Volvo and Mack truck fault codes
Volvo and Mack trucks report faults by the control unit (MID) and what failed in it - a parameter (PID), a component (SID) or a maker-specific item (PSID) - with a failure mode (FMI).
174 codes in 39 families25 stop now, 146 check soon, 3 info
174 Volvo/Mack codes - type a code, or a word from the problem.
Covers Trucks, Tractor units.
Where to look
- 01Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and…
- 02Note the whole code as MID, then PID/SID/PPID/PSID, then FMI, and whether it is…
- 03Use the FMI to choose the test.
- 04Check the supply voltage, grounds and the data link first, because a weak battery or…
- 05Fix the cause, clear the codes with the tool and drive the truck to confirm the code…
How to read Volvo/Mack fault codes, in full
- Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
- Note the whole code as MID, then PID/SID/PPID/PSID, then FMI, and whether it is active or only logged with a count.
- Use the FMI to choose the test: 3 and 4 point to shorts, 5 to an open circuit, 0, 1 and 7 to a real condition on the machine.
- Check the supply voltage, grounds and the data link first, because a weak battery or a bad CAN link sets codes in several modules at once.
- Fix the cause, clear the codes with the tool (the cluster can no longer clear them on newer trucks) and drive the truck to confirm the code stays away.
How urgent is a Volvo/Mack code?
- Stop now25 codes
- Shut down and fix before working on. Running on risks damage or the machine locks out.
- Check soon146 codes
- The machine may derate or limit a function. Find the cause before the next shift.
- Information3 codes
- A reminder or status message. Nothing is failing yet.
Pick your system
Find the part of the machine, then the family your code belongs to.
- Code range
- The first and last code in the family, as the machine shows them.
- Codes
- How many codes the family holds; each is explained on its page.
- Severity mix
- The share of stop, check and info codes. The dot after it is the most urgent one in the family.
MID 128 engine ECU - sensors and levels26 codes
- Oil pressure, oil level and oil temperatureMID 128 PID 98 FMI 1 – MID 128 PID 175 FMI 1612 codes
- Coolant level and coolant temperature sensorsMID 128 PID 110 FMI 0 – MID 128 PID 111 FMI 59 codes
- Fan clutch controlMID 128 SID 33 FMI 3 – MID 128 SID 33 FMI 53 codes
- Coolant thermostat monitoringMID 128 PSID 109 FMI 7 – MID 128 PSID 109 FMI 122 codes
MID 128 engine ECU - air, turbo, EGR and brake32 codes
- Boost pressure and charge air temperatureMID 128 PID 102 FMI 2 – MID 128 PID 105 FMI 55 codes
- Variable geometry turbo actuatorMID 128 SID 27 FMI 2 – MID 128 SID 27 FMI 135 codes
- EGR valve controlMID 128 SID 146 FMI 3 – MID 128 SID 146 FMI 52 codes
- Turbo boost pressure controlMID 128 PSID 98 FMI 0 – MID 128 PSID 98 FMI 12 codes
- Engine compression brake outputMID 128 PPID 122 FMI 3 – MID 128 PPID 122 FMI 53 codes
- Exhaust gas temperature sensorMID 128 PID 173 FMI 0 – MID 128 PID 173 FMI 54 codes
- EGR flow and DPF filter pressure dropMID 128 PID 81 FMI 0 – MID 128 PID 411 FMI 15 codes
- EGR mass flowMID 128 PPID 35 FMI 0 – MID 128 PPID 35 FMI 12 codes
- EGR temperature sensorMID 128 PID 412 FMI 4 – MID 128 PID 412 FMI 52 codes
- Turbocharger speed signal missingMID 128 PID 103 FMI 9Check soon
- EGR cooler efficiency lowMID 128 SID 282 FMI 7Check soon
