Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing
Volvo/Mack Camshaft and crankshaft position sensors fault codes
The engine ECU on MID 128 times injection from two position signals. The camshaft position sensor (SID 21) tells it where the engine is in the four-stroke cycle, and the crankshaft position sensor (SID 22) at the flywheel measures engine speed and position.
More about these partsLess
The ECU also compares the two, so a phase error can come from either sensor or from a trigger wheel.
Where to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
What do these codes mean?
Volvo/Mack codes MID 128 SID 21 FMI 2 to MID 128 SID 22 FMI 8 are all about the camshaft and crankshaft position sensors. Most are erratic or implausible faults; 1 needs an immediate stop. Start with this check: inspect each sensor and its mounting for damage, oil and metal debris.
How urgent are they?
1 of 6 codes here means stop now; the other 5 can wait until the shift ends, but find the cause before the next one.
- Stop now1
- Check soon5
What should I check first?
Inspect each sensor and its mounting for damage, oil and metal debris
Shared checksStop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Volvo/Mack MID 128 SID 21 FMI 2Camshaft position sensor phase error
The ECM sees the camshaft and crankshaft position signals out of step with each other, which it reports as a phase error. Engine timing cannot be confirmed.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Camshaft position sensor misreading or loose
- Timing gear or tone wheel damage causing the camshaft signal to lag
- Wiring or connector fault on the cam sensor circuit
Checks
- 1Read engine speed and cam signal status in the scan tool while cranking
- 2Check the cam sensor mounting and air gap for looseness
- 3Inspect the tone wheel and sensor tip for metal debris or damage
- 4Check the connector and harness for chafing and corrosion
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Volvo/Mack MID 128 SID 21 FMI 3Camshaft position sensor signal missing
The camshaft position signal is missing. Mack lists an open, a short to battery or a short to ground in the CMP sensor circuit.· Shorted highShorted highCheck soonCauses
- Open circuit in the CMP sensor wiring at the valve cover side
- Short to battery or ground in the cam sensor circuit
- Failed camshaft position sensor
- Damaged connector pins
Checks
- 1Check the cam sensor connector and harness for damage and chafing
- 2Measure the sensor supply and signal at the harness plug with the key on
- 3Test each wire for shorts to ground and to battery with the key off
- 4Replace the sensor if the wiring tests good and confirm the code does not return
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Volvo/Mack MID 128 SID 21 FMI 8Camshaft position sensor signal noisy
The camshaft sensor is giving a noisy or erratic signal. Mack ties it to an open in the sensor circuit or a faulty sensor.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Open in the cam sensor circuit
- Faulty cam position sensor
- Loose connector
Checks
- 1Wiggle the harness while watching the engine speed and cam signals in the scan tool
- 2Check the connector pins and seals for corrosion
- 3Inspect the sensor tip for metal debris for damage, corrosion or looseness
- 4Replace the cam sensor if the noise persists and confirm the code does not return
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Volvo/Mack MID 128 SID 22 FMI 2Crankshaft position sensor intermittent or weak signal
The crankshaft position sensor signal is intermittent or weak. The ECM relies on this signal for injection timing and engine speed.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Faulty crankshaft sensor or damaged harness
- Sensor air gap wrong or tip dirty
- Damaged flywheel teeth or tone wheel
Checks
- 1Check the sensor mounting, torque and air gap against the manual
- 2Inspect the flywheel teeth through the inspection hole for damage
- 3Look at the connector and harness for chafing and oil soaking
- 4Replace the sensor if the pattern is weak and confirm the code does not return
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Volvo/Mack MID 128 SID 22 FMI 3Crankshaft position sensor signal missing
The crankshaft position signal is missing, from an open, a short to battery or a short to ground in the CKP sensor circuit. The ECM cannot know engine speed or crank angle, which it needs for injection timing.· Shorted highShorted highStop nowCauses
- Open wire or connector fault on the CKP sensor circuit at the flywheel housing
- Short to battery or ground in the sensor wiring
- Failed crankshaft position sensor or a missing tone wheel signal
- Metal debris on the sensor tip
Checks
- 1Look at the crankshaft sensor connector near the flywheel housing for oil, heat and loose pins
- 2With the key on, measure supply and signal at the harness plug of the crank sensor
- 3Test each crank sensor wire for continuity and for a short to ground or battery
- 4Pull the sensor and look for metal debris on the tip and a damaged flywheel tooth
- 5Replace the sensor if the wiring and the tone wheel are good
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Volvo/Mack MID 128 SID 22 FMI 8Crankshaft position sensor erratic signal
The crankshaft sensor signal is erratic or intermittent, from an open in the sensor circuit or a failing sensor.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Open in the CKP sensor circuit
- Failing crankshaft sensor
- Loose connector or damaged flywheel teeth
Checks
- 1Wiggle the harness while watching engine speed in the scan tool
- 2Check the connector pins and seals for corrosion
- 3Inspect the sensor tip and flywheel teeth for debris or damage
- 4Replace the sensor if the signal stays erratic
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Shared checks
Checks, in order
- 1Inspect each sensor and its mounting for damage, oil and metal debris
- 2Check the connector and harness for damage, chafing and corrosion along the full run to the ECU
- 3Check the camshaft trigger wheel and the flywheel teeth through the housing for damaged or missing teeth
- 4Measure the sensor resistance against the service data
- 5Compare the camshaft and crankshaft signals on a scope if available to see which one drops out
Causes
- Sensor failed or its air gap wrong
- Damaged wiring or connector
- Damaged camshaft trigger wheel or flywheel teeth
- Metal debris on the sensor tip
Most codes here: erratic or implausible (4 of 6)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: The engine cranks long, runs rough or stalls.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
