EF Logo

Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake

Volvo/Mack Turbo boost pressure control fault codes

The engine ECU compares the actual boost with the target for the current load. These codes are set when boost is clearly too high or too low even though the sensor itself reads plausibly.

FaultCheckMID 128PSID 98FMI 0Volvo/Mack · Turbo boost pressure control
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PSID 98 FMI 0 and MID 128 PSID 98 FMI 1 are all about the turbo boost pressure control. Most are real condition faults; none needs an immediate stop. Start with this check: pressure test the charge air system for leaks at the hoses and cooler.

How urgent are they?

None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.

  • Check soon2

What should I check first?

Pressure test the charge air system for leaks at the hoses and cooler

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PSID 98 FMI 0Turbocharger boost pressure too high

    The turbocharger boost pressure is higher than the ECM wants.· Real condition
    Check soon

    Causes

    • EGR system failure
    • Faulty turbocharger outlet pressure sensor
    • VGT nozzle stuck closed

    Checks

    1. 1Compare boost with the commanded value under load in the scan tool
    2. 2Check the VGT actuator operation across its range
    3. 3Check the EGR system operation and valve position
    4. 4Test the boost pressure sensor against a manual gauge
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PSID 98 FMI 1Turbocharger boost pressure too low

    Boost pressure is lower than the ECM wants.· Real condition
    Check soon

    Causes

    • Air leak in turbo hoses, pipes, brackets or the charge air cooler
    • EGR system fault, such as a valve stuck open
    • VGT nozzle stuck open
    • Exhaust leak before the turbo

    Checks

    1. 1Smoke or pressure test the charge air system for leaks
    2. 2Inspect all hose clamps and the charge air cooler for splits
    3. 3Check VGT operation and EGR valve position in the scan tool
    4. 4Look for exhaust leaks around the manifold and turbo flange
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Pressure test the charge air system for leaks at the hoses and cooler
  2. 2Check the air filter restriction and the exhaust for blockage
  3. 3Compare actual and target boost on the scan tool under load
  4. 4Check that the turbo actuator moves through its full range

Causes

  • Leak in the charge air cooler or its pipes (low boost)
  • Turbo vanes or wastegate sticking
  • Blocked air filter or exhaust restriction

Most codes here: real condition (2 of 2)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The engine lacks power or surges, the exhaust may smoke, and a check lamp comes on.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.