Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing
Volvo/Mack Fault Code MID 128 SID 1 FMI 3
Injector cylinder 1 circuit shorted high
What does Volvo/Mack code MID 128 SID 1 FMI 3 mean?
The ECM sees a short to positive on the low-side circuit of the cylinder 1 injector. The injector driver cannot fire the injector normally. Urgency: check soon - the machine may derate or limit a function. Check first: read the code active or inactive and note whether it returns after a clear and restart.
- MID 128
- Which control unit reports it
- SID 1
- Component at fault
- FMI 3
- Voltage above normal or shorted high
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read the code active or inactive and note whether it returns after a clear and restart
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Injector harness for cylinder 1 shorted to positive on the low-side wire
- Injector solenoid with an internal short
- Chafed wire under the valve cover where the harness crosses the rocker area
How it failed
You'll notice: Engine loses power and runs unevenly because cylinder 1 is not firing correctly; MIL and yellow check lamp are lit.
Shorted highRead from FMI 3: voltage above normal or shorted high
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Injector circuits (cylinders 1-6)
- MID 128 SID 1 FMI 3Injector cylinder 1 circuit shorted highShorted highCheck soon
- MID 128 SID 1 FMI 5Injector cylinder 1 circuit open or shorted to groundOpen circuitCheck soon
- MID 128 SID 1 FMI 7Injector cylinder 1 balancing above limitPart or controllerCheck soon
- MID 128 SID 1 FMI 8Injector cylinder 1 misfire detectedErratic or implausibleCheck soon
- MID 128 SID 1 FMI 13Injector cylinder 1 out of calibrationPart or controllerCheck soon
- MID 128 SID 2 FMI 5Injector cylinder 2 circuit open or shortedOpen circuitCheck soon
- MID 128 SID 3 FMI 5Injector cylinder 3 circuit open or shortedOpen circuitCheck soon
- MID 128 SID 4 FMI 5Injector cylinder 4 circuit open or shortedOpen circuitCheck soon
- MID 128 SID 5 FMI 5Injector cylinder 5 circuit open or shortedOpen circuitCheck soon
- MID 128 SID 6 FMI 5Injector cylinder 6 circuit open or shortedOpen circuitCheck soon
Related on Equipments Finder
Source
This source lists MID 128 SID 1 FMI 3 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
