Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake
Volvo/Mack Fault Code MID 128 PPID 122 FMI 3
Engine compression brake output shorted high
What does Volvo/Mack code MID 128 PPID 122 FMI 3 mean?
The engine compression brake output circuit is shorted to positive. The brake cannot be turned on, and shift quality on some automatic transmissions can be derated. Urgency: check soon - the machine may derate or limit a function. Check first: check the compression brake solenoids at the valve cover for damage and oil.
- MID 128
- Which control unit reports it
- PPID 122
- Maker parameter at fault
- FMI 3
- Voltage above normal or shorted high
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the compression brake solenoids at the valve cover for damage and oil
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Compression brake solenoid with an internal short to supply
- Brake harness shorted to battery positive near the valve cover
- Damaged valve cover connector
How it failed
You'll notice: Yellow check lamp lit; no engine brake and shift quality on some automatics may be derated.
Shorted highRead from FMI 3: voltage above normal or shorted high
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine compression brake output
- MID 128 PPID 122 FMI 3Engine compression brake output shorted highShorted highCheck soon
- MID 128 PPID 122 FMI 4Engine compression brake output shorted lowShorted lowStop now
- MID 128 PPID 122 FMI 5Engine compression brake output circuit openOpen circuitCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - air, turbo, EGR and brake
- MID 128 SID 27 FMI 2Variable geometry turbo actuator - no valid command received
- MID 128 SID 27 FMI 4Variable geometry turbo actuator shorted to ground
- MID 128 SID 27 FMI 7Variable geometry turbo actuator mechanical fault
- MID 128 SID 27 FMI 9Variable geometry turbo actuator data missing for 2 seconds
- MID 128 SID 27 FMI 13Variable geometry turbo actuator self-calibration failed
- MID 128 PPID 35 FMI 0EGR mass flow too high
- MID 128 PPID 35 FMI 1EGR mass flow too low
Related on Equipments Finder
Source
This source lists MID 128 PPID 122 FMI 3 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
