JCB · Engine ECU (Dieselmax / Ecomax) - temperature sensors
JCB Intake air temperature, manifold boost and barometric sensors fault codes
The intake air, boost (TMAP) and ambient air temperature sensors are thermistors that tell the ECU how warm the air is before and after the turbo and outside the machine. The ECU uses them to correct fuelling and boost.
More about these partsLess
These sensors read air pressure around the engine, in the intake manifold and after the turbocharger. The ECU uses them to correct fuelling for altitude and boost and to control the turbo.
Where this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
What do these codes mean?
JCB codes 0x3D to P2229 are all about the intake air temperature, manifold boost and barometric sensors. The most common failure type is erratic or implausible (6 of 26); none needs an immediate stop. Start with this check: compare each reading with the real air temperature on a cold engine.
How urgent are they?
None of the 26 codes here means stop now; all 26 can wait until the shift ends, but find the cause before the next one.
- Check soon26
What should I check first?
Compare each reading with the real air temperature on a cold engine
Shared checks26 of 26
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
JCB 0x3DErroneous signal for barometric pressure
Erroneous signal for barometric pressure. The controller logged a fault on the erroneous signal for barometric pressure, which affects how the manifold, boost or barometric pressure sensor works until the cause is found.· OtherOtherCheck soonCauses
- Erroneous signal for barometric pressure or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the erroneous signal for barometric pressure and look for a value that is stuck or implausible
- 2Check the erroneous signal for barometric pressure connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P007ATMAP temperature element sensor fault
TMAP temperature element sensor fault. The controller logged a fault on the TMAP temperature element sensor, which affects how the air temperature sensor works until the cause is found.· OtherOtherCheck soonCauses
- TMAP temperature element sensor or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the TMAP temperature element sensor and look for a value that is stuck or implausible
- 2Check the TMAP temperature element sensor connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0071-87Missing ambient air temperature message
Missing ambient air temperature message. The controller did not receive a valid message or lost contact on the bus, so data for the air temperature sensor is missing or unreliable.· Lost messageLost messageCheck soonCauses
- CAN wiring open, shorted or wet at a connector
- The sending module not powered, reset or faulty
Checks
- 1Check the CAN high and low wiring and the 120 ohm termination
- 2Check that the sending module has power, earth and no active faults of its own
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
JCB P0095Intake air temperature sensor 2 circuit fault
Intake air temperature sensor 2 circuit fault. The controller logged a fault on the intake air temperature sensor 2 circuit, which affects how the air temperature sensor works until the cause is found.· OtherOtherCheck soonCauses
- Intake air temperature sensor 2 circuit or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the intake air temperature sensor 2 circuit and look for a value that is stuck or implausible
- 2Check the intake air temperature sensor 2 circuit connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0096Intake air temperature sensor 2 range/performance
Intake air temperature sensor 2 range/performance. The controller sees the intake air temperature sensor 2 range/performance behaving outside what it expects, so it logs a range, plausibility or performance fault.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intake air temperature sensor 2 range/performance drifting or worn so it no longer matches the real condition
- Poor connection or high resistance in the intake air temperature sensor 2 range/performance circuit
- A related fault elsewhere making this reading look wrong
Checks
- 1Compare the intake air temperature sensor 2 range/performance value on live data with a known good value or a reference gauge
- 2Check the intake air temperature sensor 2 range/performance connector and wiring for high resistance and intermittent contact
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0097Intake air temperature sensor 2 signal low
Intake air temperature sensor 2 signal low. The reading or voltage for the intake air temperature sensor 2 is below the allowed range, so the controller treats the signal as unreliable.· OtherOtherCheck soonCauses
- Intake air temperature sensor 2 signal pulled low by a short to ground or an open supply
- Sensor or part failed giving a low reading
Checks
- 1Read the intake air temperature sensor 2 value on live data and compare it with the expected value
- 2Unplug the intake air temperature sensor 2 and check the signal wire for a short to ground and the supply for 5 V
