Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake
Volvo/Mack EGR mass flow fault codes
The engine ECU compares the calculated EGR mass flow with the target. A mismatch means the EGR system is passing too little or too much exhaust gas.
Where to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
What do these codes mean?
Volvo/Mack codes MID 128 PPID 35 FMI 0 and MID 128 PPID 35 FMI 1 are all about the eGR mass flow. Most are real condition faults; none needs an immediate stop. Start with this check: inspect the EGR valve and pipes for soot buildup.
How urgent are they?
None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.
- Check soon2
What should I check first?
Inspect the EGR valve and pipes for soot buildup
Shared checksStop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Volvo/Mack MID 128 PPID 35 FMI 0EGR mass flow too high
The EGR flow is higher than the ECM expects. Only reported on the J1587 link in some cases. Mack lists a faulty EGR system.· Real conditionReal conditionCheck soonCauses
- EGR valve stuck open
- EGR system fault
- Faulty harness or connector
Checks
- 1Command the EGR valve closed and see whether the flow drops
- 2Check the valve position feedback in the scan tool
- 3Inspect the harness and connector for damage for damage, corrosion or looseness
- 4Replace the valve if it sticks open
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Volvo/Mack MID 128 PPID 35 FMI 1EGR mass flow too low
The EGR mass flow is below the expected value. Mack lists a faulty EGR system or a clogged EGR cooler.· Real conditionReal conditionCheck soonCauses
- Clogged EGR cooler
- EGR valve not opening properly
- EGR passages blocked with soot
Checks
- 1Command the EGR valve open and watch the flow and differential pressure
- 2Inspect the EGR cooler and pipes for blockage
- 3Check the venturi and the EGR differential pressure sensor
- 4Clean or replace the clogged parts
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Inspect the EGR valve and pipes for soot buildup
- 2Check the EGR cooler and its passages for restrictions and soot that would hold back the gas flow
- 3Verify the differential pressure sensor reading
- 4Check for exhaust leaks before the sensor
Causes
- EGR valve stuck or fouled with soot
- Blocked EGR cooler or passages
- Differential pressure sensor or hoses fault
Most codes here: real condition (2 of 2)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: The engine runs rough, loses power or smokes, and a check lamp comes on.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