MID 128 engine ECU - fuel, injectors and timing30 codes
- Fuel delivery pressureMID 128 PID 94 FMI 3 – MID 128 PID 94 FMI 184 codes
- Water in fuel sensorMID 128 PID 97 FMI 0 – MID 128 PID 97 FMI 43 codes
- Crankcase pressureMID 128 PID 153 FMI 0 – MID 128 PID 153 FMI 74 codes
- Camshaft and crankshaft position sensorsMID 128 SID 21 FMI 2 – MID 128 SID 22 FMI 86 codes
- Injector circuits (cylinders 1-6)MID 128 SID 1 FMI 3 – MID 128 SID 6 FMI 510 codes
- Fuel actuator or valve controlMID 128 SID 18 FMI 3 – MID 128 SID 18 FMI 53 codes
MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)20 codes
- DPF soot levelMID 128 PPID 326 FMI 0 – MID 128 PPID 326 FMI 112 codes
- DPF regeneration temperatureMID 128 PSID 47 FMI 0 – MID 128 PSID 47 FMI 12 codes
- NOx sensors before and after the SCRMID 128 PPID 270 FMI 2 – MID 128 PPID 348 FMI 96 codes
- DEF dosing performanceMID 128 PSID 90 FMI 1 – MID 128 PSID 90 FMI 72 codes
- Hydrocarbon doser circuitMID 128 PPID 329 FMI 3 – MID 128 PPID 329 FMI 52 codes
- SCR system severe fault - operator inducementMID 128 PSID 46 FMI 0Stop now
- DEF pressure build-up failure - loss of primeMID 128 PSID 121 FMI 7Check soon
- DEF dosing pressure low - system leakMID 128 PPID 273 FMI 1Check soon
- Aftertreatment fuel pressure too lowMID 128 PPID 328 FMI 7Check soon
- DPF ash level too highMID 128 PPID 337 FMI 0Information
- DPF fuel pressure system faultMID 128 PPID 437 FMI 7Stop now
MID 128 engine ECU - module, data link and power14 codes
- J1939 data link 2 (aftertreatment)MID 128 PSID 229 FMI 2 – MID 128 PSID 229 FMI 92 codes
- Engine ECU battery voltageMID 128 PID 158 FMI 1 – MID 128 PID 158 FMI 32 codes
- Starter relay outputMID 128 SID 39 FMI 3 – MID 128 SID 39 FMI 52 codes
- Engine ECU program memoryMID 128 SID 240 FMI 2 – MID 128 SID 240 FMI 122 codes
- Vehicle identification number (VIN) missingMID 128 PSID 161 FMI 2Stop now
- Message from instrument cluster missingMID 128 PSID 201 FMI 9Check soon
- SAE J1939 data link (CAN 1) circuit faultMID 128 SID 231 FMI 2Check soon
- Sensor supply 1 (5 V) too highMID 128 SID 232 FMI 3Check soon
- Engine ECU calibration memory checksum errorMID 128 SID 253 FMI 2Stop now
- Engine ECU self-test failureMID 128 SID 254 FMI 12Stop now
MID 144 vehicle ECU25 codes
- Vehicle speed sensor signal and supplyMID 144 PID 84 FMI 2 – MID 144 PPID 265 FMI 45 codes
- Accelerator pedal positionMID 144 PID 91 FMI 3 – MID 144 PID 91 FMI 64 codes
- Pedal and engine brake sensor supplyMID 144 PPID 72 FMI 3 – MID 144 PPID 72 FMI 42 codes
- Idle validation switchesMID 144 PSID 2 FMI 7 – MID 144 SID 230 FMI 72 codes
- Air leakage - flow too highMID 144 PSID 25 FMI 14Check soon
- VECU number of resets - internal faultMID 144 PID 152 FMI 12Check soon
- Data link lost - engine control module (ECM)MID 144 PSID 200 FMI 9Check soon
- Data link lost - brake control module (ABS)MID 144 PSID 204 FMI 9Check soon
- Data link lost - transmission control module (TECU)MID 144 PSID 205 FMI 9Check soon
- VECU software reset from low supply voltageMID 144 PSID 230 FMI 4Check soon
- SAE J1939 data link intermittent or not acknowledgedMID 144 SID 231 FMI 2Check soon
- VECU program memory checksum errorMID 144 SID 240 FMI 2Stop now
- Cruise control set switch - SET+ and SET- at the same timeMID 144 SID 243 FMI 7Check soon
- SAE J1587 data link faulty messagesMID 144 SID 250 FMI 2Check soon