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0098Intake air temperature sensor 2 signal high
Intake air temperature sensor 2 signal high. The reading or voltage for the intake air temperature sensor 2 is above the allowed range, so the controller treats the signal as unreliable.· OtherOtherCheck soonCauses
- Intake air temperature sensor 2 signal pulled high by a short to the 5 V reference or supply
- Sensor or part failed giving a high reading
Checks
- 1Read the intake air temperature sensor 2 value on live data and compare it with the expected value
- 2Unplug the intake air temperature sensor 2 and check the signal wire for a short to 5 V or battery
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0099Intake air temperature sensor 2 intermittent or erratic
Intake air temperature sensor 2 intermittent or erratic. The controller logged a fault on the intake air temperature sensor 2 intermittent or erratic, which affects how the air temperature sensor works until the cause is found.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intake air temperature sensor 2 intermittent or erratic or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the intake air temperature sensor 2 intermittent or erratic and look for a value that is stuck or implausible
- 2Check the intake air temperature sensor 2 intermittent or erratic connector and wiring for damage
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB C102AAmbient air temperature sensor open circuit
Ambient air temperature sensor open circuit. The controller finds no current path in the ambient air temperature sensor circuit, so the air temperature sensor cannot be driven or read as expected.· Open circuitOpen circuitCheck soonCauses
- Open wire or pushed-back pin between the controller and the ambient air temperature sensor
- Ambient air temperature sensor coil, element or sensor internally open
Checks
- 1Unplug the ambient air temperature sensor and measure across its pins, an open reading means the part is faulty
- 2Check continuity of each wire from the ambient air temperature sensor plug to the controller pin
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB P0105MAP / barometric pressure circuit fault
The ECU sees a missing or implausible signal from the manifold pressure / baro sensor (T-MAP on JCB machines).· Erratic or implausibleErratic or implausibleCheck soonCauses
- Combined T-MAP sensor failed or its pressure element drifting
- Blocked or cracked sensor port, or a leaking pipe between the intake manifold and the sensor
- Loose, corroded or damaged sensor connector
Checks
- 1Read the T-MAP pressure with key on and engine off and confirm it matches local barometric pressure
- 2Check the sensor port and the pipe to the manifold for blockage, cracks or loose clamps
- 3Inspect the connector for corrosion and check all wires to the ECU for continuity
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0106MAP / barometric pressure range/performance
MAP / barometric pressure range/performance. The controller sees the MAP / barometric pressure range/performance behaving outside what it expects, so it logs a range, plausibility or performance fault.· Erratic or implausibleErratic or implausibleCheck soonCauses
- MAP / barometric pressure range/performance drifting or worn so it no longer matches the real condition
- Poor connection or high resistance in the MAP / barometric pressure range/performance circuit
- A related fault elsewhere making this reading look wrong
Checks
- 1Compare the MAP / barometric pressure range/performance value on live data with a known good value or a reference gauge
- 2Check the MAP / barometric pressure range/performance connector and wiring for high resistance and intermittent contact
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0110Intake air temperature sensor 1 circuit fault
The ECU sees a fault in the intake air temperature sensor circuit, with a reading out of range or missing. Expect slightly poor cold starting, a little more smoke or reduced power in extreme temperatures.· OtherOtherCheck soonCauses
- Intake air temperature sensor failed or drifting
- Damaged wire or loose connector on the intake air temperature sensor
- Sensor in the intake pipe damaged by oil or dirt
Checks
- 1Read the live intake temperature and compare it with ambient temperature on a cold engine
- 2Inspect the sensor and its tip for oil, dirt or physical damage
- 3Check the connector for corrosion and spread pins
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0111Intake air temperature sensor 1 signal low
The intake air temperature sensor signal reads too low, which the ECU interprets as very hot air. It may cause poor cold starts, slight power loss and a stored warning on the machine display.· Real conditionReal conditionCheck soonCauses
- Signal wire shorted to ground
- Intake air temperature sensor shorted internally
- Water in the sensor connector bridging the signal to ground
Checks
- 1Check the live reading against ambient and confirm it is impossibly hot
- 2Unplug the sensor and see the reading swing to the opposite extreme
