EF Logo

Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake

Volvo/Mack Boost pressure and charge air temperature fault codes

Two sensors on the intake manifold report the charge air after the turbocharger and cooler to the engine ECU on MID 128. The boost pressure sensor (PID 102) gives the air pressure used to control the turbo and fuelling.

More about these parts

The intake manifold temperature sensor (PID 105) gives the air temperature used to adjust fuelling and protect the engine.

FaultCheckMID 128PID 102FMI 3Volvo/Mack · Boost pressure and charge air temperature
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PID 102 FMI 2 to MID 128 PID 105 FMI 5 are all about the boost pressure and charge air temperature. The most common failure type is open circuit (2 of 5); none needs an immediate stop. Start with this check: read the boost value with the key on and engine off; it should show ambient pressure.

How urgent are they?

None of the 5 codes here means stop now; all 5 can wait until the shift ends, but find the cause before the next one.

  • Check soon5

What should I check first?

Read the boost value with the key on and engine off; it should show ambient pressure

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PID 102 FMI 2Intake manifold (boost) pressure signal erratic or implausible

    The boost pressure value jumps or does not match what the turbocharger and engine load should produce.· Erratic or implausible
    Check soon

    Causes

    • Intake manifold pressure sensor reading incorrectly
    • Damaged harness or loose connector near the sensor
    • Sensor port blocked with oily deposits

    Checks

    1. 1Compare boost with barometric pressure at key on, then against a manual gauge under load
    2. 2Wiggle the harness and watch for jumps in the live value
    3. 3Clean oily carbon out of the sensor port and any hose to it
    4. 4Replace the sensor if the value stays wrong with a good harness
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Volvo/Mack MID 128 PID 102 FMI 3Intake manifold (boost) pressure sensor signal high

    The boost pressure sensor signal is above its valid range.· Shorted high
    Check soon

    Causes

    • Short to battery on the sensor metering (signal) wire
    • Open ground wire so the signal floats up
    • Intake manifold pressure sensor failed high
    • Harness connector corroded at the sensor on the intake side

    Checks

    1. 1Key on, engine off: the reading should equal barometric pressure; a stuck high value confirms the fault
    2. 2Unplug the sensor and measure the 5 V supply and ground at the harness plug
    3. 3Probe the signal wire with the key off for a short to battery positive
    4. 4Check ground continuity from the sensor plug to the ECM
    5. 5Replace the sensor after the harness passes and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 PID 102 FMI 5Intake manifold (boost) pressure sensor circuit open or shorted to ground

    The boost pressure sensor signal is low or missing.· Open circuit
    Check soon

    Causes

    • Short to ground on the metering wire in the harness
    • Open in the 5 V supply wire to the sensor
    • Open in the metering wire
    • Pressure sensor failed low

    Checks

    1. 1Read boost pressure with the key on; a value below ambient shows a low-side fault
    2. 2Unplug the sensor and verify 5 V on the supply pin of the harness plug
    3. 3Test the signal wire for continuity and for a short to ground with the key off
    4. 4Check the connector for pushed-back pins and oil in the plug
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 PID 105 FMI 4Intake manifold temperature sensor shorted to ground

    The intake manifold temperature signal is pulled low, so the ECM sees an impossibly cold charge air value.· Shorted low
    Check soon

    Causes

    • Manifold temperature sensor shorted internally
    • Signal wire chafed to ground
    • Damaged connector

    Checks

    1. 1Read the live temperature; a value far below ambient confirms the fault
    2. 2Unplug the sensor and test the signal wire for a short to ground
    3. 3Inspect the harness and connector on the intake side for damage
    4. 4Replace the sensor if the wiring is good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Volvo/Mack MID 128 PID 105 FMI 5Intake manifold temperature sensor circuit open

    The ECM sees the intake manifold temperature circuit as open, or possibly shorted to the sensor.· Open circuit
    Check soon

    Causes

    • Open wire to the temperature sensor
    • Sensor failed open
    • Connector off or pin backed out

    Checks

    1. 1Read the live value; a fixed extreme value points to an open circuit
    2. 2Check continuity of the sensor wiring to the ECM
    3. 3Reseat the connector and look for pushed-back pins
    4. 4Replace the sensor if the wiring tests OK and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Read the boost value with the key on and engine off; it should show ambient pressure
  2. 2Check the charge air pipes, cooler and clamps for leaks that would also lower boost
  3. 3Compare the intake temperature reading with ambient on a cold engine
  4. 4Measure the 5 V supply and ground at the sensor plug, then check the signal wire for a short to ground or an open
  5. 5Inspect the boost sensor port for oil or soot and the harness near the manifold for heat damage

Causes

  • Boost sensor failed, or its port blocked with oil or soot
  • Temperature sensor failed or its connector corroded
  • Harness short or open between a manifold sensor and the ECU
  • Loose charge air hose or clamp that really lowers boost

Most common here: open circuit (2 of 5)

Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

When to stop

You'll notice: The engine feels down on power and may show black smoke, or has slightly reduced power in hot weather, and a check lamp comes on.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.