Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
Volvo/Mack Fault Code MID 128 PPID 326 FMI 0
DPF soot level moderately high
What does Volvo/Mack code MID 128 PPID 326 FMI 0 mean?
The DPF system monitor reports a moderately high soot load. Mack lists a clogged DPF, a clogged hydrocarbon doser or regeneration being disabled. Urgency: check soon - the machine may derate or limit a function. Check first: check why regeneration did not run; look at the inhibit switch and regeneration history.
- MID 128
- Which control unit reports it
- PPID 326
- Maker parameter at fault
- FMI 0
- Data above normal, most severe
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check why regeneration did not run; look at the inhibit switch and regeneration history
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Diesel particulate filter clogged
- Hydrocarbon doser (fuel injector) clogged
- Regeneration disabled by the driver or another component
How it failed
You'll notice: Yellow lamp lit and the engine derates at a medium to high level until the soot is burned off.
Real conditionRead from FMI 0: data above normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DPF soot level
1 other code on this part is also real condition (MID 128 PPID 326 FMI 11). When they show together, start at the wiring and connector they share.
- MID 128 PPID 326 FMI 0DPF soot level moderately highReal conditionCheck soon
- MID 128 PPID 326 FMI 11DPF soot level critically highReal conditionStop now
Other Volvo/Mack codes: MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
- MID 128 PSID 47 FMI 0Unable to reach regeneration temperature
- MID 128 PSID 46 FMI 0SCR system severe fault - operator inducement
- MID 128 PSID 47 FMI 1Aftertreatment temperature too high during regeneration
- MID 128 PID 81 FMI 0DPF differential pressure critically high
- MID 128 PID 81 FMI 3DPF differential pressure sensor signal high
- MID 128 PID 81 FMI 5DPF differential pressure sensor circuit open
- MID 128 PSID 90 FMI 1DEF dosing too low - NOx limits exceeded, poor DEF quality
Related on Equipments Finder
Source
This source lists MID 128 PPID 326 FMI 0 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
