EF Logo

Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing

Volvo/Mack Fuel actuator or valve control fault codes

The engine ECU drives a fuel actuator or valve with an output. These codes cover shorts and open circuits in that output.

FaultCheckMID 128SID 18FMI 3Volvo/Mack · Fuel actuator or valve control
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 SID 18 FMI 3, MID 128 SID 18 FMI 4 and MID 128 SID 18 FMI 5 are all about the fuel actuator or valve control. None needs an immediate stop. Start with this check: inspect the fuel valve connector and harness for fuel, heat damage and loose pins.

How urgent are they?

None of the 3 codes here means stop now; all 3 can wait until the shift ends, but find the cause before the next one.

  • Check soon3

What should I check first?

Inspect the fuel valve connector and harness for fuel, heat damage and loose pins

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 SID 18 FMI 3Fuel actuator or valve control shorted high

    The engine fuel actuator control circuit is shorted to positive.· Shorted high
    Check soon

    Causes

    • Fuel solenoid control wire shorted to a supply wire
    • Solenoid coil failed shorted
    • ECM output driver fault

    Checks

    1. 1Unplug the solenoid and check the control wire for voltage
    2. 2Measure the solenoid coil resistance at its connector
    3. 3Inspect the harness for chafing against the engine
    4. 4Replace the solenoid after the harness checks good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 SID 18 FMI 4Fuel actuator or valve control shorted low

    The engine fuel actuator control circuit is shorted to ground.· Shorted low
    Check soon

    Causes

    • Fuel solenoid control wire shorted to ground
    • Solenoid coil failed with an internal short to ground
    • ECM output driver fault holding the valve open

    Checks

    1. 1Unplug the solenoid and check the control wire for a short to ground
    2. 2Measure the solenoid coil resistance at its connector
    3. 3Inspect the harness for chafed insulation for damage, corrosion or looseness
    4. 4Replace the solenoid if the harness is good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Volvo/Mack MID 128 SID 18 FMI 5Fuel actuator or valve control circuit open

    The fuel actuator control circuit is open, so the ECM cannot drive the valve and it stays shut, as the Mack table describes.· Open circuit
    Check soon

    Causes

    • Broken wire to the solenoid
    • Solenoid coil open
    • Connector fault

    Checks

    1. 1Measure the coil resistance at the solenoid with the connector unplugged
    2. 2Check continuity of the control wire to the ECM
    3. 3Inspect the connector for pushed-back pins for damage, corrosion or looseness
    4. 4Replace the solenoid if the wiring is good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Inspect the fuel valve connector and harness for fuel, heat damage and loose pins
  2. 2Measure the actuator coil resistance at the connector and compare it with the service data value
  3. 3Check the wire between the ECU and the actuator for a short to ground or to battery voltage
  4. 4Command the actuator with the scan tool and watch the fuel pressure or flow respond

Causes

  • Actuator or valve failed
  • Wire shorted or open
  • Connector corroded

When to stop

You'll notice: The engine loses power or runs poorly, and a check lamp comes on.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.