EF Logo

Boom loader capacity at reach: telehandler load chart

A telehandler's capacity falls as the boom goes out and up. Pick the machine, enter the reach and height, and read the rated capacity from the maker's own load chart.

The formula

Capacity = the maker's chart zone at your reach and height; near a zone line the lower zone is used. Outside the chart there is no rated lift.

What it works out

The rated capacity of a telehandler at a reach and height, read from the maker's load chart.

Why it matters

Capacity falls as the boom goes out: a 4 t machine may lift little more than 1 t at full reach.

How to use it

  1. Choose the Machine and Chart. Each one is the maker’s chart for standard forks, with the stabilisers down where the machine has them.
  2. Enter the Forward Reach: the distance from the front of the front tyres to the centre of the load, as the chart measures it.
  3. Enter the Lift Height: the height of the forks above the ground where the load is placed or picked.
  4. Enter Your Load, including the pallet and any slings, to see the share of the chart capacity it uses.
  5. Read the capacity and the zone on the chart drawing, then check the same point on the chart in the cab before you lift.

Quick reference

Printable chart

Rated capacity by reach at 2 m lift height

Reach (m)540-140540-170535-125533-105
34,000 kg4,000 kg3,500 kg2,500 kg
44,000 kg4,000 kg2,500 kg2,000 kg
53,500 kg3,000 kg2,000 kg1,500 kg
62,500 kg2,500 kg1,500 kg1,250 kg
72,000 kg2,000 kg1,500 kg0 kg
81,500 kg1,500 kg1,150 kg0 kg
91,250 kg1,000 kg0 kg0 kg
100 kg1,000 kg0 kg0 kg

Stabilisers down, standard forks, read from each maker’s chart. 0 kg means the point is outside that machine’s chart.

How the capacity is read

There is no formula here. The tool finds the zone of the maker's load chart that your reach and height fall in, and that zone's figure is the rated capacity. The zones were taken from the vector drawing in the maker's specification sheet and placed on the chart's own metre grid. Where your point is within 0.1 m of a zone line, the lower zone is used, so a reading never rounds up. Outside the drawn chart the machine has no rated capacity at all: the tool shows 0 kg and says so.

Why a generic formula is unsafe

It is tempting to scale the headline capacity by reach, as with a forklift's load centre. A telehandler does not work that way. Its limit at each point is the lower of two things the maker tests: tipping forward (the load's moment about the front axle against the machine's counterweight, under EN 1459 or ISO 22915-14) and the strength of the boom, its sections and the hydraulics, which changes with how far the boom is extended and how high it is raised. The zone lines on a chart bend for that reason, and no simple ratio follows them. A guessed figure can be thousands of kilograms too high at height, so a reading without the chart is not given.

Stabilisers, attachments and the LMI

With the stabilisers up the same machine lifts far less: JCB rates a 540-140 at 3,000 kg to full height with stabilisers down but 1,500 kg with them up, and 1,250 kg against 150 kg at full reach. Buckets, jibs, winches and work platforms each have their own chart, and so may different tyres or serial ranges. The chart fixed in the cab and the machine's load moment indicator (LMI) are what decide a lift; if the LMI cuts out, the load is too heavy for where it is.

Worked examples

  • A JCB 540-140 placing 1,500 kg at 4 m reach and 6 m height is in the 3,500 kg zone, using 42.86 % of it with 2,000 kg to spare.
  • The same 1,500 kg at 9 m reach, near the ground, is over the chart: the zone there is 1,250 kg, so the load would be 120 % of it.
  • A JCB 540-170 lifting 1,000 kg of blocks at 8 m reach and 10 m height reads 1,500 kg, leaving 500 kg. Its chart reaches 12.5 m and 16.7 m.
  • A compact Genie GTH-5519 rated 2,500 kg close in reads 1,361 kg at 2 m reach and 3 m height, so a 1,200 kg pallet uses 88.17 %.

Frequently asked questions

What is the capacity of a boom loader?

The headline figure is only the maximum, close in: 4,000 kg for a JCB 540-140 or 540-170, 3,500 kg for a 535-125 or 535-140. At full reach the 540-140 is rated 1,250 kg with stabilisers down, so the capacity that matters is the one at your reach and height.

How do I read a telehandler load chart?

Find the load’s reach along the bottom and its height up the side. The zone where they meet gives the most the machine may lift there. If the point falls between zones, use the lower one; if it falls outside the chart, the lift is not allowed.

Why does capacity drop with reach?

The further out the load, the larger its tipping moment about the front axle, and the more the extended boom has to carry. Both limits tighten together, which is why the zones step down as the boom extends.

Can I use a formula instead of the load chart?

No. The chart combines stability and structural limits the maker tested for that machine and setup. A ratio or a load-centre formula can overstate the capacity badly, especially high up.

Which telehandler models are included?

JCB 540-140, 540-170, 535-140, 535-125 and 533-105, and the Genie GTH-5519. Charts that could not be read reliably, such as the JCB 531-70 and the Manitou MRT and MT ranges, are left out rather than guessed.

Do stabilisers change the capacity?

Yes, a lot. These charts are with stabilisers down. With them up, the 540-140 is rated 1,500 kg to full height and 150 kg at full reach, against 3,000 kg and 1,250 kg with them down.

Sources

  1. JCB Loadall construction range specification, 2023 (531-70 to 540-200): 540-140, 540-170 and 533-105 charts
  2. JCB Loadall 535-125 / 535-140 HiViz specification 9999/5401 (01/11)
  3. Genie GTH-5519 specifications, Part No. 109416 (February 2015)

Add this calculator to your website

Copy the code and paste it into your page. The calculator is free and works as it does here.

<iframe src="https://www.equipmentsfinder.com/embed/field-tools/telehandler-capacity-at-reach" title="Boom loader capacity at reach: telehandler load chart" width="100%" height="620" style="border:0;max-width:720px" loading="lazy"></iframe>
<p style="font-size:12px"><a href="https://www.equipmentsfinder.com/field-tools/telehandler-capacity-at-reach">Boom loader capacity at reach: telehandler load chart</a> by <a href="https://www.equipmentsfinder.com">EquipmentsFinder</a></p>
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.