EF Logo

Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)

Volvo/Mack DPF soot level fault codes

The engine ECU estimates the soot in the DPF. When the level is high the truck needs a regeneration, and if it is ignored it needs a service regeneration.

FaultCheckMID 128PPID 326FMI 0Volvo/Mack · DPF soot level
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PPID 326 FMI 0 and MID 128 PPID 326 FMI 11 are all about the dPF soot level. Most are real condition faults; 1 needs an immediate stop. Start with this check: perform a parked or service regeneration.

How urgent are they?

1 of 2 codes here means stop now; the other 1 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon1

What should I check first?

Perform a parked or service regeneration

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PPID 326 FMI 0DPF soot level moderately high

    The DPF system monitor reports a moderately high soot load.· Real condition
    Check soon

    Causes

    • Diesel particulate filter clogged
    • Hydrocarbon doser (fuel injector) clogged
    • Regeneration disabled by the driver or another component

    Checks

    1. 1Check why regeneration did not run; look at the inhibit switch and regeneration history
    2. 2Check the doser fuel pressure and spray pattern
    3. 3Run a parked regeneration with the tool before you replace any parts
    4. 4Inspect the DPF for blockage when other checks pass
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PPID 326 FMI 11DPF soot level critically high

    The soot load in the DPF is critically high.· Real condition
    Stop now

    Causes

    • Diesel particulate filter clogged
    • Aftertreatment hydrocarbon doser failure
    • Regeneration disabled by the driver or another component

    Checks

    1. 1Do not keep driving under load; arrange a service regeneration first
    2. 2Check the doser and its fuel pressure for damage, corrosion or looseness
    3. 3Check for other active codes that disable regeneration
    4. 4Inspect the DPF for blockage or a melted core
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Perform a parked or service regeneration
  2. 2Check the differential pressure sensor reading and its hoses, because a faulty sensor gives a false soot value
  3. 3Check for injector or EGR faults that make the engine produce more soot than normal and fill the filter
  4. 4Check the DPF condition by the pressure drop and, if needed, remove it for a visual and weight check

Causes

  • Short trips and idling that prevent regeneration
  • Faulty injection or EGR raising soot
  • Pressure sensor fault

Most codes here: real condition (2 of 2)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The DPF lamp comes on and the engine derates if the level gets critical.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.