EF Logo

Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake

Volvo/Mack Exhaust gas temperature sensor fault codes

Exhaust temperature sensors in the aftertreatment give the engine ECU temperatures it needs for regeneration and protection. These codes cover a hot exhaust and circuit faults.

FaultStopMID 128PID 173FMI 0Volvo/Mack · Exhaust gas temperature sensor
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PID 173 FMI 0 to MID 128 PID 173 FMI 5 are all about the exhaust gas temperature sensor. 1 needs an immediate stop. Start with this check: compare the reading with the other exhaust sensors at the same engine load.

How urgent are they?

1 of 4 codes here means stop now; the other 3 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon3

What should I check first?

Compare the reading with the other exhaust sensors at the same engine load

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PID 173 FMI 0Exhaust gas temperature critically high

    The exhaust gas temperature reading is critically high.· Real condition
    Stop now

    Causes

    • Intake air leak causing lean, hot combustion
    • Faulty harness or connector at the EGT sensor
    • Overloaded engine or restricted exhaust or charge air

    Checks

    1. 1Look at live EGT while driving under load and compare the readings of the front and rear exhaust sensors
    2. 2Check intake piping and clamps for leaks that would make the engine run lean and hot
    3. 3Check the sensor connector for heat damage and loose pins
    4. 4Inspect the exhaust and the DPF for restriction
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PID 173 FMI 2Exhaust gas temperature signal not rational

    The EGT sensor value does not make sense compared with engine load and other temperatures.· Erratic or implausible
    Check soon

    Causes

    • EGT sensor failing
    • Damaged harness or connector
    • Exhaust leak or intake air leak upsetting the reading

    Checks

    1. 1Compare EGT with other exhaust temperature sensors under the same load
    2. 2Look for exhaust leaks around the sensor and flange
    3. 3Inspect the connector and harness for heat damage
    4. 4Replace the sensor if the signal remains implausible
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Volvo/Mack MID 128 PID 173 FMI 4Exhaust gas temperature sensor shorted to ground

    The ECM sees the EGT signal pulled low, which Mack ties to a short to ground on the metering side.· Shorted low
    Check soon

    Causes

    • EGT sensor failed
    • Harness shorted to ground
    • Faulty connector
    • Aftertreatment control module fault

    Checks

    1. 1Read live EGT with the engine running; it should rise with load, a value stuck low confirms the fault
    2. 2Unplug the sensor and check the signal wire for a short to ground
    3. 3Inspect the harness and connector near the exhaust for heat damage
    4. 4Replace the sensor if the harness is good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Volvo/Mack MID 128 PID 173 FMI 5Exhaust gas temperature sensor circuit open

    The EGT sensor circuit is open or shorted to battery, so the ECM gets no usable exhaust temperature.· Open circuit
    Check soon

    Causes

    • Open in the metering or ground side of the circuit
    • Short to battery on the metering side
    • Sensor failure
    • Connector fault

    Checks

    1. 1Read live EGT with the engine running; a fixed high or maximum value suggests an open
    2. 2Check continuity of the signal and ground wires to the ECM
    3. 3Check for a short to battery on the signal wire with the key off
    4. 4Replace the sensor after the wiring tests good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Compare the reading with the other exhaust sensors at the same engine load
  2. 2Inspect the sensor connector and harness for heat damage
  3. 3Measure the sensor resistance cold and compare it with the service data
  4. 4Check for a blocked DPF before replacing the sensor

Causes

  • Sensor failed from heat and vibration
  • Wire burned or chafed near the exhaust
  • Real overtemperature from a blocked or regenerating filter

When to stop

You'll notice: A check or stop lamp comes on and the engine may derate when the exhaust is really too hot.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.