EF Logo

Volvo/Mack · MID 128 engine ECU - sensors and levels

Volvo/Mack Coolant thermostat monitoring fault codes

The engine ECU compares coolant temperature rise with what a working thermostat should allow. It sets these codes when the engine warms up too slowly or does not hold temperature.

FaultCheckMID 128PSID 109FMI 7Volvo/Mack · Coolant thermostat monitoring
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PSID 109 FMI 7 and MID 128 PSID 109 FMI 12 are all about the coolant thermostat monitoring. Most are part or controller faults; none needs an immediate stop. Start with this check: watch coolant temperature on a cold start with the scan tool and note how long it takes to reach operating range.

How urgent are they?

None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.

  • Check soon2

What should I check first?

Watch coolant temperature on a cold start with the scan tool and note how long it takes to reach operating range

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PSID 109 FMI 7Coolant thermostat stuck closed

    The ECM sees coolant temperature behaviour that matches a thermostat stuck closed, so the engine runs hotter than it should.· Part or controller
    Check soon

    Causes

    • Thermostat stuck closed
    • Coolant temperature sensor misreading
    • Low coolant flow

    Checks

    1. 1Watch coolant temperature and feel the upper hose as the engine warms up
    2. 2Check the coolant temperature sensor reading against a thermometer
    3. 3Check the coolant level and look for air in the system
    4. 4Replace the thermostat if it does not open and confirm the code does not return
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Volvo/Mack MID 128 PSID 109 FMI 12Coolant thermostat leaking or stuck open

    The coolant thermostat is leaking or stuck open, so the engine takes too long to warm up and the ECM logs a fault for it.· Part or controller
    Check soon

    Causes

    • Thermostat stuck open
    • Coolant temperature sensor misreading
    • Fan running too much

    Checks

    1. 1Watch the coolant warm-up time in the scan tool on a cold start and compare it with a known good truck
    2. 2Check the coolant temperature sensor reading against a thermometer
    3. 3Check the fan operation, since a fan that stays on keeps the engine cold
    4. 4Replace the thermostat if it leaks or sticks open
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

Shared checks

Checks, in order

  1. 1Watch coolant temperature on a cold start with the scan tool and note how long it takes to reach operating range
  2. 2Feel the upper radiator hose to see if it stays cold when the engine is hot
  3. 3Replace the thermostat with the correct part only after the sensor reading is verified
  4. 4Bleed the cooling system following the workshop procedure and recheck

Causes

  • Thermostat stuck open or closed, or the wrong part fitted
  • Coolant temperature sensor reading wrongly
  • Low coolant or air trapped in the system

Most codes here: part or controller (2 of 2)

Check power and ground at the module connector with the key on, then its fuses.

When to stop

You'll notice: The engine takes a long time to warm up, the cab heater is weak, or the engine runs hot because the thermostat does not open.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.