EF Logo

Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)

Volvo/Mack DPF regeneration temperature fault codes

During regeneration the aftertreatment must reach and hold a target temperature. These codes are set when it cannot get there or gets too hot.

FaultCheckMID 128PSID 47FMI 0Volvo/Mack · DPF regeneration temperature
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PSID 47 FMI 0 and MID 128 PSID 47 FMI 1 are all about the dPF regeneration temperature. Most are real condition faults; none needs an immediate stop. Start with this check: check the exhaust temperature sensors and compare their readings at the same load for a believable spread.

How urgent are they?

None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.

  • Check soon2

What should I check first?

Check the exhaust temperature sensors and compare their readings at the same load for a believable spread

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PSID 47 FMI 0Unable to reach regeneration temperature

    The aftertreatment cannot reach the temperature needed for regeneration.· Real condition
    Check soon

    Causes

    • Aftertreatment hydrocarbon doser clogged
    • Doser fuel pressure too low
    • Exhaust temperature sensor misreading

    Checks

    1. 1Check doser fuel pressure while the regeneration runs
    2. 2Inspect the doser nozzle for deposits for damage, corrosion or looseness
    3. 3Check the exhaust temperature sensors for correct readings
    4. 4Check for exhaust and intake air leaks that cool the exhaust
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PSID 47 FMI 1Aftertreatment temperature too high during regeneration

    The aftertreatment temperature became too high.· Real condition
    Check soon

    Causes

    • Doser clogged
    • Doser fuel pressure too high
    • Exhaust temperature sensor fault

    Checks

    1. 1Check doser fuel pressure and compare with the expected value
    2. 2Check the doser for leakage or sticking open for damage, corrosion or looseness
    3. 3Check the temperature sensors in the exhaust for correct readings
    4. 4Check the fuel shutoff valve for leakage for damage, corrosion or looseness
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Check the exhaust temperature sensors and compare their readings at the same load for a believable spread
  2. 2Check the hydrocarbon doser operation with the scan tool and look for a clogged or leaking nozzle
  3. 3Inspect the exhaust system for leaks that let heat escape before the aftertreatment can reach temperature
  4. 4Check the diesel oxidation catalyst for soot, oil or fuel contamination that stops it from lighting off

Causes

  • Doser or injector fault
  • Exhaust temperature sensor fault
  • Exhaust leak or restricted DOC

Most codes here: real condition (2 of 2)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The DPF lamp stays on and regeneration fails or the exhaust runs very hot.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.