EF Logo

Volvo/Mack · MID 128 engine ECU - sensors and levels

Volvo/Mack Oil pressure, oil level and oil temperature fault codes

Three engine oil measurements reach the engine ECU on MID 128. The oil pressure sensor sits in the main oil gallery on the block and feeds the gauge and engine protection.

More about these parts

The oil level sensor in the oil pan reports how much oil is in the sump. The oil temperature sensor in the oil circuit gives the ECU the oil temperature for viscosity compensation. Each code names which of the three is at fault and whether the reading is real or the circuit is broken.

FaultStopMID 128PID 98FMI 1Volvo/Mack · Oil pressure, oil level and oil temperature
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PID 98 FMI 1 to MID 128 PID 175 FMI 16 are all about the oil pressure, oil level and oil temperature. The most common failure type is real condition (4 of 12); 3 need an immediate stop. Start with this check: check the dipstick on level ground with the engine stopped before anything else; add oil only after finding where it went.

How urgent are they?

3 of 12 codes here mean stop now; the other 9 can wait until the shift ends, but find the cause before the next one.

  • Stop now3
  • Check soon9

What should I check first?

Check the dipstick on level ground with the engine stopped before anything else; add oil only after finding where it went

Shared checks

12 of 12

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PID 98 FMI 1Engine oil level critically low

    The oil level sensor in the sump reports oil critically below the allowed range.· Real condition
    Stop now

    Causes

    • Oil actually low from consumption or a leak since the last service
    • Oil level not topped up after an oil change or turbo service
    • Overfill followed by loss on a long climb, leaving the sump reading low

    Checks

    1. 1Park level, wait a few minutes and read the dipstick; the dipstick is the reference, not the cluster
    2. 2Top up with the correct grade only after looking for leaks around the pan, cooler and turbo feed
    3. 3Compare the live level reading in the scan tool with the dipstick after topping up
    4. 4If the level is correct on the dipstick but the code stays, move to the level sensor and its harness
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PID 98 FMI 4Engine oil level sensor shorted to ground

    The oil level sensor circuit reads low, which Mack ties to a short on the negative side of the circuit.· Shorted low
    Check soon

    Causes

    • Oil level (EOL) sensor failed with an internal short
    • Sensor harness rubbed through to ground near the oil pan
    • Oil-soaked connector bridging two terminals

    Checks

    1. 1Read the live oil level value; no value or a fixed value confirms the sensor is not measuring
    2. 2Unplug the sensor and check the harness pins for a short to ground with the key off
    3. 3Look at the connector for oil inside the plug, clean it and dry it
    4. 4Replace the sensor only after the wiring tests clean, then verify the level reading against the dipstick
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Volvo/Mack MID 128 PID 98 FMI 5Engine oil level sensor circuit open

    The ECM sees an open circuit on the oil level sensor, either on the positive or negative side, or a short on the positive side.· Open circuit
    Check soon

    Causes

    • Open positive wire to the oil level sensor
    • Open ground (negative) wire from the sensor to the ECM
    • Sensor connector pin backed out after an oil pan or starter job
    • Oil level sensor failed open

    Checks

    1. 1Check the live oil level value; no reading points at an open circuit
    2. 2Test continuity of both sensor wires between the connector and the ECM with the key off
    3. 3Check the sensor connector for pushed-back pins and oil contamination
    4. 4Substitute a known-good sensor if both wires test good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 PID 100 FMI 1Engine oil pressure critically low

    The engine ECU measured oil pressure far below the range it expects for the current speed and load, and the reading is real, not a sensor fault.· Real condition
    Stop now

    Causes

    • Oil level far down from a leak at the filter housing, oil cooler, turbo oil lines or a rear main seal
    • Oil pump worn or broken so it cannot build pressure at idle
    • Oil galleries or filter restricted by sludge and neglected oil changes
    • Oil diluted with fuel or too thin for the operating temperature, so pressure collapses when hot

    Checks

    1. 1Stop the engine and check the dipstick on level ground before anything else; add oil only after finding where it went
    2. 2Fit a mechanical test gauge at the oil gallery port and compare it with the cluster reading at idle and at high idle
    3. 3Look under the engine and around the oil cooler and turbo feed for fresh oil, and smell the oil for diesel
    4. 4Check that the oil filter is the correct part and not collapsed or blocked, and that the filter bypass is not stuck
    5. 5If the test gauge reads normal but the ECU still sets the code, move to the sensor and its wiring
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PID 100 FMI 3Engine oil pressure sensor circuit shorted or ground open

    The oil pressure sensor signal is outside its valid electrical band.· Shorted high
    Check soon

    Causes

    • Measuring (signal) wire touching battery positive or the 5 V supply somewhere along the engine harness
    • Open sensor ground wire so the signal floats up to the supply level
    • Engine oil pressure sensor failed internally after oil or heat damage
    • Corroded pins in the sensor connector on the block

    Checks

    1. 1Compare the real pressure with a mechanical gauge first so you know the engine itself is not the problem
    2. 2With the key on, unplug the sensor and measure the 5 V supply and ground at the harness plug
    3. 3Check the signal wire for a short to battery or 5 V with the sensor unplugged and the key off
    4. 4Test the ground wire resistance back to the ECM; a high value points at a damaged return
    5. 5Inspect the connector for green corrosion and oil wicking up the harness, then replace the sensor only if the circuit is clean
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 PID 100 FMI 5Engine oil pressure sensor circuit open or shorted to ground

    The ECM sees the oil pressure sensor circuit as open or pulled to ground.· Open circuit
    Check soon

    Causes

    • Open 5 V supply wire to the oil pressure sensor, often a broken strand near the connector
    • Measuring wire chafed to ground against the block or a bracket
    • Measuring wire broken or pin pushed back in the connector
    • Engine oil pressure sensor failed open

