Volvo/Mack · MID 144 vehicle ECU
Volvo/Mack Fault Code MID 144 PSID 200 FMI 9
Data link lost - engine control module (ECM)
What does Volvo/Mack code MID 144 PSID 200 FMI 9 mean?
The VECU did not receive the expected messages from the engine control module (ECM) on the J1939 CAN 1 link. The guide also lists a configuration mismatch between the VECU and the ECM as a cause. Urgency: check soon - the machine may derate or limit a function. Check first: read the engine ECM in the scan tool; no response means power, ground or the CAN wires to it.
- MID 144
- Which control unit reports it
- PSID 200
- Maker component at fault
- FMI 9
- Abnormal update rate
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read the engine ECM in the scan tool; no response means power, ground or the CAN wires to it
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- CAN 1 link between the VECU and the engine ECM down or shorted
- Configuration mismatch between the VECU and the engine control module after a software or parameter change
- Engine ECM not powered or held in reset
How it failed
You'll notice: Yellow lamp lit and engine-dependent functions such as PTO, cruise and engine brake may drop out while the VECU waits for the engine messages.
Lost messageRead from FMI 9: abnormal update rate
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Other Volvo/Mack codes: MID 144 vehicle ECU
- MID 144 PSID 25 FMI 14Air leakage - flow too high
- MID 144 PPID 72 FMI 3Pedal and engine brake sensor supply too high
- MID 144 PPID 72 FMI 4Pedal and engine brake sensor supply too low
- MID 144 PID 84 FMI 2Vehicle speed signal incorrect or intermittent
- MID 144 PID 84 FMI 5Vehicle speed sensor open circuit or shorted to ground
- MID 144 PID 84 FMI 6Vehicle speed sensor current high or shorted across sensor
- MID 144 PID 91 FMI 3Accelerator pedal position signal high
- MID 144 PID 91 FMI 4Accelerator pedal position signal low
Related on Equipments Finder
Source
This source lists MID 144 PSID 200 FMI 9 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack and Volvo trucks with the MID 144 vehicle ECU (VECU), built from 2007; guide written for Mack, same VECU family as Volvo VN/VNL.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