- VECU calibration memory (EEPROM) checksum errorMID 144 SID 253 FMI 2Check soon
- Air dryer regeneration air flow too highMID 144 PPID 312 FMI 0Check soon
MID 130 transmission ECU23 codes
- Clutch position sensorMID 130 PID 33 FMI 2 – MID 130 PID 33 FMI 134 codes
- Transmission air pressureMID 130 PID 37 FMI 0 – MID 130 PID 37 FMI 12 codes
- Transmission oil temperatureMID 130 PID 177 FMI 0 – MID 130 PID 177 FMI 42 codes
- Clutch operationMID 130 PSID 27 FMI 0 – MID 130 PSID 27 FMI 144 codes
- Clutch overheat protectionMID 130 PPID 50 FMI 0 – MID 130 PPID 50 FMI 112 codes
- Quick engagement PWM valveMID 130 PSID 1 FMI 3 – MID 130 PSID 1 FMI 52 codes
- Gear engagementMID 130 PSID 25 FMI 11 – MID 130 PSID 25 FMI 122 codes
- Counter shaft brake valve shorted high - brake appliedMID 130 PSID 22 FMI 3Stop now
- Clutch wear above service limitMID 130 PID 36 FMI 0Information
- Transmission control unit battery voltage lowMID 130 PID 158 FMI 1Check soon
- Lost data link to engine control module (ECM)MID 130 PSID 200 FMI 9Check soon
- Lost data link to vehicle ECUMID 130 PSID 201 FMI 9Check soon
MID 136 brake ECU (ABS)1 code
MID 140 instrument cluster3 codes
Most searched Volvo/Mack codes
- MID 128 SID 1 FMI 3Injector cylinder 1 circuit shorted high
- MID 128 SID 1 FMI 5Injector cylinder 1 circuit open or shorted to ground
- MID 128 SID 2 FMI 5Injector cylinder 2 circuit open or shorted
- MID 128 SID 21 FMI 2Camshaft position sensor phase error
- MID 128 SID 22 FMI 2Crankshaft position sensor intermittent or weak signal
- MID 128 SID 22 FMI 3Crankshaft position sensor signal missing
- MID 128 SID 27 FMI 2Variable geometry turbo actuator - no valid command received
- MID 128 SID 33 FMI 3Fan clutch output shorted high - fan runs full speed
- MID 128 PSID 46 FMI 0SCR system severe fault - operator inducement
- MID 128 PSID 47 FMI 0Unable to reach regeneration temperature
- MID 128 PID 81 FMI 0DPF differential pressure critically high
- MID 128 PSID 90 FMI 1DEF dosing too low - NOx limits exceeded, poor DEF quality
- MID 128 PID 94 FMI 7Fuel delivery pressure dropping, supply not responding
- MID 128 PID 97 FMI 0Water in fuel detected
- MID 128 PSID 98 FMI 0Turbocharger boost pressure too high
- MID 128 PID 98 FMI 1Engine oil level critically low
- MID 128 PSID 98 FMI 1Turbocharger boost pressure too low
- MID 128 PID 100 FMI 1Engine oil pressure critically low
- MID 128 PID 100 FMI 3Engine oil pressure sensor circuit shorted or ground open
- MID 128 PID 100 FMI 5Engine oil pressure sensor circuit open or shorted to ground
- MID 128 PID 102 FMI 3Intake manifold (boost) pressure sensor signal high
- MID 128 PSID 109 FMI 7Coolant thermostat stuck closed
- MID 128 PSID 109 FMI 12Coolant thermostat leaking or stuck open
- MID 128 PID 110 FMI 0Engine coolant temperature critically high
- MID 128 PID 110 FMI 4Engine coolant temperature sensor signal low or shorted to ground
- MID 128 PID 111 FMI 1Engine coolant level critically low
- MID 128 PSID 121 FMI 7DEF pressure build-up failure - loss of prime
- MID 128 PPID 122 FMI 3Engine compression brake output shorted high
- MID 128 SID 146 FMI 3EGR valve control shorted high or stuck
- MID 128 PID 153 FMI 0Crankcase pressure critically high
- MID 128 PID 158 FMI 1ECM battery voltage too low
- MID 128 PSID 229 FMI 9SAE J1939 data link 2 - lost communication with aftertreatment module