- 3Check the signal wire for a short to ground with the connector unplugged
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JCB P0113Intake air temperature sensor 1 signal high
IAT sensor signal reads too high, which looks like very cold air and points to an open circuit.· Open circuitOpen circuitCheck soonCauses
- Open circuit in the intake air temperature sensor loop, usually at the pipe-side connector
- Sensor plug off or its terminals loose in the intake pipe housing
- Air temperature signal wire touching the 5 V reference or a supply wire
Checks
- 1Check the live air temperature on a hot day and confirm it sits at the minimum value
- 2Make sure the sensor plug is fitted and the terminals are clean and tight
- 3Check the signal wire for continuity from the plug to the ECU
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JCB P0124Intake air temperature sensor 1 intermittent or high signal
Intake air temperature sensor 1 intermittent or high signal. The reading or voltage for the intake air temperature sensor 1 intermittent or is above the allowed range, so the controller treats the signal as unreliable.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intake air temperature sensor 1 intermittent or signal pulled high by a short to the 5 V reference or supply
- Sensor or part failed giving a high reading
Checks
- 1Read the intake air temperature sensor 1 intermittent or value on live data and compare it with the expected value
- 2Unplug the intake air temperature sensor 1 intermittent or and check the signal wire for a short to 5 V or battery
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0235Boost pressure sensor circuit fault
The ECU found a fault in the boost pressure sensor circuit, a signal out of range or missing. Fuelling and turbo control then run on defaults, so expect reduced power and possibly limp mode.· OtherOtherCheck soonCauses
- Boost pressure sensor failed or drifting out of range
- Sensor connector loose, corroded or damaged
- Blocked sensor port or a split hose feeding the sensor
Checks
- 1Read the boost pressure with key on and engine off and confirm it equals atmospheric pressure
- 2Check the sensor port and its hose for blockage or leaks
- 3Inspect the plug for corrosion and the wires for chafing
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0236Boost pressure sensor range/performance
Boost pressure sensor range/performance. The controller sees the boost pressure sensor range/performance behaving outside what it expects, so it logs a range, plausibility or performance fault.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Boost pressure sensor range/performance drifting or worn so it no longer matches the real condition
- Poor connection or high resistance in the boost pressure sensor range/performance circuit
- A related fault elsewhere making this reading look wrong
Checks
- 1Compare the boost pressure sensor range/performance value on live data with a known good value or a reference gauge
- 2Check the boost pressure sensor range/performance connector and wiring for high resistance and intermittent contact
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0237Boost pressure sensor signal low
The boost pressure sensor signal voltage is below the expected range, so the ECU thinks there is no boost. It then uses default fuelling and the machine may lose power or enter limp mode.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Open 5 V reference to the boost sensor so it outputs a very low signal
- Boost pressure sensor failed low
Checks
- 1With key on, probe the boost sensor plug for the 5 V reference and confirm it is present
- 2Check the signal wire for a short to ground with the connector unplugged
- 3Check the signal wire is continuous from the plug to the ECU pin
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0238Boost pressure sensor signal high
The boost pressure sensor signal voltage is above the expected range, so the ECU thinks boost is extremely high. It may cut fuel or go into limp mode to protect the engine.· OtherOtherCheck soonCauses
- Signal wire shorted to the 5 V reference or to supply
- Open ground or return on the boost sensor, letting the signal float high
- Boost pressure sensor failed high
Checks
- 1Read the live boost value with the engine off and see if it is high when it should be zero
- 2Unplug the sensor and see whether the reading drops, which points to the wiring or the sensor
- 3Check the signal wire for a short to supply with the ECU unplugged
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB C1029Ambient air temperature sensor short circuit
Ambient air temperature sensor short circuit. The controller found the ambient air temperature sensor output or circuit shorted and drawing too much current, so it protects the driver.· Short circuitShort circuitCheck soonCauses
- Ambient air temperature sensor coil shorted internally, drawing too much current
- Harness chafed through and touching the frame or a supply wire near the ambient air temperature sensor
- Water in the ambient air temperature sensor connector
Checks
