EF Logo

Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake

Volvo/Mack EGR valve control fault codes

The EGR valve lets exhaust gas back into the intake to lower combustion temperature. The engine ECU drives it electrically and checks the circuit.

FaultCheckMID 128SID 146FMI 3Volvo/Mack · EGR valve control
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 SID 146 FMI 3 and MID 128 SID 146 FMI 5 are all about the eGR valve control. None needs an immediate stop. Start with this check: remove the EGR valve and look for heavy soot that stops it from moving.

How urgent are they?

None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.

  • Check soon2

What should I check first?

Remove the EGR valve and look for heavy soot that stops it from moving

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 SID 146 FMI 3EGR valve control shorted high or stuck

    The EGR valve control circuit is shorted to positive or to ground, or the valve is stuck.· Shorted high
    Check soon

    Causes

    • EGR valve stuck from soot
    • EGR valve circuit shorted to positive or ground
    • Damaged harness or connector
    • Faulty EGR valve actuator

    Checks

    1. 1Command the EGR valve in the scan tool and see whether it moves and reports position
    2. 2Inspect the EGR valve connector for heat damage
    3. 3Check the wiring for shorts to positive and to ground
    4. 4Remove and inspect the valve for soot sticking
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 SID 146 FMI 5EGR valve control circuit open

    The EGR valve control circuit is open, so the ECM cannot drive the valve and cannot control EGR flow.· Open circuit
    Check soon

    Causes

    • Open EGR valve circuit wiring
    • EGR valve actuator failed open
    • Connector fault

    Checks

    1. 1Check continuity of the EGR valve control wires to the ECM
    2. 2Inspect the valve connector for pushed-back pins and heat damage
    3. 3Measure the valve actuator resistance if the manual gives a value
    4. 4Replace the valve if the wiring tests good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Remove the EGR valve and look for heavy soot that stops it from moving
  2. 2Check the valve connector and harness for damage and corrosion
  3. 3Command the valve with the scan tool and watch the position feedback
  4. 4Check the supply and ground at the valve plug with the key on

Causes

  • EGR valve stuck from soot or its motor failed
  • Wire shorted high or open in the valve harness
  • Connector corroded or pins pushed back

When to stop

You'll notice: The engine runs rough or lacks power, black smoke may appear, and a check lamp comes on.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.