Volvo/Mack · MID 144 vehicle ECU
Volvo/Mack Fault Code MID 144 PID 84 FMI 5
Vehicle speed sensor open circuit or shorted to ground
What does Volvo/Mack code MID 144 PID 84 FMI 5 mean?
The VECU sees low current on the vehicle speed sensor circuit, which means an open circuit or a sensor shorted to ground. No valid pulse train comes from the sensor. Urgency: check soon - the machine may derate or limit a function. Check first: read vehicle speed in the scan tool while driving; zero or erratic speed points at the circuit.
- MID 144
- Which control unit reports it
- PID 84
- Parameter at fault
- FMI 5
- Current below normal or open circuit
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read vehicle speed in the scan tool while driving; zero or erratic speed points at the circuit
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- VSS harness or connector open
- VSS sensor open or shorted to ground
- Damaged wire where the harness is clamped near the transmission
How it failed
You'll notice: The speedometer shows the wrong road speed in the cluster, and anything that uses speed (cruise, speed limit) may behave oddly.
Open circuitRead from FMI 5: current below normal or open circuit
No current flows, or the signal floats - a wire, pin or coil is broken.
- Meter test
- Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
- Good result
- Near 0 Ω on each wire. The part reads its listed resistance, not OL.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Vehicle speed sensor signal and supply
- MID 144 PID 84 FMI 2Vehicle speed signal incorrect or intermittentErratic or implausibleCheck soon
- MID 144 PID 84 FMI 5Vehicle speed sensor open circuit or shorted to groundOpen circuitCheck soon
- MID 144 PID 84 FMI 6Vehicle speed sensor current high or shorted across sensorShorted lowCheck soon
- MID 144 PPID 265 FMI 3Vehicle speed sensor supply too highShorted highCheck soon
- MID 144 PPID 265 FMI 4Vehicle speed sensor supply too lowShorted lowCheck soon
Other Volvo/Mack codes: MID 144 vehicle ECU
- MID 144 PSID 2 FMI 7Idle validation switch 2 reads wrong
- MID 144 PSID 25 FMI 14Air leakage - flow too high
- MID 144 PPID 72 FMI 3Pedal and engine brake sensor supply too high
- MID 144 PPID 72 FMI 4Pedal and engine brake sensor supply too low
- MID 144 PID 91 FMI 3Accelerator pedal position signal high
- MID 144 PID 91 FMI 4Accelerator pedal position signal low
Related on Equipments Finder
Source
This source lists MID 144 PID 84 FMI 5 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack and Volvo trucks with the MID 144 vehicle ECU (VECU), built from 2007; guide written for Mack, same VECU family as Volvo VN/VNL.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
