play at the compressor
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0299Turbo low boost
Boost pressure stays well below the target for a sustained time, so the engine feels down on power and may smoke black. The machine may go into limp mode until the boost problem is fixed.· OtherOtherCheck soonCauses
- Boost air leak at a hose, clamp or charge cooler joint
- Blocked air filter or collapsed intake pipe restricting airflow
- Turbo worn, damaged or its actuator stuck open
- Boost solenoid or actuator line leaking so the turbo is not being controlled
- Exhaust leak ahead of the turbo or a blocked DPF or exhaust restricting turbine drive
Checks
- 1Check air filter restriction and replace it if it is dirty
- 2Pressure test the intake pipework and charge cooler and listen for air escape under load
- 3Check the turbo shaft for play and the compressor wheel for damage
- 4Run the actuator test and check the wastegate or vanes move and hold position
- 5Inspect the exhaust manifold and joints for leaks and soot marks
- 6Compare boost to target under load with the diagnostic tool
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0638Intake throttle actuator range/performance
Intake throttle actuator range/performance. The controller sees the intake throttle actuator range/performance behaving outside what it expects, so it logs a range, plausibility or performance fault.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intake throttle actuator range/performance drifting or worn so it no longer matches the real condition
- Poor connection or high resistance in the intake throttle actuator range/performance circuit
- A related fault elsewhere making this reading look wrong
Checks
- 1Compare the intake throttle actuator range/performance value on live data with a known good value or a reference gauge
- 2Check the intake throttle actuator range/performance connector and wiring for high resistance and intermittent contact
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB U1308Throttle actuator CAN communication lost
Throttle actuator CAN communication lost. The controller did not receive a valid message or lost contact on the bus, so data for the intake throttle actuator is missing or unreliable.· Lost messageLost messageCheck soonCauses
- CAN wiring open, shorted or wet at a connector
- The sending module not powered, reset or faulty
Checks
- 1Check the CAN high and low wiring and the 120 ohm termination
- 2Check that the sending module has power, earth and no active faults of its own
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
JCB P1404EGR valve close defective / zero position fault
The EGR valve is not returning to its closed zero position when commanded. The ECU may set a limp mode, raise smoke levels, cause rough running or increase NOx emissions.· OtherOtherCheck soonCauses
- EGR valve stuck partly open by carbon deposits
- Valve actuator or motor failed or its position sensor wrong
- Damaged valve wiring or connector
Checks
- 1Run the EGR valve actuator test and watch the position move to closed and back
- 2Remove the valve and check the poppet for carbon sticking and the seat for damage
- 3Check the valve connector and wires for damage and corrosion
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P2032EGR gas temperature sensor low voltage
EGR gas temperature sensor low voltage. The reading or voltage for the EGR gas temperature sensor is below the allowed range, so the controller treats the signal as unreliable.· Shorted lowShorted lowCheck soonCauses
- EGR gas temperature sensor signal pulled low by a short to ground or an open supply
- Sensor or part failed giving a low reading
Checks
- 1Read the EGR gas temperature sensor value on live data and compare it with the expected value
- 2Unplug the EGR gas temperature sensor and check the signal wire for a short to ground and the supply for 5 V
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JCB P2033EGR gas temperature sensor high voltage
EGR gas temperature sensor high voltage. The reading or voltage for the EGR gas temperature sensor is above the allowed range, so the controller treats the signal as unreliable.· Shorted highShorted highCheck soonCauses
- EGR gas temperature sensor signal pulled high by a short to the 5 V reference or supply
- Sensor or part failed giving a high reading
Checks
- 1Read the EGR gas temperature sensor value on live data and compare it with the expected value
- 2Unplug the EGR gas temperature sensor and check the signal wire for a short to 5 V or battery
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JCB P2100Throttle H-bridge driver internal fault
Throttle H-bridge driver internal fault. The controller logged a fault on the throttle H, which affects how the intake throttle actuator works until the cause is found.· Part or controllerPart or controllerCheck soonCauses
- Throttle H or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the throttle H and look for a value that is stuck or implausible
- 2Check the throttle H connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
JCB P2101Throttle H-bridge driver short circuit
Throttle H-bridge driver short circuit. The controller found the throttle H output or circuit shorted and drawing too much current, so it protects the driver.· Short circuitShort circuitCheck soonCauses
- Throttle H coil shorted internally, drawing too much current
- Harness chafed through and touching the frame or a supply wire near the throttle H
- Water in the throttle H connector
Checks
- 1Unplug the throttle H and measure its resistance, looking for a very low reading
- 2Check each wire for a short to ground and to battery with the plug removed
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB P2102Throttle H-bridge driver short to ground
