Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
Volvo/Mack Fault Code MID 128 PID 81 FMI 0
DPF differential pressure critically high
What does Volvo/Mack code MID 128 PID 81 FMI 0 mean?
The pressure drop across the diesel particulate filter is critically high. The filter is badly loaded or blocked, or the pressure sensor is reading wrongly. Urgency: stop now - shut down and fix before working on. Check first: read DPF differential pressure at idle and at high idle and compare with the soot load estimate.
- MID 128
- Which control unit reports it
- PID 81
- Parameter at fault
- FMI 0
- Data above normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Read DPF differential pressure at idle and at high idle and compare with the soot load estimate
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- DPF blocked with soot or ash
- DPF differential pressure sensor failed
- Differential pressure hoses blocked or swapped
How it failed
You'll notice: Red stop lamp lit and the engine derates heavily.
Real conditionRead from FMI 0: data above normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: EGR flow and DPF filter pressure drop
2 other codes on this part are also real condition (MID 128 PID 411 FMI 0, MID 128 PID 411 FMI 1). When they show together, start at the wiring and connector they share.
- MID 128 PID 81 FMI 0DPF differential pressure critically highReal conditionStop now
- MID 128 PID 81 FMI 3DPF differential pressure sensor signal highShorted highCheck soon
- MID 128 PID 81 FMI 5DPF differential pressure sensor circuit openOpen circuitCheck soon
- MID 128 PID 411 FMI 0EGR differential pressure reads too highReal conditionCheck soon
- MID 128 PID 411 FMI 1EGR differential pressure reads too lowReal conditionCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
- MID 128 PPID 326 FMI 11DPF soot level critically high
- MID 128 PSID 46 FMI 0SCR system severe fault - operator inducement
- MID 128 PSID 47 FMI 0Unable to reach regeneration temperature
- MID 128 PSID 47 FMI 1Aftertreatment temperature too high during regeneration
- MID 128 PSID 90 FMI 1DEF dosing too low - NOx limits exceeded, poor DEF quality
- MID 128 PSID 90 FMI 7DEF dosing interrupted - NOx limits exceeded
Related on Equipments Finder
Source
This source lists MID 128 PID 81 FMI 0 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
