EF Logo

Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake

Volvo/Mack EGR temperature sensor fault codes

The EGR temperature sensor measures the temperature of the recirculated exhaust gas, which the ECU uses to check cooler performance.

FaultCheckMID 128PID 412FMI 4Volvo/Mack · EGR temperature sensor
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PID 412 FMI 4 and MID 128 PID 412 FMI 5 are all about the eGR temperature sensor. None needs an immediate stop. Start with this check: inspect the sensor connector for corrosion and heat damage.

How urgent are they?

None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.

  • Check soon2

What should I check first?

Inspect the sensor connector for corrosion and heat damage

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PID 412 FMI 4EGR temperature sensor shorted to ground

    The EGR temperature sensor circuit is shorted to ground on the metering side.· Shorted low
    Check soon

    Causes

    • EGR temperature sensor shorted
    • Sensor harness shorted to ground
    • Damaged connector

    Checks

    1. 1Read the live EGR temperature and compare with coolant temperature on a cold engine
    2. 2Unplug the sensor and check the harness for shorts to ground
    3. 3Inspect the connector near the EGR cooler for heat damage
    4. 4Replace the sensor if the wiring is good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Volvo/Mack MID 128 PID 412 FMI 5EGR temperature sensor circuit open

    The EGR temperature sensor circuit is open or shorted to battery on the metering side.· Open circuit
    Check soon

    Causes

    • Open in the EGR temperature sensor circuit
    • Short to battery
    • Failed sensor

    Checks

    1. 1Read the live EGR temperature; a fixed value suggests an open circuit
    2. 2Check continuity of both sensor wires to the ECM
    3. 3Inspect the connector near the EGR cooler for heat damage
    4. 4Replace the sensor if the wiring tests good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Inspect the sensor connector for corrosion and heat damage
  2. 2Check the signal wire for a short to ground and an open circuit
  3. 3Compare the reading with other temperatures on a cold engine
  4. 4Replace the sensor only once the supply, ground and signal wiring have been proven clean

Causes

  • Sensor failed from heat
  • Shorted or open wiring
  • Corroded connector

When to stop

You'll notice: A check lamp comes on and the engine may run with reduced EGR.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.