EF Logo

Volvo/Mack · MID 130 transmission ECU

Volvo/Mack Transmission oil temperature fault codes

The transmission oil temperature sensor reports the oil temperature to the transmission ECU for protection.

FaultStopMID 130PID 177FMI 0Volvo/Mack · Transmission oil temperature
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 130 PID 177 FMI 0 and MID 130 PID 177 FMI 4 are all about the transmission oil temperature. 1 needs an immediate stop. Start with this check: check the transmission oil level and condition, since low or burnt oil raises the temperature quickly.

How urgent are they?

1 of 2 codes here means stop now; the other 1 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon1

What should I check first?

Check the transmission oil level and condition, since low or burnt oil raises the temperature quickly

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 130 PID 177 FMI 0Transmission oil temperature high

    Transmission oil is overheating.· Real condition
    Stop now

    Causes

    • Transmission oil cooler blocked or low airflow
    • Low or overfilled transmission oil level
    • Heavy load or sustained climbing in too high a gear
    • Engine coolant system overheating

    Checks

    1. 1Stop and let the transmission cool if the red lamp is on
    2. 2Check transmission oil level and condition for damage, corrosion or looseness
    3. 3Check the oil cooler and its lines for blockage
    4. 4Check the engine cooling system and the fan for damage, corrosion or looseness
    5. 5Check the oil temperature sensor reading against a thermometer
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 130 PID 177 FMI 4Transmission oil temperature sensor low or shorted

    The transmission oil temperature sensor signal is below its normal range, so the control unit sees a sensor fault, not real temperature.· Shorted low
    Check soon

    Causes

    • Sensor shorted to ground
    • Damaged wiring
    • Failed sensor

    Checks

    1. 1Check the sensor connector for oil and corrosion
    2. 2Test the sensor circuit for a short to ground
    3. 3Check the sensor resistance against the manual
    4. 4Replace the sensor
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Check the transmission oil level and condition, since low or burnt oil raises the temperature quickly
  2. 2Check the transmission oil cooler and its lines for blockage and for airflow that is blocked by debris
  3. 3Check the sensor connector for oil, corrosion and loose pins before replacing the sensor
  4. 4Compare the sensor reading with a measured value

Causes

  • Real overheating from heavy load or low oil
  • Sensor failed
  • Wiring fault

When to stop

You'll notice: A warning lamp comes on and the truck may limit performance.

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.