Volvo/Mack · MID 144 vehicle ECU
Volvo/Mack Fault Code MID 144 PID 91 FMI 3
Accelerator pedal position signal high
What does Volvo/Mack code MID 144 PID 91 FMI 3 mean?
The pedal position sensor signal is above about 4.3 V, which the VECU treats as an abnormally high voltage or a short to a higher voltage. The pedal value cannot be trusted. Urgency: check soon - the machine may derate or limit a function. Check first: read the pedal percentage with the pedal released; it should sit at zero.
- MID 144
- Which control unit reports it
- PID 91
- Parameter at fault
- FMI 3
- Voltage above normal or shorted high
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read the pedal percentage with the pedal released; it should sit at zero
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Accelerator pedal position harness shorted high
- Faulty accelerator pedal position sensor
- Short to battery voltage in the pedal connector
How it failed
You'll notice: Yellow check lamp comes on and the engine will not deliver the fuel the pedal asks for, so you get limp-home response.
Shorted highRead from FMI 3: voltage above normal or shorted high
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Accelerator pedal position
- MID 144 PID 91 FMI 3Accelerator pedal position signal highShorted highCheck soon
- MID 144 PID 91 FMI 4Accelerator pedal position signal lowShorted lowCheck soon
- MID 144 PID 91 FMI 5Accelerator pedal position low compared with idle validation switchesOpen circuitCheck soon
- MID 144 PID 91 FMI 6Accelerator pedal position high compared with idle validation switches / loss of sensor groundShorted lowCheck soon
Other Volvo/Mack codes: MID 144 vehicle ECU
- MID 144 PSID 2 FMI 7Idle validation switch 2 reads wrong
- MID 144 PSID 25 FMI 14Air leakage - flow too high
- MID 144 PPID 72 FMI 3Pedal and engine brake sensor supply too high
- MID 144 PPID 72 FMI 4Pedal and engine brake sensor supply too low
- MID 144 PID 84 FMI 2Vehicle speed signal incorrect or intermittent
- MID 144 PID 84 FMI 5Vehicle speed sensor open circuit or shorted to ground
Related on Equipments Finder
Source
This source lists MID 144 PID 91 FMI 3 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack and Volvo trucks with the MID 144 vehicle ECU (VECU), built from 2007; guide written for Mack, same VECU family as Volvo VN/VNL.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
