Volvo/Mack · MID 128 engine ECU - air, turbo, EGR and brake
Volvo/Mack Fault Code MID 128 PID 102 FMI 3
Intake manifold (boost) pressure sensor signal high
What does Volvo/Mack code MID 128 PID 102 FMI 3 mean?
The boost pressure sensor signal is above its valid range. Mack names a short to battery in the metering circuit or an open in the sensor ground as the conditions, so the ECM loses its boost measurement. Urgency: check soon - the machine may derate or limit a function. Check first: key on, engine off: the reading should equal barometric pressure; a stuck high value confirms the fault.
- MID 128
- Which control unit reports it
- PID 102
- Parameter at fault
- FMI 3
- Voltage above normal or shorted high
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Key on, engine off: the reading should equal barometric pressure; a stuck high value confirms the fault
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Short to battery on the sensor metering (signal) wire
- Open ground wire so the signal floats up
- Intake manifold pressure sensor failed high
- Harness connector corroded at the sensor on the intake side
How it failed
You'll notice: Engine goes into derate, the MIL lights and the truck feels flat under load.
Shorted highRead from FMI 3: voltage above normal or shorted high
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Boost pressure and charge air temperature
- MID 128 PID 102 FMI 2Intake manifold (boost) pressure signal erratic or implausibleErratic or implausibleCheck soon
- MID 128 PID 102 FMI 3Intake manifold (boost) pressure sensor signal highShorted highCheck soon
- MID 128 PID 102 FMI 5Intake manifold (boost) pressure sensor circuit open or shorted to groundOpen circuitCheck soon
- MID 128 PID 105 FMI 4Intake manifold temperature sensor shorted to groundShorted lowCheck soon
- MID 128 PID 105 FMI 5Intake manifold temperature sensor circuit openOpen circuitCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - air, turbo, EGR and brake
- MID 128 SID 27 FMI 2Variable geometry turbo actuator - no valid command received
- MID 128 SID 27 FMI 4Variable geometry turbo actuator shorted to ground
- MID 128 SID 27 FMI 7Variable geometry turbo actuator mechanical fault
- MID 128 SID 27 FMI 9Variable geometry turbo actuator data missing for 2 seconds
- MID 128 SID 27 FMI 13Variable geometry turbo actuator self-calibration failed
- MID 128 PPID 35 FMI 0EGR mass flow too high
Related on Equipments Finder
Source
This source lists MID 128 PID 102 FMI 3 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
