Volvo/Mack · MID 144 vehicle ECU
Volvo/Mack Pedal and engine brake sensor supply fault codes
The vehicle ECU supplies voltage to the pedal and engine brake sensors. These codes mean that supply is outside its range.
Where to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
What do these codes mean?
Volvo/Mack codes MID 144 PPID 72 FMI 3 and MID 144 PPID 72 FMI 4 are all about the pedal and engine brake sensor supply. None needs an immediate stop. Start with this check: unplug the pedal and engine brake sensors one at a time and watch whether the supply recovers.
How urgent are they?
None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.
- Check soon2
What should I check first?
Unplug the pedal and engine brake sensors one at a time and watch whether the supply recovers
Shared checksStop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Volvo/Mack MID 144 PPID 72 FMI 3Pedal and engine brake sensor supply too high
The 5 V supply that feeds the accelerator pedal and engine brake sensors reads above 5.7 V. A short to a higher voltage in the pedal harness or a faulty pedal sensor is the cause.· Shorted highShorted highCheck soonCauses
- Accelerator pedal position sensor harness shorted high
- Faulty accelerator pedal position sensor
- Engine brake switch circuit sharing the supply
Checks
- 1Measure the supply voltage at the pedal connector with the key on
- 2Unplug the engine brake switch and pedal sensor one at a time to see which restores a normal supply
- 3Check the harness for a short to battery positive
- 4Replace the faulty sensor
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Volvo/Mack MID 144 PPID 72 FMI 4Pedal and engine brake sensor supply too low
The 5 V supply to the accelerator pedal and engine brake sensors reads below 4.7 V. A short to ground in the pedal harness or a faulty sensor pulls it down.· Shorted lowShorted lowCheck soonCauses
- Accelerator pedal position sensor harness shorted low
- Faulty accelerator pedal position sensor
- Water in the pedal connector
Checks
- 1Measure the supply voltage at the pedal connector with the key on
- 2Unplug each sensor on this supply in turn to see which one pulls the voltage down
- 3Check the supply wire for a short to ground for damage, corrosion or looseness
- 4Inspect the connector for water and corrosion
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Shared checks
Checks, in order
- 1Unplug the pedal and engine brake sensors one at a time and watch whether the supply recovers
- 2Measure the 5 V sensor supply at the vehicle ECU pin and at the sensor plug to find the loss
- 3Check the harness between the ECU and the sensors for a short to ground or to battery voltage
- 4Check the sensor connectors for corrosion, water and pins that no longer grip
Causes
- Short in the supply wire
- Sensor failed and pulling the supply down
- ECU output fault
When to stop
You'll notice: The pedal or engine brake may not work and a check lamp comes on.
Brake and steering faults are a safety issue on site. Chock the machine and keep it parked until the fault is found and the brakes are tested.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
