EF Logo

Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake

Volvo/Mack Engine compression brake output fault codes

The engine ECU switches the solenoids of the engine compression brake. These codes are about that output circuit.

FaultCheckMID 128PPID 122FMI 3Volvo/Mack · Engine compression brake output
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PPID 122 FMI 3, MID 128 PPID 122 FMI 4 and MID 128 PPID 122 FMI 5 are all about the engine compression brake output. 1 needs an immediate stop. Start with this check: measure the solenoid coil resistance against the service data.

How urgent are they?

1 of 3 codes here means stop now; the other 2 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon2

What should I check first?

Measure the solenoid coil resistance against the service data

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PPID 122 FMI 3Engine compression brake output shorted high

    The engine compression brake output circuit is shorted to positive.· Shorted high
    Check soon

    Causes

    • Compression brake solenoid with an internal short to supply
    • Brake harness shorted to battery positive near the valve cover
    • Damaged valve cover connector

    Checks

    1. 1Check the compression brake solenoids at the valve cover for damage and oil
    2. 2Check the brake harness for a short to positive with the key off
    3. 3Measure the solenoid resistance at the connector
    4. 4Replace the faulty actuator after the harness tests good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 PPID 122 FMI 4Engine compression brake output shorted low

    The engine compression brake output is shorted to ground.· Shorted low
    Stop now

    Causes

    • Brake solenoid with an internal short to ground
    • Brake harness rubbed through to ground at the valve cover
    • Oil-soaked valve cover connector bridging to ground

    Checks

    1. 1Unplug the compression brake solenoids at the valve cover one at a time; if the engine recovers, the last one is shorted
    2. 2Look for a rubbed-through brake wire where the harness crosses the valve cover gasket
    3. 3Measure each solenoid coil resistance and compare them with each other
    4. 4Make sure the engine is restartable before road testing, since the brake can lock on
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Volvo/Mack MID 128 PPID 122 FMI 5Engine compression brake output circuit open

    The engine compression brake circuit is open, so the brake cannot be turned on.· Open circuit
    Check soon

    Causes

    • Open circuit in the brake wiring
    • Failed brake actuator
    • Connector fault at the valve cover

    Checks

    1. 1Check continuity of the brake solenoid wires to the ECM
    2. 2Inspect the valve cover connector for oil and corrosion
    3. 3Measure the solenoid resistance at the connector
    4. 4Replace the actuator if the wiring tests good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Measure the solenoid coil resistance against the service data
  2. 2Inspect the connector under the valve cover for oil and heat damage
  3. 3Check the wire between the ECU and the solenoid for shorts and breaks
  4. 4Test the brake with the scan tool command after the repair

Causes

  • Engine brake solenoid coil failed
  • Short to ground or battery in the solenoid wiring
  • Open circuit at the valve cover connector

When to stop

You'll notice: The engine brake does not work or works with no request, and a check lamp comes on, which the driver notices on a long downhill.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.