EF Logo

Volvo/Mack · MID 130 transmission ECU

Volvo/Mack Transmission air pressure fault codes

The mDRIVE transmission uses compressed air for the clutch and shifting, and the transmission ECU monitors that pressure.

FaultCheckMID 130PID 37FMI 1Volvo/Mack · Transmission air pressure
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 130 PID 37 FMI 0 and MID 130 PID 37 FMI 1 are all about the transmission air pressure. Most are real condition faults; none needs an immediate stop. Start with this check: check the air system pressure at the gauge.

How urgent are they?

None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.

  • Check soon2

What should I check first?

Check the air system pressure at the gauge

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 130 PID 37 FMI 0Transmission air pressure too high

    The air pressure measured at the transmission is above 145 psi (10.0 bar), higher than the control unit expects.· Real condition
    Check soon

    Causes

    • Air governor or pressure regulator fault
    • Air compressor unloader fault
    • Air pressure sensor reading wrongly

    Checks

    1. 1Check system air pressure with a test gauge for damage, corrosion or looseness
    2. 2Check the governor cut-out pressure
    3. 3Check the air pressure sensor reading against the gauge
    4. 4Repair or replace the part at fault
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 130 PID 37 FMI 1Transmission air pressure too low

    The air pressure supplied to the transmission is below 72.5 psi (5.0 bar).· Real condition
    Check soon

    Causes

    • Low system air pressure from a leak
    • Air dryer or governor fault
    • Restricted air supply line to the transmission

    Checks

    1. 1Read air pressure in the scan tool and compare it with the cluster gauge
    2. 2Check the air system for leaks and listen at the transmission valve block
    3. 3Check the air dryer, governor and supply line to the transmission
    4. 4Check that the pressure sensor reading matches the real pressure
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Check the air system pressure at the gauge
  2. 2Inspect the air lines and fittings of the transmission for leaks and chafed or kinked hoses
  3. 3Check the pressure sensor reading against a gauge on the same line to see whether it is accurate
  4. 4Check the pressure regulator for a stuck valve or contamination that holds the pressure too low or high

Causes

  • Air leak in the transmission lines
  • Pressure regulator fault
  • Low system air pressure

Most codes here: real condition (2 of 2)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: Shifting is slow or disabled, the transmission warning comes on, and the truck may not start off.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.