- 1Unplug the ambient air temperature sensor and measure its resistance, looking for a very low reading
- 2Check each wire for a short to ground and to battery with the plug removed
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
JCB P1112Boost temperature sensor low voltage
Boost temperature sensor low voltage. The reading or voltage for the boost temperature sensor is below the allowed range, so the controller treats the signal as unreliable.· Shorted lowShorted lowCheck soonCauses
- Boost temperature sensor signal pulled low by a short to ground or an open supply
- Sensor or part failed giving a low reading
Checks
- 1Read the boost temperature sensor value on live data and compare it with the expected value
- 2Unplug the boost temperature sensor and check the signal wire for a short to ground and the supply for 5 V
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JCB P1113Boost temperature sensor high voltage
Boost temperature sensor high voltage. The reading or voltage for the boost temperature sensor is above the allowed range, so the controller treats the signal as unreliable.· Shorted highShorted highCheck soonCauses
- Boost temperature sensor signal pulled high by a short to the 5 V reference or supply
- Sensor or part failed giving a high reading
Checks
- 1Read the boost temperature sensor value on live data and compare it with the expected value
- 2Unplug the boost temperature sensor and check the signal wire for a short to 5 V or battery
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JCB P2226Barometric pressure sensor A circuit fault
Barometric pressure sensor A circuit fault. The controller logged a fault on the barometric pressure sensor A circuit, which affects how the manifold, boost or barometric pressure sensor works until the cause is found.· OtherOtherCheck soonCauses
- Barometric pressure sensor A circuit or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the barometric pressure sensor A circuit and look for a value that is stuck or implausible
- 2Check the barometric pressure sensor A circuit connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P2227-00Barometric sensor fault
Barometric sensor fault. The controller logged a fault on the barometric sensor, which affects how the manifold, boost or barometric pressure sensor works until the cause is found.· OtherOtherCheck soonCauses
- Barometric sensor or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the barometric sensor and look for a value that is stuck or implausible
- 2Check the barometric sensor connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P2228Barometric pressure sensor signal low
Barometric pressure sensor signal low. The reading or voltage for the barometric pressure sensor is below the allowed range, so the controller treats the signal as unreliable.· OtherOtherCheck soonCauses
- Barometric pressure sensor signal pulled low by a short to ground or an open supply
- Sensor or part failed giving a low reading
Checks
- 1Read the barometric pressure sensor value on live data and compare it with the expected value
- 2Unplug the barometric pressure sensor and check the signal wire for a short to ground and the supply for 5 V
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P2229Barometric pressure sensor signal high
Barometric pressure sensor signal high. The reading or voltage for the barometric pressure sensor is above the allowed range, so the controller treats the signal as unreliable.· OtherOtherCheck soonCauses
- Barometric pressure sensor signal pulled high by a short to the 5 V reference or supply
- Sensor or part failed giving a high reading
Checks
- 1Read the barometric pressure sensor value on live data and compare it with the expected value
- 2Unplug the barometric pressure sensor and check the signal wire for a short to 5 V or battery
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Compare each reading with the real air temperature on a cold engine
- 2With the engine off the reading should match local air pressure
- 3Measure the sensor resistance and compare it with the manual curve
- 4Check the sensor port and hose for oil, soot or a split
- 5Check the signal wire for a short to ground or to the 5 V supply
- 6Measure the supply and signal at the plug against the ECU pin out
- 7Compare the intake sensors with each other, since they should read close on a cold engine
Causes
- Sensor failed or drifting
- Sensor failed or its port blocked with oil or soot
- Corroded connector
- Boost hose split giving a false reading
Most common here: erratic or implausible (6 of 26)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: A check lamp comes on and the engine may smoke or lose a little power in hot or cold weather.
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Partao JCB fault code list, page 4 (code table)
- Partao JCB fault code list, page 1 (code table)
- Partao JCB fault code list, page 2 (code table)
- Partao JCB fault code P0105 page
- Partao JCB fault code list, page 5 (code table)
- Partao JCB fault code list, page 9 (code table)
- Partao JCB fault code list, page 13 (code table)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
