EF Logo

Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing

Volvo/Mack Fault Code MID 128 SID 22 FMI 2

Crankshaft position sensor intermittent or weak signal

What does Volvo/Mack code MID 128 SID 22 FMI 2 mean?

The crankshaft position sensor signal is intermittent or weak. The ECM relies on this signal for injection timing and engine speed. Urgency: check soon - the machine may derate or limit a function. Check first: check the sensor mounting, torque and air gap against the manual.

FaultCheckMID 128SID 22FMI 2Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing
MID 128
Which control unit reports it
SID 22
Component at fault
FMI 2
Erratic or incorrect data

Can I keep running with it?

Check soon

The machine may derate or limit a function. Find the cause before the next shift.

What should I check first?

Check the sensor mounting, torque and air gap against the manual

Then 3 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

Checks

0 of 4 done

Causes

  • Faulty crankshaft sensor or damaged harness
  • Sensor air gap wrong or tip dirty
  • Damaged flywheel teeth or tone wheel

How it failed

You'll notice: MIL and yellow lamp lit; fuel consumption rises and cylinders can be unbalanced, with power loss and smoke.

Erratic or implausibleRead from FMI 2: erratic or incorrect data

The reading jumps, drifts or disagrees with the sensors around it.

allowed rangetime
The reading against the band the controller allows.
Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good result
A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

When to stop

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Same part, other failures: Camshaft and crankshaft position sensors

3 other codes on this part are also erratic or implausible (MID 128 SID 21 FMI 2, MID 128 SID 21 FMI 8, MID 128 SID 22 FMI 8). When they show together, start at the wiring and connector they share.

All 6 Camshaft and crankshaft position sensors codes on one page

Source

Mack Group 28 Engine Control Module (ECM) Diagnostic Trouble Code Guide, 2010 Emissions CHU/CXU/GU/TD, PV776-89047073 (MID 128 PID/SID tables)

This source lists MID 128 SID 22 FMI 2 and its meaning. The guidance on this page is general, not taken from it.

The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.