Skyjack fault codes
Skyjack SJIII scissors flash a two-part code on the GP102 module LED; newer Skycoded machines show a three-digit number with a message. The on-board charger has its own F and E codes.
81 codes in 5 families12 stop now, 53 check soon, 16 info
81 Skyjack codes - type a code, or a word from the problem.
Covers Scissor lifts.
Where to look
- 01Find the LED on the GP102 module or the display and keypad in the hydraulic tray.
- 02For a flash code count the first group of quarter-second flashes, wait for the 1.5…
- 03Only one code is reported at a time, so fix it and read again, since another fault…
- 04For the charger read the three LEDs, or the F and E number on its display, using the…
- 05For Deutz engine codes on boom lifts hold the diagnostic switch on the base console…
How to read Skyjack fault codes, in full
- Find the LED on the GP102 module (older SJIII scissors) or the display and keypad in the hydraulic tray (Skycoded machines).
- For a flash code count the first group of quarter-second flashes, wait for the 1.5 second gap, then count the second group; a 4 second pause ends the pattern, which then repeats.
- Only one code is reported at a time, so fix it and read again, since another fault may then show.
- For the charger read the three LEDs, or the F and E number on its display, using the charger entries.
- For Deutz engine codes on boom lifts hold the diagnostic switch on the base console with the key on and count the flashes, then check the Skyjack manual for your serial number.
How urgent is a Skyjack code?
- Stop now12 codes
- Shut down and fix before working on. Running on risks damage or the machine locks out.
- Check soon53 codes
- The machine may derate or limit a function. Find the cause before the next shift.
- Information16 codes
- A reminder or status message. Nothing is failing yet.
Pick your system
Find the part of the machine, then the family your code belongs to.
- Code range
- The first and last code in the family, as the machine shows them.
- Codes
- How many codes the family holds; each is explained on its page.
- Severity mix
- The share of stop, check and info codes. The dot after it is the most urgent one in the family.
GP102 module LED flash codes65 codes
On-board battery charger codes16 codes
Most searched Skyjack codes
- F-0-0-1Charger fault: DC-DC (LLC) excessive leakage
- E-0-0-2Charger error: battery voltage too low to start
- E-0-0-3Charger error: charge time limit reached
- 1-1Vehicle tilted
- 1-2Vehicle overloaded
- 2-1Elevation switch shifted?
- 3 LEDs, 1 blinkCharger LEDs: 3 blinks, output connection error
- 3 LEDs, 2 blinkCharger LEDs: 2 blinks, AC voltage out of range
- 3 LEDs, 3 blinkCharger LEDs: 3 blinks, charger overheated
- 3 LEDs, 4 blinkCharger LEDs: 4 blinks, over-current
- 4-1P4-1 or P5-1 short to 0 V
- 5-1B+ supply too low
- 6-1Height not calibrated
- 6-2Load not calibrated
- 6-3No last calibration date
- 7-1Bad tilt sensor
- 100% LED blinkingCharger LEDs: 100% LED blinking, 18 hour timer
- 111PINPAD (enter pinpad code)
- 137LOW BATTERY (shows when lift is attempted)
- P1070 SPN 598 FMI 10Deutz engine code: clutch signal abnormal rate of change
Quick answers
How do I read Skyjack fault codes?
Find the LED on the GP102 module (older SJIII scissors) or the display and keypad in the hydraulic tray (Skycoded machines). For a flash code count the first group of quarter-second flashes, wait for the 1.5 second gap, then count the second group; a 4 second pause ends the pattern, which then repeats.
Which Skyjack codes mean stop now?
12 of the 81 Skyjack codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example F-0-0-1, 4-1, F-0-0-2, F-0-0-3. 53 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.
What should I check first on a Skyjack code?
Most Skyjack codes here (8 of 81) read as lost message: a module stopped hearing another on the data link, or the data came late or garbled. First test, as general workshop practice: key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Which Skyjack codes are looked up most?
F-0-0-1 (charger fault: dc-dc (llc) excessive leakage), E-0-0-2 (charger error: battery voltage too low to start), E-0-0-3 (charger error: charge time limit reached), 1-1 (vehicle tilted), 1-2 (vehicle overloaded). Each page gives the meaning, the likely causes and the checks.
Sources
Every code was read from these documents and written in our own words.
- Skyjack SJIII 3215/3219 Service Manual 155147AD (Nov 2013), sections 5.3-2 and 5.3-3, LED Error Codes, pp. 9-11
- Skyjack SJIII 3220/3226/4620/4626/4632 Service Manual 157928AM (Apr 2019), section 5 Charger Troubleshooting, pp. 133-135
- Skyjack SJIII 3215/3219 Service Manual 155147AD (Nov 2013), section 5.3-5 Control Module Load Calibration - Code Messages & Definitions, pp. 13-16
- Skyjack SJIII DC Electric Scissors Operating Manual 194849AGA (Nov 2022), section 3, battery charger, p. 57
- Skyjack Tech Tip March 2026 - Skycoded 111: Enter Pinpad Code
- Skyjack Tech Tip February 2026 - Skycoded Scissor 137: Low Battery Code
Other makers
Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.
Post a request