Volvo/Mack · MID 128 engine ECU - sensors and levels
Volvo/Mack Fault Code MID 128 PID 100 FMI 3
Engine oil pressure sensor circuit shorted or ground open
What does Volvo/Mack code MID 128 PID 100 FMI 3 mean?
The oil pressure sensor signal is outside its valid electrical band. Urgency: check soon - the machine may derate or limit a function. Check first: compare the real pressure with a mechanical gauge first so you know the engine itself is not the problem.
- MID 128
- Which control unit reports it
- PID 100
- Parameter at fault
- FMI 3
- Voltage above normal or shorted high
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Compare the real pressure with a mechanical gauge first so you know the engine itself is not the problem
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Measuring (signal) wire touching battery positive or the 5 V supply somewhere along the engine harness
- Open sensor ground wire so the signal floats up to the supply level
- Engine oil pressure sensor failed internally after oil or heat damage
- Corroded pins in the sensor connector on the block
How it failed
You'll notice: Yellow check lamp is lit and the oil pressure gauge in the cluster sits at 0 even though the engine is running and oil pressure is normal.
Shorted highRead from FMI 3: voltage above normal or shorted high
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Oil pressure, oil level and oil temperature
- MID 128 PID 98 FMI 1Engine oil level critically lowReal conditionStop now
- MID 128 PID 98 FMI 4Engine oil level sensor shorted to groundShorted lowCheck soon
- MID 128 PID 98 FMI 5Engine oil level sensor circuit openOpen circuitCheck soon
- MID 128 PID 100 FMI 1Engine oil pressure critically lowReal conditionStop now
- MID 128 PID 100 FMI 3Engine oil pressure sensor circuit shorted or ground openShorted highCheck soon
- MID 128 PID 100 FMI 5Engine oil pressure sensor circuit open or shorted to groundOpen circuitCheck soon
- MID 128 PID 100 FMI 13Engine oil pressure sensor out of calibrationPart or controllerCheck soon
- MID 128 PID 175 FMI 0Engine oil temperature critically highReal conditionStop now
- MID 128 PID 175 FMI 2Engine oil temperature signal erraticErratic or implausibleCheck soon
Show the other 3 codesHide the other codes
Other Volvo/Mack codes: MID 128 engine ECU - sensors and levels
Related on Equipments Finder
Source
This source lists MID 128 PID 100 FMI 3 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
