EF Logo

Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)

Volvo/Mack DEF dosing performance fault codes

The engine ECU monitors how well the SCR system reduces NOx. These codes are set when dosing is too low or interrupted.

FaultStopMID 128PSID 90FMI 1Volvo/Mack · DEF dosing too low
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PSID 90 FMI 1 and MID 128 PSID 90 FMI 7 are all about the dEF dosing performance. 1 needs an immediate stop. Start with this check: check the DEF level in the tank and test the fluid for the right concentration before anything else.

How urgent are they?

1 of 2 codes here means stop now; the other 1 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon1

What should I check first?

Check the DEF level in the tank and test the fluid for the right concentration before anything else

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PSID 90 FMI 1DEF dosing too low - NOx limits exceeded, poor DEF quality

    The SCR system sees too little DEF being dosed, or the DEF quality is too poor to reduce NOx.· Real condition
    Stop now

    Causes

    • Poor quality or diluted DEF in the tank
    • DEF line clogged or crystallised
    • DEF doser blocked
    • Aftertreatment control module failure

    Checks

    1. 1Test the DEF with a refractometer; it must read the correct concentration, not water
    2. 2Check the DEF filter and lines for crystals or kinks
    3. 3Run a DEF dosing test with the tool and watch pressure and flow
    4. 4Inspect the doser nozzle for deposits for damage, corrosion or looseness
    5. 5Drain and refill with fresh DEF if the quality is suspect
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PSID 90 FMI 7DEF dosing interrupted - NOx limits exceeded

    NOx limits are exceeded because DEF dosing is interrupted.· Part or controller
    Check soon

    Causes

    • Faulty DEF pump
    • Leak in the DEF hose
    • Low DEF level

    Checks

    1. 1Check the DEF tank level and refill if needed
    2. 2Check the DEF hose and fittings for leaks and crystals
    3. 3Run the DEF pump prime test with the scan tool and watch whether pressure builds and holds
    4. 4Replace the DEF pump if it fails the test and confirm the code does not return
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

Shared checks

Checks, in order

  1. 1Check the DEF level in the tank and test the fluid for the right concentration before anything else
  2. 2Inspect the dosing valve and nozzle for crystals
  3. 3Check the DEF pump pressure with the scan tool and see that it builds and holds during a test
  4. 4Check the NOx sensor readings for a believable difference between the inlet and the outlet values

Causes

  • Poor DEF quality or low DEF
  • Blocked or faulty dosing valve
  • Crystals in the exhaust doser

When to stop

You'll notice: A check lamp comes on and the engine is derated if the problem continues.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.