EF Logo

Volvo/Mack · MID 128 engine ECU - sensors and levels

Volvo/Mack Fault Code MID 128 PSID 109 FMI 12

Coolant thermostat leaking or stuck open

What does Volvo/Mack code MID 128 PSID 109 FMI 12 mean?

The coolant thermostat is leaking or stuck open, so the engine takes too long to warm up and the ECM logs a fault for it. Urgency: check soon - the machine may derate or limit a function. Check first: watch the coolant warm-up time in the scan tool on a cold start and compare it with a known good truck.

FaultCheckMID 128PSID 109FMI 12Volvo/Mack · MID 128 engine ECU - sensors and levels
MID 128
Which control unit reports it
PSID 109
Maker component at fault
FMI 12
Bad intelligent device or component

Can I keep running with it?

Check soon

The machine may derate or limit a function. Find the cause before the next shift.

What should I check first?

Watch the coolant warm-up time in the scan tool on a cold start and compare it with a known good truck

Then 3 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

Checks

0 of 4 done

Causes

  • Thermostat stuck open
  • Coolant temperature sensor misreading
  • Fan running too much

How it failed

You'll notice: Longer engine warm-up, poor heat in the cab and a lit MIL while the thermostat stays open.

Part or controllerRead from FMI 12: bad intelligent device or component

The controller reports a part, module or its software as faulty or not responding.

ControllerPartSupplySignalGround?
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.
Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good result
Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

When to stop

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Same part, other failures: Coolant thermostat monitoring

1 other code on this part is also part or controller (MID 128 PSID 109 FMI 7). When they show together, start at the wiring and connector they share.

All 2 Coolant thermostat monitoring codes on one page

Source

Mack Group 28 Engine Control Module (ECM) Diagnostic Trouble Code Guide, 2010 Emissions CHU/CXU/GU/TD, PV776-89047073 (MID 128 PID/SID tables)

This source lists MID 128 PSID 109 FMI 12 and its meaning. The guidance on this page is general, not taken from it.

The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.