JCB · Engine ECU (Dieselmax / Ecomax) - air system
JCB Fault Code P0299
Turbo low boost
What does JCB code P0299 mean?
Boost pressure stays well below the target for a sustained time, so the engine feels down on power and may smoke black. The machine may go into limp mode until the boost problem is fixed. Urgency: check soon - the machine may derate or limit a function. Check first: check air filter restriction and replace it if it is dirty.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check air filter restriction and replace it if it is dirty
Then 5 more checksWhere this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
Checks
0 of 6 done
Causes
- Boost air leak at a hose, clamp or charge cooler joint
- Blocked air filter or collapsed intake pipe restricting airflow
- Turbo worn, damaged or its actuator stuck open
- Boost solenoid or actuator line leaking so the turbo is not being controlled
1 more causeFewer causes
- Exhaust leak ahead of the turbo or a blocked DPF or exhaust restricting turbine drive
How it failed
You'll notice: The engine feels flat under load, may smoke black and does not pull as it should.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Turbo boost control, intake throttle, EGR valve and air filter
- P140AEGR 2 valve control faultOtherCheck soon
- P140BEGR 2 position sensor faultOtherCheck soon
- P140CEGR 2 zero position faultOtherCheck soon
- P0234Turbo overboostOtherCheck soon
- P0299Turbo low boostOtherCheck soon
- P0638Intake throttle actuator range/performanceErratic or implausibleCheck soon
- U1308Throttle actuator CAN communication lostLost messageCheck soon
- P1404EGR valve close defective / zero position faultOtherCheck soon
- P2032EGR gas temperature sensor low voltageShorted lowCheck soon
Show the other 14 codesHide the other codes
- P0045Turbo boost control solenoid (EVRV) open circuitOpen circuitCheck soon
- P110CThrottle actuator temperature warningOtherCheck soon
- P110DThrottle actuator hardware faultOtherCheck soon
- P110EThrottle actuator obstruction faultOtherCheck soon
- P110FThrottle actuator calibration faultPart or controllerCheck soon
- P2033EGR gas temperature sensor high voltageShorted highCheck soon
- P2100Throttle H-bridge driver internal faultPart or controllerCheck soon
- P2101Throttle H-bridge driver short circuitShort circuitCheck soon
- P2102Throttle H-bridge driver short to groundShorted lowCheck soon
- P2103Throttle H-bridge driver short to batteryShorted highCheck soon
- P2119Throttle learned position faultErratic or implausibleCheck soon
- P2280Engine air filter blockedReal conditionCheck soon
- P2527EVRV vacuum sensor voltage too lowShorted lowCheck soon
- P2528EVRV vacuum sensor voltage too highShorted highCheck soon
Other JCB codes: Engine ECU (Dieselmax / Ecomax) - air system
Related on Equipments Finder
Source
Partao JCB fault code P0299 page
This source lists P0299 and its meaning. The guidance on this page is general, not taken from it.
The source covers: JS excavators, Loadall telehandlers (incl. 540-140), backhoe loaders.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