    Checks

    1. 1Read oil pressure live in the scan tool; a value stuck at zero with the engine running confirms the circuit fault
    2. 2Unplug the sensor and check for 5 V between the supply and ground pins at the harness side
    3. 3If 5 V is missing, trace the supply wire back toward the ECM and look for a break at a splice or the firewall connector
    4. 4Measure the signal wire to ground with the key off; it should not be a dead short
    5. 5Wiggle the harness along the block while watching the live value to catch an intermittent break
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 PID 100 FMI 13Engine oil pressure sensor out of calibration

    The engine oil pressure sensor is giving a value the ECM judges invalid.· Part or controller
    Check soon

    Causes

    • Engine oil pressure sensor drifted or contaminated and no longer reads true
    • Poor terminal contact adding resistance in the signal path
    • Sensor port partly blocked with sludge so pressure does not reach the diaphragm

    Checks

    1. 1Compare the scan tool value with a mechanical gauge at idle; a difference means the sensor is wrong
    2. 2Check the sensor is the correct part number for the engine and is fully seated
    3. 3Clean and inspect the connector terminals and reseat them firmly
    4. 4Replace the sensor and recheck the live value against the gauge before clearing the code
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Volvo/Mack MID 128 PID 175 FMI 0Engine oil temperature critically high

    Oil temperature has passed the critical limit.· Real condition
    Stop now

    Causes

    • Engine cooling fan or coolant system not removing heat
    • Oil cooler clogged internally or externally
    • Oil thermostat stuck so oil bypasses the cooler
    • Extreme driving conditions with heavy load at low speed

    Checks

    1. 1Compare oil temperature with coolant temperature; a large gap points at the oil cooler or thermostat
    2. 2Check the fan engages and the radiator is clean
    3. 3Check oil level and condition since a low or burnt oil raises temperature
    4. 4Inspect the oil cooler for restriction by checking flow or pressure drop across it
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PID 175 FMI 2Engine oil temperature signal erratic

    The oil temperature reading is jumping or showing an implausible value.· Erratic or implausible
    Check soon

    Causes

    • Engine oil temperature (EOT) sensor failing intermittently
    • Chafed wire or poor terminal contact in the sensor harness
    • Sensor connector filled with oil, giving a wandering signal

    Checks

    1. 1Watch the oil temperature trend while warming up; it should climb steadily, not step or jump
    2. 2Wiggle the harness and connector near the sensor and look for jumps in the live value
    3. 3Compare oil temperature with coolant temperature on a cold engine after a long soak
    4. 4Replace the sensor if the readings stay erratic with a good harness
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Volvo/Mack MID 128 PID 175 FMI 4Engine oil temperature sensor shorted to ground

    The oil temperature signal reads low and Mack ties it to a short on the measuring line.· Shorted low
    Check soon

    Causes

    • Oil temperature sensor failed shorted
    • Measuring wire shorted to ground in the engine harness
    • Oil-soaked connector bridging the signal to ground

    Checks

    1. 1Read the live oil temperature; an impossibly low value on a running engine confirms it
    2. 2Unplug the sensor and test the signal wire to ground with the key off
    3. 3Inspect the harness along the block for rub-through
    4. 4Replace the sensor if the harness is clean and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Volvo/Mack MID 128 PID 175 FMI 5Engine oil temperature sensor circuit open

    The oil temperature circuit is open, or shorted to positive on the measuring line.· Open circuit
    Check soon

    Causes

    • Open measuring or ground wire
    • Connector unplugged or pin backed out
    • Sensor failed open

    Checks

    1. 1Read the live value; a value stuck at its maximum points at an open circuit
    2. 2Check continuity of both sensor wires between the connector and the ECM
    3. 3Reseat the connector and inspect the terminals for push-back
    4. 4Replace the sensor if the wiring is good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 PID 175 FMI 16Engine oil temperature moderately high

    Oil temperature is above its upper warning level but not yet critical.· Real condition
    Check soon

    Causes

    • Extreme driving conditions with sustained load
    • Fan not working properly or radiator airflow restricted
    • Oil thermostat sticking
    • Clogged oil cooler

    Checks

    1. 1Log oil and coolant temperatures during a loaded drive and see which one climbs first
    2. 2Check the cooling fan control and the radiator face for blockage
    3. 3Check oil level and oil age, because low or burnt oil runs hotter
    4. 4Test the oil thermostat operation if the oil runs hot while coolant stays normal
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Check the dipstick on level ground with the engine stopped before anything else; add oil only after finding where it went
  2. 2For a pressure code, fit a mechanical gauge at the oil gallery port and compare it with the cluster reading at idle and high idle
  3. 3For a level code, compare the cluster level with the dipstick after the engine has stood for several minutes and look at the pan sensor connector for oil wicking
  4. 4For a temperature code, check the oil cooler and its coolant side for blockage and compare the oil value with coolant temperature on a cold engine
  5. 5Unplug the affected sensor, inspect the pins for oil or green corrosion and measure supply, ground and signal wires for a short or an open
  6. 6Read the codes again after the repair and confirm they do not return on a test drive

Causes

  • Oil lost to a leak at the filter housing, oil cooler, turbo oil lines or rear main seal, which lowers both level and pressure
  • Worn oil pump, blocked filter or fuel-thinned oil that cannot hold pressure
  • Blocked oil cooler or heavy load that overheats the oil
  • Failed sensor or corroded connector on the pressure, level or temperature sensor

Most common here: real condition (4 of 12)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The oil pressure gauge reads low or zero, the cluster shows a low oil level warning or no level at all, or the oil temperature reads wrongly.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.