Throttle H-bridge driver short to ground. The throttle H circuit is pulled down to ground, so the controller sees the signal or output stuck low.· Shorted lowShorted lowCheck soonCauses
- Wire for the throttle H chafed and touching chassis or engine ground
- Throttle H coil or sensor shorted internally
Checks
- 1Unplug the throttle H and check each wire for a short to chassis ground
- 2Measure the resistance of the throttle H and compare it with the manual value
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JCB P2103Throttle H-bridge driver short to battery
Throttle H-bridge driver short to battery. The throttle H circuit is being pulled up to battery or supply voltage, so the controller cannot read or drive it correctly.· Shorted highShorted highCheck soonCauses
- Wire for the throttle H touching a battery-fed wire in the harness
- Water or damage inside the throttle H connector bridging to supply
Checks
- 1Unplug the throttle H and check the signal wire for voltage with the key on, any battery voltage means a short to supply
- 2Inspect the harness for chafing where it crosses live wires near the throttle H
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JCB P2119Throttle learned position fault
Throttle learned position fault. The controller sees the throttle learned position behaving outside what it expects, so it logs a range, plausibility or performance fault.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Throttle learned position drifting or worn so it no longer matches the real condition
- Poor connection or high resistance in the throttle learned position circuit
- A related fault elsewhere making this reading look wrong
Checks
- 1Compare the throttle learned position value on live data with a known good value or a reference gauge
- 2Check the throttle learned position connector and wiring for high resistance and intermittent contact
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P2280Engine air filter blocked
The ECU saw a high restriction on the intake side of the engine, which usually means the air filter element is blocked with dust. A blocked filter starves the engine of air, so it smokes and loses power until the filter is cleaned or replaced.· Real conditionReal conditionCheck soonCauses
- Air filter element blocked with dust or chaff
- Air filter restriction sensor or switch failed
- Intake pipe collapsed or blocked by debris
- Filter housing or pre-cleaner packed with dirt
Checks
- 1Inspect the air filter element and replace it if it is dirty or oily
- 2Check the intake pipe and pre-cleaner for debris and collapsed hoses
- 3Measure the restriction signal on live data with a clean filter fitted
- 4Check the restriction sensor connector and wiring for corrosion
- 5Look for dust marks inside the intake that point to a leak after the filter
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JCB P2527EVRV vacuum sensor voltage too low
EVRV vacuum sensor voltage too low. The reading or voltage for the EVRV vacuum sensor voltage too is below the allowed range, so the controller treats the signal as unreliable.· Shorted lowShorted lowCheck soonCauses
- EVRV vacuum sensor voltage too signal pulled low by a short to ground or an open supply
- Sensor or part failed giving a low reading
Checks
- 1Read the EVRV vacuum sensor voltage too value on live data and compare it with the expected value
- 2Unplug the EVRV vacuum sensor voltage too and check the signal wire for a short to ground and the supply for 5 V
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JCB P2528EVRV vacuum sensor voltage too high
EVRV vacuum sensor voltage too high. The reading or voltage for the EVRV vacuum sensor voltage too is above the allowed range, so the controller treats the signal as unreliable.· Shorted highShorted highCheck soonCauses
- EVRV vacuum sensor voltage too signal pulled high by a short to the 5 V reference or supply
- Sensor or part failed giving a high reading
Checks
- 1Read the EVRV vacuum sensor voltage too value on live data and compare it with the expected value
- 2Unplug the EVRV vacuum sensor voltage too and check the signal wire for a short to 5 V or battery
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Shared checks
Checks, in order
- 1Check charge air pipes, clamps and the cooler for leaks
- 2Check the actuator moves freely and look for soot build-up
- 3Check the EGR valve for sticking or soot (on the EGR valve and gas temperature sensor, with the diagnostic tool and a multimeter)
- 4Test the EVRV and its vacuum hose and see that the actuator moves freely
- 5Measure motor resistance and check the wires for opens and shorts
- 6Run the EGR test on the diagnostic tool (on the EGR valve and gas temperature sensor, with the diagnostic tool and a multimeter)
- 7Compare the boost sensor reading with a gauge under load
Causes
- Boost leak in the charge air pipes or cooler
- Actuator motor or gearing stuck or worn with soot
- EGR valve stuck with soot
- Turbo actuator or EVRV stuck or its vacuum line split
Most common here: shorted high (3 of 23)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: The engine may lose power, smoke or surge if boost is too low or too high, and a check lamp is on.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Partao JCB fault code P0234 page
- Partao JCB fault code P0045 page
- Partao JCB fault code list, page 9 (code table)
- Partao JCB fault code P0299 page
- Partao JCB fault code list, page 8 (code table)
- Partao JCB fault code list, page 16 (code table)
- Partao JCB fault code list, page 10 (code table)
- Partao JCB fault code list, page 12 (code table)
- Partao JCB fault code list, page 13 (code table)
- Partao JCB fault code list, page 14 (code table)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