- MID 128 SID 231 FMI 2SAE J1939 data link (CAN 1) circuit fault
- MID 128 SID 232 FMI 3Sensor supply 1 (5 V) too high
- MID 128 PPID 270 FMI 9Outlet NOx sensor signal missing
- MID 128 PPID 326 FMI 0DPF soot level moderately high
- MID 128 PPID 326 FMI 11DPF soot level critically high
- MID 128 PPID 337 FMI 0DPF ash level too high
- MID 128 PPID 348 FMI 9Inlet NOx sensor signal missing
- MID 130 PSID 27 FMI 12Clutch slipping
- MID 130 PSID 27 FMI 14Clutch cannot disengage - engine shut down
- MID 130 PID 33 FMI 2Clutch position sensor signals disagree
- MID 130 PID 36 FMI 0Clutch wear above service limit
- MID 130 PID 37 FMI 1Transmission air pressure too low
- MID 130 PID 177 FMI 0Transmission oil temperature high
- MID 130 PSID 200 FMI 9Lost data link to engine control module (ECM)
- MID 136 SID 66 FMI 7ABS - mechanical system not responding (can set with no fault)
- MID 140 PSID 210 FMI 12Instrument cluster watchdog timeout (logged on DTC readout only)
- MID 144 PID 84 FMI 2Vehicle speed signal incorrect or intermittent
- MID 144 PID 84 FMI 5Vehicle speed sensor open circuit or shorted to ground
- MID 144 PID 91 FMI 3Accelerator pedal position signal high
- MID 144 PID 91 FMI 4Accelerator pedal position signal low
- MID 144 PSID 200 FMI 9Data link lost - engine control module (ECM)
- MID 144 SID 231 FMI 2SAE J1939 data link intermittent or not acknowledged
Quick answers
How do I read Volvo/Mack fault codes?
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine. Note the whole code as MID, then PID/SID/PPID/PSID, then FMI, and whether it is active or only logged with a count.
Which Volvo/Mack codes mean stop now?
25 of the 174 Volvo/Mack codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example MID 128 SID 22 FMI 3, MID 128 PSID 46 FMI 0, MID 128 PID 81 FMI 0, MID 128 PSID 90 FMI 1. 146 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.
What should I check first on a Volvo/Mack code?
Most Volvo/Mack codes here (36 of 174) read as real condition: the sensor reading is valid but outside the allowed range - the problem may be real. First test, as general workshop practice: check the real value with a separate gauge or thermometer before blaming the sensor.
Which Volvo/Mack codes are looked up most?
MID 128 SID 1 FMI 3 (injector cylinder 1 circuit shorted high), MID 128 SID 1 FMI 5 (injector cylinder 1 circuit open or shorted to ground), MID 128 SID 2 FMI 5 (injector cylinder 2 circuit open or shorted), MID 128 SID 21 FMI 2 (camshaft position sensor phase error), MID 128 SID 22 FMI 2 (crankshaft position sensor intermittent or weak signal). Each page gives the meaning, the likely causes and the checks.
Sources
Every code was read from these documents and written in our own words.
- Mack Group 28 Engine Control Module (ECM) Diagnostic Trouble Code Guide, 2010 Emissions CHU/CXU/GU/TD, PV776-89047073
- Mack Group 36 Vehicle Electronic Control Unit (MID 144) Diagnostic Trouble Code Guide, PV776-88951780
- Mack Service Bulletin 430 17 01, MID 130 Diagnostic Trouble Codes mDRIVE Transmission, PV776-89138344
- Volvo Trucks Field Service Bulletin FSB 513-001: Brake ECU Reprogramming (MID 136), April 2015
- Mack Field Service Bulletin FSB 381-049: Instrument Cluster Reprogramming (MID 140), May 2013
- Volvo/Mack Solution K53357197: MID 140 PSID 210 FMI 12, Model Year 2018
Other makers
Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.
Post a request