Volvo/Mack · MID 144 vehicle ECU
Volvo/Mack Fault Code MID 144 PID 84 FMI 2
Vehicle speed signal incorrect or intermittent
What does Volvo/Mack code MID 144 PID 84 FMI 2 mean?
The vehicle speed signal from the speed sensor and the one from the ABS differ too much, or one of them is intermittent. The VECU cannot decide which road speed is right. Urgency: check soon - the machine may derate or limit a function. Check first: compare the speedometer, the ABS wheel speed and the speed in the scan tool on a test drive.
- MID 144
- Which control unit reports it
- PID 84
- Parameter at fault
- FMI 2
- Erratic or incorrect data
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Compare the speedometer, the ABS wheel speed and the speed in the scan tool on a test drive
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Vehicle speed sensor (VSS) harness damaged or rubbing at the transmission
- Faulty VSS at the transmission output
- Wrong K-factor (MG and MH parameters in the VECU) after a tyre, axle or transmission change
- ABS speed message missing or inconsistent
How it failed
You'll notice: The speedometer and tachograph drop out or jump, and the cluster may show the wrong road speed.
Erratic or implausibleRead from FMI 2: erratic or incorrect data
The reading jumps, drifts or disagrees with the sensors around it.
- Meter test
- Watch the live value on the service tool while you flex the harness and tap the connector.
- Good result
- A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Vehicle speed sensor signal and supply
- MID 144 PID 84 FMI 2Vehicle speed signal incorrect or intermittentErratic or implausibleCheck soon
- MID 144 PID 84 FMI 5Vehicle speed sensor open circuit or shorted to groundOpen circuitCheck soon
- MID 144 PID 84 FMI 6Vehicle speed sensor current high or shorted across sensorShorted lowCheck soon
- MID 144 PPID 265 FMI 3Vehicle speed sensor supply too highShorted highCheck soon
- MID 144 PPID 265 FMI 4Vehicle speed sensor supply too lowShorted lowCheck soon
Other Volvo/Mack codes: MID 144 vehicle ECU
- MID 144 PSID 2 FMI 7Idle validation switch 2 reads wrong
- MID 144 PSID 25 FMI 14Air leakage - flow too high
- MID 144 PPID 72 FMI 3Pedal and engine brake sensor supply too high
- MID 144 PPID 72 FMI 4Pedal and engine brake sensor supply too low
- MID 144 PID 91 FMI 3Accelerator pedal position signal high
- MID 144 PID 91 FMI 4Accelerator pedal position signal low
Related on Equipments Finder
Source
This source lists MID 144 PID 84 FMI 2 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack and Volvo trucks with the MID 144 vehicle ECU (VECU), built from 2007; guide written for Mack, same VECU family as Volvo VN/VNL.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
