Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
Volvo/Mack Fault Code MID 128 PSID 47 FMI 0
Unable to reach regeneration temperature
What does Volvo/Mack code MID 128 PSID 47 FMI 0 mean?
The aftertreatment cannot reach the temperature needed for regeneration. Mack lists a clogged hydrocarbon doser and low doser fuel pressure. Urgency: check soon - the machine may derate or limit a function. Check first: check doser fuel pressure while the regeneration runs.
- MID 128
- Which control unit reports it
- PSID 47
- Maker component at fault
- FMI 0
- Data above normal, most severe
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check doser fuel pressure while the regeneration runs
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Aftertreatment hydrocarbon doser clogged
- Doser fuel pressure too low
- Exhaust temperature sensor misreading
How it failed
You'll notice: MIL lit and the regeneration may be incomplete, so soot keeps building in the filter.
Real conditionRead from FMI 0: data above normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DPF regeneration temperature
1 other code on this part is also real condition (MID 128 PSID 47 FMI 1). When they show together, start at the wiring and connector they share.
- MID 128 PSID 47 FMI 0Unable to reach regeneration temperatureReal conditionCheck soon
- MID 128 PSID 47 FMI 1Aftertreatment temperature too high during regenerationReal conditionCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
- MID 128 PSID 90 FMI 1DEF dosing too low - NOx limits exceeded, poor DEF quality
- MID 128 PSID 90 FMI 7DEF dosing interrupted - NOx limits exceeded
- MID 128 PSID 121 FMI 7DEF pressure build-up failure - loss of prime
- MID 128 PPID 270 FMI 2Outlet NOx sensor reading not plausible
- MID 128 PPID 270 FMI 3Outlet NOx sensor signal shorted high
- MID 128 PPID 270 FMI 5Outlet NOx sensor circuit open
- MID 128 PPID 270 FMI 9Outlet NOx sensor signal missing
Related on Equipments Finder
Source
This source lists MID 128 PSID 47 FMI 0 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
