EF Logo

Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake

Volvo/Mack EGR flow and DPF filter pressure drop fault codes

Both are differential pressure sensors read by the engine ECU on MID 128, but they watch different parts. The EGR sensor (PID 411) measures the drop across the EGR cooler or venturi so the ECU can work out EGR flow.

More about these parts

The DPF sensor (PID 81) measures the drop across the particulate filter so the ECU can judge how loaded the filter is.

FaultStopMID 128PID 81FMI 0Volvo/Mack · EGR flow and DPF filter pressure drop
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PID 81 FMI 0 to MID 128 PID 411 FMI 1 are all about the eGR flow and DPF filter pressure drop. Most are real condition faults; 1 needs an immediate stop. Start with this check: read each sensor with the engine off; both should be near zero before any hose is touched.

How urgent are they?

1 of 5 codes here means stop now; the other 4 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon4

What should I check first?

Read each sensor with the engine off; both should be near zero before any hose is touched

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PID 81 FMI 0DPF differential pressure critically high

    The pressure drop across the diesel particulate filter is critically high.· Real condition
    Stop now

    Causes

    • DPF blocked with soot or ash
    • DPF differential pressure sensor failed
    • Differential pressure hoses blocked or swapped

    Checks

    1. 1Read DPF differential pressure at idle and at high idle and compare with the soot load estimate
    2. 2Check the pressure sensor hoses for kinks, cracks, soot blockage or water
    3. 3Check the pressure sensor against ambient at key on
    4. 4Run a forced regeneration with the tool if the truck permits
    5. 5Inspect the DPF and the exhaust for restriction or damage
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PID 81 FMI 3DPF differential pressure sensor signal high

    The DPF differential pressure sensor signal is high, from a short to battery on the metering side or an open ground.· Shorted high
    Check soon

    Causes

    • Short to battery on the metering side
    • Open in the ground line
    • Faulty DPF differential pressure sensor

    Checks

    1. 1Check the sensor plug for 5 V supply and ground with the key on
    2. 2Test the signal wire for a short to battery with the key off
    3. 3Check ground continuity from the sensor plug to the ECM
    4. 4Replace the DPF differential pressure sensor after the harness passes
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 PID 81 FMI 5DPF differential pressure sensor circuit open

    The DPF differential pressure sensor circuit is open in the 5 V supply or the metering line, or shorted to ground.· Open circuit
    Check soon

    Causes

    • Open 5 V supply
    • Short to ground in the metering line
    • Open metering line
    • Faulty sensor

    Checks

    1. 1Check the 5 V supply at the sensor plug with the key on
    2. 2Check the signal wire for continuity and for a short to ground
    3. 3Inspect the harness and connector near the DPF for heat damage
    4. 4Replace the sensor if the wiring tests good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 PID 411 FMI 0EGR differential pressure reads too high

    The EGR differential pressure sensor output is too high, from a leak or a clogged EGR cooler or sensor fault.· Real condition
    Check soon

    Causes

    • Clogged EGR cooler
    • EGR system leak
    • EGR differential pressure sensor failing
    • Damaged sensor harness or connector

    Checks

    1. 1Read EGR differential pressure at key on; it should be near zero with no flow
    2. 2Check the EGR hoses and lines for leaks and for soot-blocked sensing lines
    3. 3Inspect the EGR cooler for blockage
    4. 4Replace the sensor after the lines and cooler pass
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PID 411 FMI 1EGR differential pressure reads too low

    The EGR differential pressure sensor output is too low.· Real condition
    Check soon

    Causes

    • Clogged EGR venturi
    • Faulty EGR differential pressure sensor
    • Damaged harness or connector

    Checks

    1. 1Check differential pressure with the EGR valve commanded open and compare it with key-on zero
    2. 2Inspect the venturi for soot blockage for damage, corrosion or looseness
    3. 3Check the sensor harness and connector for damage
    4. 4Replace the sensor if the venturi is clear and the harness good
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Read each sensor with the engine off; both should be near zero before any hose is touched
  2. 2Inspect the sensor hoses for blockage, water and cracks
  3. 3For an EGR code, check the EGR cooler for fouling and leaks and the venturi for clogging
  4. 4For a DPF code, check the filter for blockage and run a regeneration with the scan tool
  5. 5Check the sensor connector for corrosion and measure the supply voltage at the plug with the key on

Causes

  • Sensor hoses blocked with soot or condensate, or cracked
  • EGR cooler fouled or leaking, or a clogged venturi
  • DPF blocked with soot or ash
  • Sensor failed, or open or shorted on its 5 V supply or signal line

Most codes here: real condition (3 of 5)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: A check lamp comes on.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.